한국자동차공학회논문집 (Transactions of the Korean Society of Automotive Engineers)

  • 제22권6호
  • /
  • Pages.23-30
  • /
  • 2014
  • /
  • 1225-6382(pISSN)
  • /
  • 2234-0149(eISSN)
한국자동차공학회 (The Korean Society of Automotive Engineers)
권호 표지
DOI QR코드

DOI QR Code

자동차 전동 시스템을 위한 Programmable 저역 통과 필터 기반의 상전류 극성 판단 및 데드타임 보상

Dead Time Compensation and Polarity Check of Phase Currents Based on Programmable Low-pass Filter for Automotive Electric Drive Systems

  • 최진철 (창원대학교 대학원 제어계측공학과) ;
  • 이강석 (창원대학교 대학원 제어계측공학과) ;
  • 이우택 (창원대학교 제어계측공학과2)
  • Choi, Chinchul (Department of Control and Instrumenation Engineering, Graduate School of Changwon National University) ;
  • Lee, Kangseok (Department of Control and Instrumenation Engineering, Graduate School of Changwon National University) ;
  • Lee, Wootaik (Department of Control and Instrumenation Engineering, Changwon National University)
  • 투고 : 2013.12.03
  • 심사 : 2014.04.21
  • 발행 : 2014.09.01
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

This paper proposes a dead time compensation method for an AC motor drive using phase current polarity information which is detected based on a digital programmable low-pass filter (PLPF). The polarity detection using the PLPF is an alternative solution of a conventional method which uses a general low-pass filter (LPF) and hysteresis bands in order to avoid jittering due to noises. The PLPF not only adjusts its cutoff frequency according to the synchronous frequency of AC motors but also eliminates a gain attenuation and phase delay which are main problems of the general LPF. Through the PLPF, a fundamental component signal without gain and phase distortions is extracted from the measured raw current signal with noise. By use of the fundamental component, the polarity of current is effectively detected by reducing the hysteresis band. Finally, the proposed method compensates the dead time effects by adding or subtracting average voltage value to voltage references of the controller according to the detected current polarity information. The proposed compensation method is experimentally verified by compared with the conventional method.

키워드

참고문헌

  1. J. Y. Yoo, J. H. Lee and H. T. Moon, "Current Sensorless Drive Method for Electric Power Steeing," Int. J. Automotive Technology, Vol.13, No.7, pp.1141-1147, 2012. https://doi.org/10.1007/s12239-012-0117-1
  2. M. H. Lee, S. K. Ha, J. I. Bae, J. H. Park, H. G. Park, H. J. Choi and H. H. Chun, " Development of a Hardware in the Loop Simulation System for Electric Power Steering in Vehicles," Int. J. Automotive Technology, Vol.12, No.5, pp.733-744, 2011. https://doi.org/10.1007/s12239-011-0085-x
  3. J. Song, K. Boo and J. Lee, "Evaluation of Performance and Development of Control Method of New Electric Power Steering System (EPS-TT)," Transactions of KSAE, Vol.12, No.5, pp.145-161, 2004.
  4. J. Kim and J. B. Song, "Control Logic Using Torque Map for a Column-type Electric Power Steering System," Transactions of KSAE, Vol.8, No.4, pp.186-193, 2000.
  5. X. Zhao, X. Shi, J. Chen and X. Li, "Dynamic Correction of the Steering-characteristic Curve and Application to an EPS Control System," Int. J. Automotive Technology, Vol.12, No.2, pp.243-249, 2011. https://doi.org/10.1007/s12239-011-0029-5
  6. C. C. Choi, K. T. Bae and W. T. Lee, "Development of Average Inverter Model for Analysis of Automotive Electric Drive System," Transactions of KSAE, Vol.18, No.6, pp.23-30, 2010.
  7. Y. Murai, T. Watanabe and H. Iwasaki, "Waveform Distortion and Correction Circuit for PWM Inverters with Switching Lag-times," Industry Applications, IEEE Transactions on, Vol.IA-23, Issue 5, pp.881-886, 1987. https://doi.org/10.1109/TIA.1987.4504998
  8. J. S. Gi and M. H. Park, "The Analysis and Compensation of Dead-time Effects in PWM Inverters," Industrial Electronics, IEEE Transactions on, Vol.38, No.2, pp.108-114, 1991. https://doi.org/10.1109/41.88903
  9. D. Leggate and R. J. Kerkman, "Pulse-based Dead-time Compensator for PWM Voltage Inverters," Industrial Electronics, IEEE Transactions on, Vol. 44, No.2, pp.191-197, 1997. https://doi.org/10.1109/41.564157
  10. S. Kim, T. Park, J. Yoo, G. Park and N. Kim, "Dead Time Compensation Strategy in a Vector-controlled Induction Machine," KIEE, Vol.47, No.6, pp.788-793, 1998.
  11. S. Hwang and J. Kim, "Dead Time Compensation Method for Voltage-Fed PWM Inverter," Energy Conversion, IEEE Transactions on, Vol.25, No.1, pp.1-10, 2009.
  12. D. Wilson, Making Low-distortion Motor Waveforms with the MC68HC708MP16, Freescale Semiconductor, Inc., 1997.
  13. Freescale, DSP56800 Family Manual, 2005.
  14. M. Brejl, M. Princ and V. Phillipov, Using the Analog Sensing for AC Motors (ASAC) eTPU Function, 2012.