Smart Structures and Systems

  • 제15권3호
  • /
  • Pages.627-643
  • /
  • 2015
  • /
  • 1738-1584(pISSN)
  • /
  • 1738-1991(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Cable with discrete negative stiffness device and viscous damper: passive realization and general characteristics

  • Chen, Lin (State Key Laboratory for Disaster Reduction of Civil Engineering, Tongji University) ;
  • Sun, Limin (State Key Laboratory for Disaster Reduction of Civil Engineering, Tongji University) ;
  • Nagarajaiah, Satish (Department of Civil and Environmental Engineering, and Dept. of Mechanical Engineering, Rice University)
  • 투고 : 2014.11.27
  • 심사 : 2015.02.15
  • 발행 : 2015.03.25
⟨ 이전 논문 다음 논문 ⟩

초록

Negative stiffness, previously emulated by active or semi-active control for cable vibration mitigation, is realized passively using a self-contained highly compressed spring, the negative stiffness device (NSD).The NSD installed in parallel with a viscous damper (VD) in the vicinity of cable anchorage, enables increment of damper deformation during cable vibrations and hence increases the attainable cable damping. Considering the small cable displacement at the damper location, even with the weakening device, the force provided by the NSD-VD assembly is approximately linear. Complex frequency analysis has thus been conducted to evaluate the damping effect of the assembly on the cable; the displacement-dependent negative stiffness is further accounted by numerical analysis, validating the accuracy of the linear approximation for practical ranges of cable and NSD configurations. The NSD is confirmed to be a practical and cost-effective solution to improve the modal damping of a cable provided by an external damper, especially for super-long cables where the damper location is particularly limited. Moreover, mathematically, a linear negative stiffness and viscous damping assembly has proven capability to represent active or semi-active control for simplified cable vibration analysis as reported in the literature, while in these studies only the assembly located near cable anchorage has been addressed. It is of considerable interest to understand the general characteristics of a cable with the assembly relieving the location restriction, since it is quite practical to have an active controller installed at arbitrary location along the cable span such as by hanging an active tuned mass damper. In this paper the cable frequency variations and damping evolutions with respect to the arbitrary assembly location are then evaluated and compared to those of a taut cable with a viscous damper at arbitrary location, and novel frequency shifts are observed. The characterized complex frequencies presented in this paper can be used for preliminary damping effect evaluation of an adaptive passive or semi-active or active device for cable vibration control.

키워드

참고문헌

  1. Caracoglia, L. and Jones, N.P. (2007a), "Damping of taut-cable systems: Two dampers on a single stay", J. Eng. Mech. - ASCE, 133(10), 1050-1060. https://doi.org/10.1061/(ASCE)0733-9399(2007)133:10(1050)
  2. Caracoglia, L. and Jones, N.P. (2007b), "Passive hybrid technique for the vibration mitigation of systems of interconnected stays", J. Sound Vib., 307(3-5), 849-864. https://doi.org/10.1016/j.jsv.2007.07.022
  3. Chen, L. and Sun, L. (2014), "Laboratory-scale experimental setup for studying cable dampers", J. Eng. Mech. - ASCE, 10.1061/(ASCE)EM.1943-7889.0000878, 04014159.
  4. Chen, Z.Q., Wang, X.Y., Ko, J.M., Ni, Y.Q., Spencer Jr., B.F. and Yang, G. (2003), "MR damping system on Dongting Lake cable-stayed bridge", Proceedings of the SPIE - The Int. Society for Optical Engineering, 229-235.
  5. Fujino, Y. and Hoang, N. (2008), "Design formulas for damping of a stay cable with a damper", J. Struct. Eng. - ASCE, 134(2), 269-278. https://doi.org/10.1061/(ASCE)0733-9445(2008)134:2(269)
  6. Fujino, Y., Kimura, K. and Tanaka, H., (2012), Wind Resistant Design of Bridges in Japan, Springer, Japan.
  7. Hikami, Y. and Shiraishi, N. (1988), "Rain-wind induced vibrations of cables stayed bridges", J. Wind Eng. Ind. Aerod., 29(13), 409-418. https://doi.org/10.1016/0167-6105(88)90179-1
  8. Hoang, N. and Fujino, Y. (2007), "Analytical study on bending effects in a stay cable with a damper", J. Eng. Mech. - ASCE, 133(11), 1241-1246. https://doi.org/10.1061/(ASCE)0733-9399(2007)133:11(1241)
  9. Hoang, N. and Fujino, Y. (2008), "Combined damping effect of two dampers on a stay cable", J. Bridge Eng., 13(3), 299-303. https://doi.org/10.1061/(ASCE)1084-0702(2008)13:3(299)
  10. Hoang, N. and Fujino, Y. (2009), "Multi-mode control performance of nonlinear dampers in stay cable vibrations", Struct. Control Health Monit., 16(7-8), 860-868. https://doi.org/10.1002/stc.364
  11. Hogsberg, J.R. and Krenk, S. (2006), "Linear control strategies for damping of flexible structures", J. Sound Vib., 293(1-2), 59-77. https://doi.org/10.1016/j.jsv.2005.09.014
  12. Hogsberg, J. (2011), "The role of negative stiffness in semi-active control of magneto-rheological dampers", Struct. Control Health Monit., 18(3), 289-304. https://doi.org/10.1002/stc.371
  13. Huang, H., Sun, L. and Jiang, X. (2012), "Vibration mitigation of stay cable using optimally tuned MR damper", Smart Struct. Syst., 9(1), 35-53. https://doi.org/10.12989/sss.2012.9.1.035
  14. Huang, Z. and Jones, N.P. (2011), "Damping of taut-cable systems: Effects of linear elastic spring support", J. Eng. Mech. - ASCE, 137(7), 512-518. https://doi.org/10.1061/(ASCE)EM.1943-7889.0000252
  15. Iemura, H. and Pradono, M.H. (2003), "Application of pseudo-negative stiffness control to the benchmark cable-stayed bridge", J. Struct. Control, 10(3-4), 187-203. https://doi.org/10.1002/stc.25
  16. Iemura, H., Igarashi, A., Pradono, M.H. and Kalantari A. (2006), "Negative stiffness friction damping for seismically isolated structures", Struct. Control Health Monit., 13(2-3), 775-791. https://doi.org/10.1002/stc.111
  17. Iemura, H. and Pradono, M.H. (2009), "Advances in the development of pseudo-negative-stiffness dampers for seismic response control", Struct. Control Health Monit., 16(7-8), 784-799. https://doi.org/10.1002/stc.345
  18. Irvine, H.M. (1981), Cable Structures, Cambridge, MA, U.S.A., MIT Press.
  19. Johnson, E., Baker, G., Spencer, B. and Fujino, Y. (2007), "Semiactive damping of stay cables", J. Eng. Mech. - ASCE, 133(1), 1-11. https://doi.org/10.1061/(ASCE)0733-9399(2007)133:1(1)
  20. Johnson, E.A., Christenson, R.E. and Spencer Jr., B.F. (2003), "Semiactive damping of cables with sag", Comput. - Aided Civil Infrastruct. E., 18(2), 132-146. https://doi.org/10.1111/1467-8667.00305
  21. Kovacs, I. (1982), "Zurfrage der seilschwingungen und der seildampfung", Bautechnik, 59(10), 325-332.
  22. Krenk, S. (2000), "Vibrations of a taut cable with an external damper", J. Appl. Mech. - T. ASME, 67(4), 772-776. https://doi.org/10.1115/1.1322037
  23. Krenk, S. and Hogsberg, J. (2014), "Tuned mass absorber on a flexible structure", J. Sound Vib., 333(6), 1577-1595. https://doi.org/10.1016/j.jsv.2013.11.029
  24. Krenk, S. and Hogsberg, J.R. (2005), "Damping of cables by a transverse force", J. Eng. Mech. - ASCE, 131 (4), 340-348. https://doi.org/10.1061/(ASCE)0733-9399(2005)131:4(340)
  25. Krenk, S. and Nielsen, S.R.K. (2002), "Vibrations of a shallow cable with a viscous damper", P. Roy. Soc. Lond., Series A, 458(2018), 339-357. https://doi.org/10.1098/rspa.2001.0879
  26. Kumarasena, S., Jones, N.P., Irwin, P. and Taylor P. (2007), Wind-Induced Vibration of Stay Cables, Report.
  27. Li, H., Liu, M. and Ou, J. (2008), "Negative stiffness characteristics of active and semi-active control systems for stay cables", Struct. Control Health Monit., 15(2), 120-142. https://doi.org/10.1002/stc.200
  28. Main, J.A. (2002), Modeling the vibrations of a stay cable with attached damper, Ph.D. Dissertation, Johns hopkins University, Baltimore, Maryland.
  29. Main, J.A. and Jones, N.P. (2002a), "Free vibrations of taut cable with attached damper. I: Linear viscous damper", J. Eng. Mech. - ASCE, 128(10), 1062-1071. https://doi.org/10.1061/(ASCE)0733-9399(2002)128:10(1062)
  30. Main, J.A. and Jones, N.P. (2002b), "Free vibrations of taut cable with attached damper. II: Nonlinear damper", J. Eng. Mech. - ASCE, 128(10), 1072-1081. https://doi.org/10.1061/(ASCE)0733-9399(2002)128:10(1072)
  31. Main, J.A. and Jones, N.P. (2007a), "Vibration of tensioned beams with intermediate damper. I: Formulation, influence of damper location", J. Eng. Mech. - ASCE, 133(4), 369-378. https://doi.org/10.1061/(ASCE)0733-9399(2007)133:4(369)
  32. Main, J.A. and Jones, N.P. (2007b), "Vibration of tensioned beams with intermediate damper. II: Damper near a support", J. Eng. Mech. - ASCE, 133(4), 379-388. https://doi.org/10.1061/(ASCE)0733-9399(2007)133:4(379)
  33. Main, J.A. and Krenk, S. (2005), "Efficiency and tuning of viscous dampers on discrete systems", J. Sound Vib., 286(1-2), 97-122. https://doi.org/10.1016/j.jsv.2004.09.022
  34. Nagarajaiah, S. (2009), "Adaptive passive, semiactive, smart tuned mass dampers: identification and control using empirical mode decomposition, Hilbert transform, and short-term fourier transform", Struct. Control Health Monit., 16(7-8), 800-841, DOI: 10.1002/stc.349.
  35. Ou, J. and Li, H. (2010), "Analysis of capability for semi-active or passive damping systems to achieve the performance of active control systems", Struct. Control Health Monit., 17(7), 778-794. https://doi.org/10.1002/stc.408
  36. Pacheco, B.M., Fujino, Y. and Sulekh, A. (1993), "Estimation curve for modal damping in stay cables with viscous damper", J. Struct. Eng. - ASCE, 119(6), 1961-1979. https://doi.org/10.1061/(ASCE)0733-9445(1993)119:6(1961)
  37. Pasala, D., Sarlis, A., Nagarajaiah, S., Reinhorn, A., Constantinou, M. and Taylor, D. (2013), "Adaptive negative stiffness: New structural modification approach for seismic protection", J. Struct. Eng. - ASCE, 139(7), 1112-1123, DOI: 10.1061/(ASCE)ST.1943-541X.0000615.
  38. Pasala, D., Sarlis, A., Reinhorn, A., Nagarajaiah, S., Constantinou, M. and Taylor, D. (2014), "Simulated bilinear-elastic behavior in a SDOF elastic structure using negative stiffness device: Experimental and analytical study", J. Struct. Eng. - ASCE, 140(2), 04013049. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000830
  39. Sarlis, A., Pasala, D., Constantinou, M., Reinhorn, A., Nagarajaiah, S. and Taylor, D. (2013), "Negative stiffness device for seismic protection of structures", J. Struct. Eng. - ASCE, 139(7), 1124-1133. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000616
  40. Spencer, B. and Nagarajaiah, S. (2003), "State of the art of structural control", J. Struct. Eng. - ASCE, 129 (7), 845-856. https://doi.org/10.1061/(ASCE)0733-9445(2003)129:7(845)
  41. Sun, C. and Nagarajaiah, S. (2014), "Study on semi-active tuned mass damper with variable damping and stiffness under seismic excitations", Struct. Control Health Monit., 21(6), 890-906. https://doi.org/10.1002/stc.1620
  42. Sun, C., Nagarajaiah, S. and Dick, A. (2014), "Family of smart tuned mass dampers with variable frequency under harmonic excitations and ground motions: closed-form evaluation", Smart Struct. Syst., 13(2), 319-341. https://doi.org/10.12989/sss.2014.13.2.319
  43. Sun, L. and Huang, H. (2008), Design, implementation and measurement of cable dampers for large cable-stayed bridges, IABSE Congress Report, 17(16), 242-243. https://doi.org/10.2749/222137908796292498
  44. Sun, L. and Chen, L. (2015), "Free vibrations of a taut cable with a general viscoelastic damper modeled by fractional derivatives", J. Sound Vib., 335(2015), 19-33. https://doi.org/10.1016/j.jsv.2014.09.016
  45. Sun, L., Shi, C., Zhou, H. and Cheng, W. (2004), "A full-scale experiment on vibration mitigation of stay cable", Proceedings of the IABSE Symp. Rep., IABSE Symp., Shanghai 2004: Metropolitan Habitats and Infrastructure, IABSE, Zurich, Switzerland.
  46. Tabatabai, H. and Mehrabi, A.B. (2000), "Design of mechanical viscous dampers for stay cables", J. Bridge Eng., 5(2), 114-123. https://doi.org/10.1061/(ASCE)1084-0702(2000)5:2(114)
  47. Weber, F. and Boston, C. (2011), "Clipped viscous damping with negative stiffness for semi-active cable damping", Smart Mater. Struct., 20(4), 045007. https://doi.org/10.1088/0964-1726/20/4/045007
  48. Weber, F., Boston, C. and Maslanka, M. (2011), "An adaptive tuned mass damper based on the emulation of positive and negative stiffness with an MR damper", Smart Mater. Struct., 20(1), 015012. https://doi.org/10.1088/0964-1726/20/1/015012
  49. Xu, Y.L. and Yu, Z. (1998), "Vibration of inclined sag cables with oil dampers in cable-stayed bridges", J. Bridge Eng., 3(4), 194-203. https://doi.org/10.1061/(ASCE)1084-0702(1998)3:4(194)
  50. Xu, Y.L., Yu, Z. and Ko, J.M. (1998), "Forced vibration studies of sagged cables with oil damper using a hybrid method", Eng. Struct., 20(8), 692-705. https://doi.org/10.1016/S0141-0296(97)00100-4
  51. Zhou, H., Sun, L. and Xing, F. (2014a), "Damping of full-scale stay cable with viscous damper: Experiment and analysis", Adv. Struct. Eng., 17(2), 265-274. https://doi.org/10.1260/1369-4332.17.2.265
  52. Zhou, H., Sun, L. and Xing, F. (2014b), "Free vibration of taut cable with a damper and a spring", Struct. Control Health Monit., 21(6), 996-1014. https://doi.org/10.1002/stc.1628

피인용 문헌

  1. Experimental investigation on a passive auto-tuning mass damper for vibration control 2017, https://doi.org/10.1007/s40435-017-0381-z
  2. Inertial mass damper for mitigating cable vibration vol.24, pp.10, 2017, https://doi.org/10.1002/stc.1986
  3. Free vibration and damping of a taut cable with an attached viscous mass damper 2018, https://doi.org/10.1007/s12205-017-1167-8
  4. Performance Comparison between Passive Negative-Stiffness Dampers and Active Control in Cable Vibration Mitigation vol.22, pp.9, 2017, https://doi.org/10.1061/(ASCE)BE.1943-5592.0001088
  5. Semi-active damping with negative stiffness for multi-mode cable vibration mitigation: approximate collocated control solution vol.24, pp.11, 2015, https://doi.org/10.1088/0964-1726/24/11/115015
  6. Soil-Structure Interaction for Integrated Design of Weakened and Damped Structures vol.11, pp.04, 2017, https://doi.org/10.1142/S1793431117500130
  7. Development of a Self-Powered Magnetorheological Damper System for Cable Vibration Control vol.8, pp.1, 2018, https://doi.org/10.3390/app8010118
  8. Steady-State Analysis of Cable with Nonlinear Damper via Harmonic Balance Method for Maximizing Damping vol.143, pp.2, 2017, https://doi.org/10.1061/(ASCE)ST.1943-541X.0001645
  9. Cable vibration control with both lateral and rotational dampers attached at an intermediate location vol.377, 2016, https://doi.org/10.1016/j.jsv.2016.04.028
  10. Residual mode correction in calibrating nonlinear damper for vibration control of flexible structures vol.406, 2017, https://doi.org/10.1016/j.jsv.2017.06.015
  11. Cables interconnected with tuned inerter damper for vibration mitigation vol.151, 2017, https://doi.org/10.1016/j.engstruct.2017.08.009
  12. Modeling and control performance of a negative stiffness damper for suppressing stay cable vibrations vol.23, pp.4, 2016, https://doi.org/10.1002/stc.1809
  13. Free vibration of a taut cable with a damper and a concentrated mass vol.25, pp.11, 2018, https://doi.org/10.1002/stc.2251
  14. Refined damper design formula for a cable equipped with a positive or negative stiffness damper vol.25, pp.10, 2018, https://doi.org/10.1002/stc.2236
  15. Nonlinear impact of negative stiffness dampers on stay cables vol.5, pp.1, 2015, https://doi.org/10.12989/smm.2018.5.1.015
  16. Match of Negative Stiffness and Viscous Damping in a Passive Damper for Cable Vibration Control vol.2019, pp.None, 2019, https://doi.org/10.1155/2019/3208321
  17. Refined Study on Free Vibration of a Cable with an Inertial Mass Damper vol.9, pp.11, 2019, https://doi.org/10.3390/app9112271
  18. Experimental evaluation of an inertial mass damper and its analytical model for cable vibration mitigation vol.23, pp.6, 2015, https://doi.org/10.12989/sss.2019.23.6.589
  19. Performance evaluation of inerter-based damping devices for structural vibration control of stay cables vol.23, pp.6, 2015, https://doi.org/10.12989/sss.2019.23.6.615
  20. Vibration control of a stay cable with a rotary electromagnetic inertial mass damper vol.23, pp.6, 2015, https://doi.org/10.12989/sss.2019.23.6.627
  21. Feasibility of Using a Negative Stiffness Damper to Two Interconnected Stay Cables for Damping Enhancement vol.19, pp.6, 2015, https://doi.org/10.1142/s0219455419500585
  22. Free Vibration of a Taut Cable with Two Discrete Inertial Mass Dampers vol.9, pp.18, 2015, https://doi.org/10.3390/app9183919
  23. Modelling and passive control of flexible guiding hoisting system with time-varying length vol.26, pp.1, 2015, https://doi.org/10.1080/13873954.2019.1699121
  24. Investigations on a vertical isolation system with quasi-zero stiffness property vol.25, pp.5, 2015, https://doi.org/10.12989/sss.2020.25.5.543
  25. Negative stiffness devices for vibration isolation applications: A review vol.23, pp.8, 2015, https://doi.org/10.1177/1369433219900311
  26. Full-Scale Experimental Study on Vibration Control of Bridge Suspenders Using the Stockbridge Damper vol.25, pp.8, 2015, https://doi.org/10.1061/(asce)be.1943-5592.0001591
  27. Inertial mass damper for vibration control of cable with sag vol.39, pp.3, 2015, https://doi.org/10.1177/1461348418814967
  28. Modeling, Characterizing, and Testing a Simple, Smooth Negative-Stiffness Device to Achieve Apparent Weakening vol.146, pp.10, 2015, https://doi.org/10.1061/(asce)em.1943-7889.0001823
  29. Apparent-weakening by adaptive passive stiffness shaping along the height of multistory building using negative stiffness devices and dampers for seismic protection vol.220, pp.None, 2015, https://doi.org/10.1016/j.engstruct.2020.110754
  30. A comparative study of multi-mode cable vibration control using viscous and viscoelastic dampers through field tests on the Sutong Bridge vol.224, pp.None, 2015, https://doi.org/10.1016/j.engstruct.2020.111226
  31. Dynamic Characteristics and Responses of Damped Outrigger Tall Buildings Using Negative Stiffness vol.146, pp.12, 2015, https://doi.org/10.1061/(asce)st.1943-541x.0002846
  32. Impact of Damper Stiffness and Damper Support Stiffness on the Performance of a Negative Stiffness Damper in Mitigating Cable Vibrations vol.26, pp.3, 2015, https://doi.org/10.1061/(asce)be.1943-5592.0001683
  33. A unified analysis of negative stiffness dampers and inerter-based absorbers for multimode cable vibration control vol.494, pp.None, 2015, https://doi.org/10.1016/j.jsv.2020.115814
  34. Optimal Design of Dampers for Multi-Mode Cable Vibration Control Based on Genetic Algorithm vol.21, pp.4, 2015, https://doi.org/10.1142/s0219455421500589
  35. Viscous inertial mass damper (VIMD) for seismic responses control of the coupled adjacent buildings vol.233, pp.None, 2015, https://doi.org/10.1016/j.engstruct.2021.111876
  36. Free vibrations of hybrid cable networks with external dampers and pretensioned cross-ties vol.156, pp.None, 2015, https://doi.org/10.1016/j.ymssp.2021.107627
  37. Damping enhancement of the inerter on the viscous damper in mitigating cable vibrations vol.28, pp.1, 2015, https://doi.org/10.12989/sss.2021.28.1.089
  38. Resetting passive stiffness damper with passive negative stiffness device for seismic protection of structures vol.28, pp.8, 2015, https://doi.org/10.1002/stc.2774
  39. Suppression of vortex-induced high-mode vibrations of a cable-damper system by an additional damper vol.242, pp.None, 2021, https://doi.org/10.1016/j.engstruct.2021.112495
  40. Dynamic Characteristics and Responses of Tall Building Structures with Double Negative Stiffness Damped Outriggers vol.10, pp.3, 2015, https://doi.org/10.21022/ijhrb.2021.10.3.229
  41. Non-stationary oscillation of a string on the Winkler foundation subjected to a discrete mass-spring system non-uniformly moving at a sub-critical speed vol.522, pp.None, 2015, https://doi.org/10.1016/j.jsv.2021.116673