Smart Structures and Systems

  • 제14권5호
  • /
  • Pages.901-916
  • /
  • 2014
  • /
  • 1738-1584(pISSN)
  • /
  • 1738-1991(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Simulation study of magnetorheological testing cell design by incorporating all basic operating modes

  • Mughni, Mohd J. (Malaysia-Japan International Institute of Technology, Universiti Teknologi Malaysia) ;
  • Mazlan, Saiful A. (Malaysia-Japan International Institute of Technology, Universiti Teknologi Malaysia) ;
  • Zamzuri, Hairi (Vehicle System Engineering Research Laboratory, Universiti Teknologi Malaysia) ;
  • Yazid, Izyan I.M. (Malaysia-Japan International Institute of Technology, Universiti Teknologi Malaysia) ;
  • Rahman, Mohd A.A. (Malaysia-Japan International Institute of Technology, Universiti Teknologi Malaysia)
  • 투고 : 2013.05.28
  • 심사 : 2014.01.12
  • 발행 : 2014.11.25
⟨ 이전 논문 다음 논문 ⟩

초록

Magnetorheological (MR) fluid is one of the field-responsive fluids that is of interest to many researchers due to its high yield stress value, which depends on the magnetic field strength. Similar to electrorheological (ER) fluid, the combination of working modes is one of the techniques to increase the performance of the fluids with limited focus on MR fluids. In this paper, a novel MR testing cell incorporated with valve, shear and squeeze operational modes is designed and constructed in order to investigate the behaviour of MR fluid in combined mode. The magnetic field distribution in the design concept was analyzed using finite element method in order to verify the effective areas of each mode have the acceptable range of flux density. The annular gap of valve and shear were fixed at 1 mm, while the squeeze gap between the parallel circular surfaces was varied up to 20 mm. Three different coil configurations, which were made up from 23 SWG copper wires were set up in the MR cell. The simulation results indicated that the magnetic field distributed in the squeeze gap was the highest among the other gaps with all coils were subjected to a constant applied current of 1 A. Moreover, the magnetic flux densities in all gaps were in a good range of magnitude based on the simulations that validated the proposed design concept. Hence, the 3D model of the MR testing cell was designed using Solidworks for manufacturing processes.

키워드

과제정보

연구 과제 주관 기관 : Fundamental Research Grant Scheme (FRGS)

참고문헌

  1. Bhowmik, S., Weber, F. and Hogsberg, J. (2013), "Experimental calibration of forward and inverse neural networks for rotary type magnetorheological damper", Struct. Eng. Mech., 46(5), 673-693. https://doi.org/10.12989/sem.2013.46.5.673
  2. Bose, H. and Ehrlich, J. (2012), "Magnetorheological dampers with various designs of hybrid magnetic circuits", J. Intel. Mat. Syst. Str., 23(9), 979-987. https://doi.org/10.1177/1045389X11433497
  3. Brigley, M., Choi, Y.T., Wereley, N.M. and Choi, S.B. (2007), "Magnetorheological isolators using multiple fluid modes", J. Intel. Mat. Syst. Str., 18(12), 1143-1148. https://doi.org/10.1177/1045389X07083129
  4. Carletto, P. and Bossis, G. (2003), "Field-induced structures and rheology of a magnetorheological suspension confined between two walls", J. Phys. - Condens. Mat., 15(15), S1437-S1449. https://doi.org/10.1088/0953-8984/15/9/307
  5. El Wahed, A.K. and McEwan, C.A. (2011), "Design and performance evaluation of magnetorheological fluids under single and mixed modes", J. Intel. Mat. Syst. Str., 22(7), 631-643. https://doi.org/10.1177/1045389X11404453
  6. Gavin, H.P. (1998), "Design method for high-force electrorheological dampers", Smart Mater. Struct., 7(5), 664-673. https://doi.org/10.1088/0964-1726/7/5/010
  7. Genc, S. and Phule, P.P. (2002), "Rheological properties of magnetorheological fluids", Smart Mater. Struct., 11(1), 140-146. https://doi.org/10.1088/0964-1726/11/1/316
  8. Goncalves, F.D. and Carlson, J.D. (2009), "An alternate operation mode for MR fluids-magnetic gradient pinch", J. Phys.: Conf. Ser., 149(1), 012050. https://doi.org/10.1088/1742-6596/149/1/012050
  9. Guo, C., Gong, X., Xuan, S., Qin, L. and Yan, Q. (2013), "Compression behaviors of magnetorheological fluids under nonuniform magnetic field", Rheol. Acta, 52(2), 165-176. https://doi.org/10.1007/s00397-013-0678-6
  10. Hagenbuchle, M. and Liu, J. (1997), "Chain formation and chain dynamics in a dilute magnetorheological fluid", Appl. Optics, 36(30), 7664-7671. https://doi.org/10.1364/AO.36.007664
  11. Hong, S.R., Wereley, N.M., Choi, Y.T. and Choi, S.B. (2008), "Analytical and experimental validation of a nondimensional Bingham model for mixed-mode magnetorheological dampers", J. Sound Vib., 312(3), 399-417. https://doi.org/10.1016/j.jsv.2007.07.087
  12. Imaduddin, F., Mazlan, S.A., Zamzuri, H. and Yazid, I.I.M. (2013), "Design and performance analysis of a compact magnetorheological valve with multiple annular and radial gaps", J. Intel. Mat. Syst. Str., DOI: 10.1177/1045389X13508332.
  13. Ismail, I., Mazlan, S.A., Zamzuri, H. and Olabi, A.G. (2012), "Fluid-particle separation of magnetorheological fluid in squeeze mode", Jpn. J. Appl. Phys., 51(6), 067301. https://doi.org/10.7567/JJAP.51.067301
  14. Jolly, M.R., Bender, J.W. and Carlson, J.D. (1999), "Properties and applications of commercial magnetorheological fluids", J. Intel. Mat. Syst. Str., 10(1), 5-13. https://doi.org/10.1177/1045389X9901000102
  15. Mazlan, S.A., Ismail, I., Zamzuri, H. and Abd Fatah, A.Y. (2011), "Compressive and tensile stresses of magnetorheological fluids in squeeze mode", Int. J. Appl. Electrom., 36(4), 327-337.
  16. Mazlan, S.A., Issa, A., Chowdhury, H.A. and Olabi, A.G. (2009), "Magnetic circuit design for the squeeze mode experiments on magnetorheological fluids", Mater. Design, 30(6), 1985-1993. https://doi.org/10.1016/j.matdes.2008.09.009
  17. Nguyen, Q.H., Choi, S.B. and Wereley, N.M. (2008), "Optimal design of magnetorheological valves via a finite element method considering control energy and a time constant", Smart Mater. Struct., 17(2), 025024. https://doi.org/10.1088/0964-1726/17/2/025024
  18. Tang, X., Zhang, X., Tao, R. and Rong, Y.M. (2000), "Structure-enhanced yield stress of magnetorheological fluids", J. Appl. Phys., 87(5), 2634-2638. https://doi.org/10.1063/1.372229
  19. Tian, Y., Meng, Y., Mao, H. and Wen, S. (2002), "Electrorheological fluid under elongation, compression and shearing", Phys. Rev. E., 65(3), 031507. https://doi.org/10.1103/PhysRevE.65.031507
  20. Wang, H., Bi, C., Kan, J., Gao, C. and Xiao, W. (2011), "The mechanical property of magnetorheological fluid under compression, elongation and shearing", J. Intel. Mat. Syst. Str., 22(8), 811-816. https://doi.org/10.1177/1045389X11409605
  21. Wang, J. and Meng, G. (2001), "Magnetorheological fluid devices: principles, characteristics and applications in mechanical engineering", P. I. Mech. Eng. L-J. Mat., 215(3), 165-174.
  22. Wereley, N.M. and Pang, L. (1998), "Nondimensional analysis of semi-active electrorheological and magnetorheological dampers using approximate parallel plate models", Smart Mater. Struct., 7(5), 732-743. https://doi.org/10.1088/0964-1726/7/5/015
  23. Yazid, I.I.M., Mazlan, S.A., Kikuchi, T., Zamzuri, H. and Imaduddin, F. (2014), "Design of magnetorheological damper with a combination of shear and squeeze modes", Mater. Design, 54, 87-95. https://doi.org/10.1016/j.matdes.2013.07.090
  24. Zeinali, M., Mazlan, S.A., Abd Fatah, A.Y. and Zamzuri, H. (2013), "A phenomenological dynamic model of a magnetorheological damper using a neuro-fuzzy system", Smart Mater. Struct., 22(12), 125013. https://doi.org/10.1088/0964-1726/22/12/125013