DOI QR코드

DOI QR Code

Plastic mechanism analysis of vehicle roof frames consisting of spot-welded steel hat sections

  • Bambach, M.R. (Transport and Road Safety (TARS), Faculty of Science, Old Main Building, University of New South Wales)
  • 투고 : 2013.09.25
  • 심사 : 2014.05.27
  • 발행 : 2014.12.25

초록

Plastic mechanism analysis of structures subjected to large deformation has long been used in order to determine collapse mechanisms of steel structures, and the energy absorbed in plastic deformation during such collapses. In this paper the technique is applied to vehicle roof structures that undergo large plastic deformation as a result of rollover crashes. The components of such roof structures are typically steel spot-welded hat-type sections. Ten different deformation mechanisms are defined from investigations of real-world rollover crashes, and an analytical technique to determine the plastic collapse load and energy absorption of such mechanisms is determined. The procedure is presented in a generic manner, such that it may be applied to any vehicle structure undergoing a rollover induced collapse. The procedure is applied to an exemplar vehicle, in order to demonstrate its application in determining the energy absorbed in the deformation of the identified collapse mechanisms. The procedure will be useful to forensic crash reconstructionists, in order to accurately determine the initial travel velocity of a vehicle that has undergone a rollover and for which the post-crash vehicle deformation is known. It may also be used to perform analytical studies of the collapse resistance of vehicle roof structures for optimisation purposes, which is also demonstrated with an analysis of the effect of varying the geometric and material properties of the roof structure components of the exemplar vehicle.

키워드

참고문헌

  1. AS 4100 (1998), Australian Standard, Steel Structures, Standards Australia, Sydney.
  2. Bambach, M.R., Jama, H.H., Zhao, X.L. and Grzebieta, R.H. (2008), "Hollow and concrete filled steel hollow sections under transverse impact loads", Eng. Struct., 30(10), 2859-2870. https://doi.org/10.1016/j.engstruct.2008.04.003
  3. Bambach, M.R., Tan, G. and Grzebieta, R.H. (2009), "Steel spot-welded hat sections with perforations subjected to large deformation pure bending", Thin Wall. Struct., 47(11), 1305-1315. https://doi.org/10.1016/j.tws.2009.03.010
  4. Bambach, M.R. (2011), "Design of hollow and concrete filled steel and stainless steel tubular columns for transverse impact loads", Thin Wall. Struct., 49(10), 1251-1260. https://doi.org/10.1016/j.tws.2011.05.009
  5. Bambach, M.R., Grzebieta, R., McIntosh, A.S. and Mattos, G. (2013), "Cervical and thoracic spine injury from interactions with vehicle roofs in pure rollover crashes", Accid. Anal. Prevent., 50, 34-43. https://doi.org/10.1016/j.aap.2012.10.006
  6. Elchalakani, M. and Fernando, D. (2012), "Plastic mechanism analysis of unstiffened steel I-section beams strengthened with CFRP under 3-point bending", Thin Wall. Struct., 53, 58-71. https://doi.org/10.1016/j.tws.2012.01.005
  7. Elchalakani, M. (2007), "Plastic mechanism analyses of circular tubular members under cyclic loading", Thin Wall. Struct., 45(12), 1044-1057. https://doi.org/10.1016/j.tws.2007.07.005
  8. Elchalakani, M., Zhao, X.L. and Grzebieta, R.H. (2002), "Plastic mechanism analysis of circular tubes under pure bending", Int. J. Mech. Sci., 44(6), 1117-1143. https://doi.org/10.1016/S0020-7403(02)00017-6
  9. Kecman, D. (1983), "Bending collapse of rectangular and square section tubes", Int. J. Mech. Sci., 25(9-10), 623-36. https://doi.org/10.1016/0020-7403(83)90072-3
  10. Kotelko, M. (2008), "Alternative solutions of the problem of load-capacity of thin-walled plated structures", Mech. Mech. Eng., 12(4), 323-336.
  11. Maduliat, S., Bambach, M.R. and Zhao, X.L. (2012), "Yield line mechanism analysis of cold-formed channel sections with edge stiffeners under bending", Struct. Eng. Mech., 42(6), 883-897. https://doi.org/10.12989/sem.2012.42.6.883
  12. NHTSA (2013), Traffic Safety Facts: Passenger Vehicles: 2011 Data, DOT HS 811 827.
  13. NHTSA (2012), National Automotive Sampling System (NASS), Crashworthiness Data System (CDS), Accessible at: http://www.nhtsa.gov/NASS.
  14. Papangelis, J.P. and Hancock, G.J. (1995), "Computer analysis of Thin-Walled Structural Members", Comput. Struct., 56(1), 157-176. https://doi.org/10.1016/0045-7949(94)00545-E
  15. Setiyono, H. (2007), "Plastic mechanism and elastic-analytical approaches applied to estimate the strength of an axially compressed-thin-walled channel steel section beam", Int. J. Mech. Sci., 49(3), 257-266. https://doi.org/10.1016/j.ijmecsci.2006.09.009
  16. Sharma, D., Stern, S., Brophy, J. and Choi, E. (2007), "An overview of NHTSA's crash reconstruction software", 20th Enhanced Safety of Vehicles Conference Proceedings, Paper 07-0211, Lyon, France.
  17. Tan, G., Bambach, M.R. and Grzebieta, R.H. (2008), "Database of Australian vehicle pillar profiles - General profiles and profiles from vehicles involved in rollover crashes", Monash University, Research Report No RR8.
  18. Ungureanu, V., Koteko, M., Mania, R.J. and Dubina, D. (2010), "Plastic mechanisms database for thinwalled cold-formed steel members in compression and bending", Thin Wall. Struct., 48(10-11), 818-826 https://doi.org/10.1016/j.tws.2010.01.004
  19. Ye, J.H., Zhao, X.L., Van, B.D. and A-Mahaidi, R. (2007), "Plastic mechanism analysis of fabricated square and triangular sections under axial compression", Thin Wall. Struct., 45(2), 135-148. https://doi.org/10.1016/j.tws.2007.02.006
  20. Young, D., Grzebieta, R.H., Bambach, M.R, McIntosh, A. and Frechede, B. (2007), "Diving vs Roof Intrusion: a review of rollover injury causation", Int. J. Crashworth., 12(6), 609-628. https://doi.org/10.1080/13588260701497946