DOI QR코드

DOI QR Code

A Study on the Improvement of Efficiency of Heat Transfer of Double Pipe Heat Exchanger with Helical Insert Device on Cooling of a Fuel Cell

연료전지 냉각용 헬리컬 인서트디바이스 이중관열교환기의 열전달 성능 향상에 관한 연구

  • Received : 2015.11.27
  • Accepted : 2015.12.07
  • Published : 2015.12.31

Abstract

The present study was conducted on the improvement of the heat transfer performance of double pipe heat exchangers with helical insert device. Double pipe heat exchangers with helical insert device were studied for improvement of the heat transfer performance of double pipe heat exchangers with helical insert device and plain double pipe heat exchangers were also studied to comparatively analyze heat transfer performance. Experimental results were derived on changes in the Reynold's numbers of the cooling water flowing in helical and plain double pipe heat exchangers and changes in the heat flux of the air. Thereafter, to verify the reliability of the experimental results, the theoretical total energy and the experimental total energy were comparatively analyzed and the following results were derived. The thermal energy of the calorie lost by the hot air and that of the calorie obtained by the cooling water were well balanced. The experiments of plain double pipe heat exchangers and double pipe heat exchangers with helical insert device were conducted under normal conditions and the theoretical overall heat transfer coefficient value and the experimental overall heat transfer coefficient value coincided well with each other. In both plain double pipe heat exchangers and double pipe heat exchangers with helical insert device, heat transfer rates increased as the cooling water flow velocity increased. Under the same experimental conditions, the heat transfer performance of double pipe heat exchangers with helical insert device was shown to be higher by approximately 1.5 times than that of plain double pipe heat exchangers.

Keywords

References

  1. Bergles, A. E. and Lopina, R. F.(1969). Heat Transfer and Pressure Drop in Tape Generated Swirl Flow of Single-Phase Water." J. Heat Transfer, Trans. ASME. Vol. 9, 434-442.
  2. Cho, D. H.(2015). A Study on the Improvement of Efficiency of Heat Transfer of Double Pipe Heat Exchanger with Helical Insert Device on Cooling of a Fuel Cell, Jour. Fish. Mar. Sci. Edu., 27(6).
  3. Chyu, M. K..Yu, Y..Ding, H..Downs, J. P.. Soechting, F. O.(1997). "Concavity enhanced heat transfer in an internal cooling passage," IGTI, 97-DT-437, Oriando, Florida, USA.
  4. Fan, L. T..Lin L. S. and Azer, N. Z.(1978). "Surface Renewal Model of Condensation Heat Transfer in Tubes with in-line static Mixers." Int. J. Heat mass Transfer vol.21, 849-854. https://doi.org/10.1016/0017-9310(78)90176-X
  5. Garimella, S. and Christensen, R. N.(1995). Heat Transfer and Pressure Drop Characteristics of Spirally Fluted Annuli: Part I- Hydropdynamics, Journal of Heat Transfer, Vol. 117, 54-60. https://doi.org/10.1115/1.2822323
  6. Incropera, F. P..Dewitt, D. P..Bergman, T. L. and Lavine, A. S.(2014). Fundamental of Heat Transfer, Incropera, 420-450.
  7. Lim, T. W..You, S. S.(2008). A Study on the microcooling Fin Fabrication Process for Enhancing Boiling Heat Transfer, Jour. Fish. Mar. Sci. Edu., 19(3), 366-372.
  8. Lim, T. W..Park, J. U. & Kim. J. H.(2002). A Study on Heat Transfer and Pressure Drop in Flow Boiling of Binary Mixtures in a Uniformly Heated Horizontal Tube, Jour. Fish. Mar. Sci. Edu., 14(2), 177-190.
  9. MIFFAF(2012). Annual Statistics of Agriculture, Forestry, Fishery and Food.
  10. Park, J. U..Cho, D. H.(2004). A Study on Heat Transfer Characteristics of Helical Coiled Tube, Jour. Fish. Mar. Sci. Edu., 16(2), 257-270.
  11. Smithberg, E. and Landis, F.(1964). "Friction and Forced Convection Heat-Transfer Characteristics in Tubes With Twisted Tape Swirl Generators." J. Heat Transfer.Trans. ASME, vol.86, 39-49. https://doi.org/10.1115/1.3687060
  12. Thorsen, R. and Landis, F.(1968). "Friction and Heat Transfer Characteristics in Turbulent Swirl Flow Subjected to Large Transverse Temperature Gradients." J. Heat Transfer Trans. ASME, vol.90, 87-97. https://doi.org/10.1115/1.3597466