DOI QR코드

DOI QR Code

Hydraulic fracturing experiments of highly deviated well with oriented perforation technique

  • Zhu, Hai Y. (State Key Laboratory of Oil & Gas Reservoir Geology and Exploitation, Southwest Petroleum University) ;
  • Deng, Jin G. (State Key Laboratory of Petroleum Resource and Prospecting (China University of Petroleum, Beijing)) ;
  • Liu, Shu J. (CNOOC Research Institute) ;
  • Wen, Min (CNOOC Research Institute) ;
  • Peng, Cheng Y. (CNOOC Research Institute) ;
  • Li, Ji R. (State Key Laboratory of Petroleum Resource and Prospecting (China University of Petroleum, Beijing)) ;
  • Chen, Zi J. (State Key Laboratory of Petroleum Resource and Prospecting (China University of Petroleum, Beijing)) ;
  • Hu, Lian B. (State Key Laboratory of Petroleum Resource and Prospecting (China University of Petroleum, Beijing)) ;
  • Lin, Hai (State Key Laboratory of Petroleum Resource and Prospecting (China University of Petroleum, Beijing)) ;
  • Guang, Dong (Research Institute of Engineering and Technique, Huabei Sub-Company, SINOPEC)
  • Received : 2013.07.08
  • Accepted : 2013.09.22
  • Published : 2014.02.25

Abstract

In order to investigate the effect of different perforation angles (the angle between the perforation direction and the maximum horizontal principal stress) on the fracture initiation and propagation during hydraulic fracturing of highly deviated well in oil & gas saturated formation, laboratory experiments of the hydraulic fracturing had been carried out on the basis of non-dimensional similar criteria by using 400^3 $mm^3$ cement cubes. A plane fracture can be produced when the perforations are placed in the direction of the maximum horizontal principal stress. When the perforation angle is $45^{\circ}$, the fractures firstly initiate from the perforations at the upper side of the wellbore, and then turn to the maximum horizontal principal stress direction. When the well deviation angle and perforation angle are both between $45^{\circ}$ and $90^{\circ}$, the fractures hardly initiate from the perforations at the lower side of the wellbore. Well azimuth (the angle between the wellbore axis and the maximum horizontal principal stress) has a little influence on the fracture geometries; however it mainly increases the fracture roughness, fracture continuity and the number of secondary fractures, and also increases the fracture initiation and propagation pressure. Oriented perforating technology should be applied in highly deviated well to obtain a single plane fracture. If the well deviation angle is smaller, the fractures may link up.

Keywords

Acknowledgement

Supported by : National Science and Technology

References

  1. Abass, H.H. (1992), "Nonplanar fracture propagation from a horizontal wellbore: Experimental study", SPE J., 11(3), 133-137.
  2. Abass, H.H., Brumley, J.L. and Venditto, J.J. (1994), "Oriented perforations - a rock mechanics view", SPE Annual Technical Conference and Exhibition, New Orleans, LA, USA, September.
  3. Ahmed, U., Strawn, J. and Wilson, M. (1983), "Effect of stress distribution on hydraulic fracture geometry: A laboratory simulation study in one meter cubic blocks", SPE/DOE Low Permeability Gas Reservoirs Symposium, Denver, CO, USA, March.
  4. Akhaveissy, A.H., Desai, C.S., Mostofinejad, D. and Vafai, A. (2013), "FE analysis of RC structures using DSC model with yield surfaces for tension and compression", Comput. Concrete, Int. J., 11(2), 123-148. https://doi.org/10.12989/cac.2013.11.2.123
  5. Alshoaibi, A.M. (2010), "Finite element procedures for the numerical simulation of fatigue crack propagation under mixed mode loading", Struct. Eng. Mech., Int. J., 35(3), 283-299. https://doi.org/10.12989/sem.2010.35.3.283
  6. Beach, A. (1980), "Numerical models of hydraulic fracturing and the interpretation of syntectonic veins", J. Struct. Geol., 2(4), 425-438. https://doi.org/10.1016/0191-8141(80)90004-8
  7. Behrmann, L.A. and Elbel, J.L. (1991), "Effect of perforations on fracture initiation", J. Pet. Technol., 5, 608-615.
  8. Bunger, A.P., Jeffrey, R.G. and Detournay, J.E. (2005), "Application of scaling laws to laboratory-scale hydraulic fractures", Alaska Rocks 2005, The 40th U.S. Symposium on Rock Mechanics (USRMS): Rock Mechanics for Energy, Mineral and Infrastructure Development in the Northern Regions, Anchorage, AL, USA, June.
  9. Brumley, J.L. and Abass, H.H. (1996), "Hydraulic fracturing of deviated wells: Interpretation of breakdown and initial fracture opening pressure", SPE Eastern Regional Meeting, Columbus, OH, USA, October.
  10. Cao, Z.J. and Liu, Y.Y. (2012), "A new numerical modelling for evaluating the stress intensity factors in 3-D fracture analysis", Struct. Eng. Mech., Int. J., 43(3), 321-336. https://doi.org/10.12989/sem.2012.43.3.321
  11. Chen, Z., Bunger, A.P., Zhang, X. and Jeffrey, R.G. (2009), "Cohesive zone finite element-based modeling of hydraulic fractures", Acta Mechanica Solida Sinica, 22(05), 443-452. https://doi.org/10.1016/S0894-9166(09)60295-0
  12. Clifton, R.J. and Abou-Sayed, A.S. (1979), "On the computation of the three-dimensional geometry of hydraulic fractures", Symposium on Low Permeability Gas Reservoirs, Denver, CO, USA, May.
  13. Daneshy, A.A. (1973a), "A study of inclined hydraulic fractures", SPE J., 13(2), 61-68. https://doi.org/10.2118/4062-PA
  14. Daneshy, A.A. (1973b), "Experimental investigation of hydraulic fracturing through perforations", The 5th Annual Offshore Technology Conference, Houston, TX, USA, April.
  15. Daneshy, A.A. (1974), "Hydraulic fracture propagation in the presence of planes of weakness", SPE European Spring Meeting, Amsterdam, Netherlands, May.
  16. De Pater, C.J., Cleary, M.P., Quinn, T.S., Barr, D.T., Johnson, D.E. and Weijers, L. (1994), "Experimental verification of dimensional analysis for hydraulic fracturing", SPE Prod. Facil., 4, 230-238.
  17. Deng, J.G., Guo, X.M., Sun, Y., Qi, B. and Lei, W. (2008), "Research on oriented perforation optimization technique for fracturing wells in tight gas reservoir" Oil Drill. Prod. Tech., 6, 93-96. [In Chinese]
  18. Doe, T.W. and Boyce, G. (1989), "Orientation of hydraulic fractures in salt under hydrostatic and non-hydrostatic stresses", Int. J. Rock Mech. Min. Sci. Geomech. Abstr., 26(6), 605-605. https://doi.org/10.1016/0148-9062(89)91441-1
  19. EI Rabaa, W. (1989), "Experimental study of hydraulic fracture geometry initiated from horizontal wells", SPE Annual Technical Conference and Exhibition, San Antonio, TX, USA, October.
  20. Hallam, S.D. and Last, N.C. (1991), "Geometry of hydraulic fractures from modestly deviated wellbore", J. Pet. Technol., 43(6), 742-748 . https://doi.org/10.2118/20656-PA
  21. Hossain, M.M. and Rahman, M.K. (2008), "Numerical simulation of complex fracture growth during tight reservoir stimulation by hydraulic fracturing", J. Petrol. Sci. Eng., 60(2), 86-104. https://doi.org/10.1016/j.petrol.2007.05.007
  22. Kim, C.M. and Abass, H.H. (1991), "Hydraulic fracture initiation from horizontal wellbores: Laboratory experiments", Rock Mech. as a Multidiscip. Sci., Balkema, Rotterdam, Roegiers, July.
  23. Kim, W.-J., Lee, J.-M., Kim, J.-S. and Lee C.J. (2012), "Measuring high speed crack propagation in concrete fracture test using mechanoluminescent material", Smart Struct. Syst., Int. J., 10(6), 547-555. https://doi.org/10.12989/sss.2012.10.6.547
  24. King, G.E. (1989), "Perforating the horizontal well", J. Pet. Technol., 7, 671-672.
  25. Khristianovic, S.A. and Zheltov, Y.P. (1955), "Formation of vertical fractures by means of highly viscous liquid", Proceedings of the 4th World Petroleum Congress, Rome, Italy, June.
  26. Liao, F., Wang, W. and Chen. Y. (2012), "Parameter calibrations and application of micromechanical fracture models of structural steels", Struct. Eng. Mech., Int. J., 42(2),153-174. https://doi.org/10.12989/sem.2012.42.2.153
  27. Liu, G.H., Pang, F. and Chen, Z.X. (2000), "Development of scaling laws for hydraulic fracture simulation tests", J. Univ. Petrol., China (Edition of Natural Science), 5, 45-48. [In Chinese]
  28. Luo, X., Ge, H. and Ohashi, M. (2012), "Experimental study on ductile crack initiation in compact section steel columns", Steel Compos. Struct., Int. J., 13(4), 383-396. https://doi.org/10.12989/scs.2012.13.4.383
  29. Mack, M.G. and Warpinski, N.R. (2000), "Mechanics of hydraulic fracturing", (Economides, N. Eds., 3rd Edition), Reservoir Stimulation, Chichester, Wiley.
  30. Mahrer, K.D., Aud, W.W. and Hansen, J.T. (1996), "Far-field hydraulic fracture geometry: A changing paradigm", SPE Annual Technical Conference and Exhibition, Denver, CO, USA, October.
  31. Nagel, N.B. and Sanchez-Nagel, M. (2011), "Stress shadowing and microseismic events: A numerical evaluation", SPE Annual Technical Conference and Exhibition, Denver, CO, USA.
  32. Nagel, N.B., Sanchez-Nagel, M. and Lee, B. (2012), "Gas shale hydraulic fracturing: A numerical evaluation of the effect of geomechanical parameters", SPE Hydraulic Fracturing Technology Conference, The Woodlands, TX, USA.
  33. Nordgren, R.P. (1972), "Propagation of a vertical hydraulic fracture", SPE J., 4, 306-314.
  34. Pearson, C.M., Bond, A.J., Eck, M.E. and Schmldt, J.H. (1992), "Results of stress oriented and aligned perforating in fracturing deviated wells", J. Pet. Technol., 44(1), 10-18. https://doi.org/10.2118/22836-PA
  35. Pollard, D.D., Segall, P. and Delaney, P.T. (1982), "Formation and interpretation of dilatant echelon cracks", Geol. Soc. Am. Bull., 93(12), 1291-1303. https://doi.org/10.1130/0016-7606(1982)93<1291:FAIODE>2.0.CO;2
  36. Rahman, M.M., Hossain, M.M., Crosby, D.G., Rahman, M.K. and Rahman, S.S. (2002), "Analytical, numerical and experimental investigations of transverse fracture propagation from horizontal wells", J. Petrol. Sci. Eng., 35(3-4), 127-150. https://doi.org/10.1016/S0920-4105(02)00236-X
  37. Siebrits, E. and Peirce, A.P. (2002), "An efficient multi-layer planar 3D fracture growth algorithm using a fixed mesh approach", Int. J. Numer. Meth. Eng., 53(3), 691-717. https://doi.org/10.1002/nme.308
  38. Sneddon, I.N. and Elliott, H.A. (1946), "The opening of a Griffith crack under internal pressure", Q. Appl. Math., 3, 262-267.
  39. Soliman, M.Y., East, L. and Adams, D. (2008), "Geomechanics aspects of multiple fracturing of horizontal and vertical wells", SPE Drill. Completion, 23(3), 217-228. https://doi.org/10.2118/86992-PA
  40. Stadulis, J.M. (1995), "Development of a completion design to control screenouts caused by multiple near-wellbore fractures", SPE Rocky Mountain Regional / Low Permeability Reservoirs Symposium, Denver, CO, USA, March.
  41. Tada, H., Paris, P.C. and Irwin, G.R. (1985), "The stress analysis of cracks handbook", Louis, MO, USA.
  42. Tang, C.A., Tham, L.G., Lee, P.K.K., Yanga, T.H. and Lia, L.C. (2002), "Coupling analysis of flow, stress and damage (FSD) in rock failure", Int. J. Rock Mech. Min. Sci., 39(4), 477-489. https://doi.org/10.1016/S1365-1609(02)00023-0
  43. van de Ketterij, R.G., de Pater, C.J. (1997), "Experimental study on the impact of perforations on hydraulic fracturing tortuosity", SPE European Formation Damage Conference, Hague, The Netherlands, June.
  44. Weijers, L. and De Pater, C.J. (1992), "Facture reorientation in model tests", SPE Formation Damage Control Symposium, Lafayette, LA, USA, February.
  45. Weng, X.W. (1993), "Fracture initiation and propagation from deviated wellbores", SPE Annual Technical Conference and Exhibition, Houston, TX, USA, October.
  46. Zhang, G.M., Liu, H., Zhang, J., Wu, H.A. and Wang, X.X. (2010), "Three-dimensional finite element simulation and parametric study for horizontal well hydraulic fracture", J. Petrol. Sci. Eng., 72(3-4), 310-317. https://doi.org/10.1016/j.petrol.2010.03.032
  47. Zhang, G.Q., Chen, M. and Zhao Y.B. (2008), "Study on initiation and propagation mechanism of fracturesin oriented perforation of new wells", Acta petrol ei sinica, 29(1), 117-119. [In Chinese]
  48. Zhang, X, Jeffrey, R.G. and Thiercelin, M. (2007), "Deflection and propagation of fluid-driven fractures at frictional bedding interfaces: A numerical investigation", J. Struct. Geol., 29(3), 396-410. https://doi.org/10.1016/j.jsg.2006.09.013
  49. Zhang, X., Jeffrey, R.G. and Thiercelin, M. (2009), "Mechanics of fluid-driven fracture growth in naturally fractured reservoirs with simple network geometries", J. Geophys. Res. - Sol d Earth, 114(B12), 402-406.
  50. Zhou, J., Jin, Y. and Chen, M. (2010), "Experimental investigation of hydraulic fracturing in random naturally fractured blocks", Int. J. Rock Mech. Min. Sci., 47, 1193-1199. https://doi.org/10.1016/j.ijrmms.2010.07.005
  51. Zhu, X.H., Liu, S.H., Tong, H. and Liu, Y.H. (2012), "Experimental and numerical study of drill pipe erosion wear in gas drilling", Eng. Fail. Anal., 26, 370-380. https://doi.org/10.1016/j.engfailanal.2012.06.005
  52. Zhu, H.Y., Deng, J.G., Li, S.Y., Chen, Z.J., Yan, W., Hu, L.B., Lin, H. and Yan, C.L. (2013), "Numerical simulation and laboratory experiments of hydraulic fracturing of highly deviated well", Applied Mechanics and Materials, 275-277, 278-281. https://doi.org/10.4028/www.scientific.net/AMM.275-277.278
  53. Zhu, H.Y., Deng, J.G., Xie, Y.H., Huang, K.W., Zhao, J.Y. and Yu, B.H. (2012), "Rock mechanics characteristic of complex formation and faster drilling techniques in Western South China Sea oilfields", Ocean Eng., 44, 33-45. https://doi.org/10.1016/j.oceaneng.2012.01.031

Cited by

  1. Borehole stability analysis in oil and gas drilling in undrained condition vol.7, pp.5, 2014, https://doi.org/10.12989/gae.2014.7.5.553
  2. Hydraulic Fracture Initiation and Propagation from Wellbore with Oriented Perforation vol.48, pp.2, 2015, https://doi.org/10.1007/s00603-014-0608-7
  3. Stress field interference of hydraulic fractures in layered formation vol.9, pp.5, 2015, https://doi.org/10.12989/gae.2015.9.5.645
  4. A new geomechanical approach to investigate the role of in-situ stresses and pore pressure on hydraulic fracture pressure profile in vertical and horizontal oil wells vol.7, pp.3, 2014, https://doi.org/10.12989/gae.2014.7.3.233
  5. Laboratory hydraulic fracturing test on large-scale pre-cracked granite specimens vol.44, 2017, https://doi.org/10.1016/j.jngse.2017.03.037
  6. Coupled flow-stress-damage simulation of deviated-wellbore fracturing in hard-rock vol.26, 2015, https://doi.org/10.1016/j.jngse.2015.07.007
  7. Macroscale Mechanical and Microscale Structural Changes in Chinese Wufeng Shale With Supercritical Carbon Dioxide Fracturing 2017, https://doi.org/10.2118/181369-PA
  8. Fracture Characteristics and Change of Permeability Under the Influence of Natural Fractures: Experimental Study of Wufeng-Longmaxi Shale vol.21, pp.2, 2018, https://doi.org/10.2118/181842-pa
  9. Numerical Investigation on Rock-Fracturing Mechanism by Using Splitter under Hole Assistance vol.2019, pp.None, 2014, https://doi.org/10.1155/2019/4395729
  10. An experimental study on the hydraulic fracturing of radial horizontal wells vol.17, pp.6, 2014, https://doi.org/10.12989/gae.2019.17.6.535
  11. Higher-order simulation of two-phase compositional flow in 3D with non-planar fractures vol.402, pp.None, 2014, https://doi.org/10.1016/j.jcp.2019.108896
  12. Fracability Evaluation Method and Influencing Factors of the Tight Sandstone Reservoir vol.2021, pp.None, 2014, https://doi.org/10.1155/2021/7092143
  13. Research on multi-frequency ultrasonic scanning detecting technology of cavity in the test borehole vol.80, pp.2, 2014, https://doi.org/10.1007/s10064-020-01979-5
  14. Simulation of hydraulic fracturing and Darcy fluid flow in a porous medium using a coupled Discrete Element Method with fluid flow vol.204, pp.None, 2014, https://doi.org/10.1016/j.petrol.2021.108706
  15. Multiple hydraulic fractures growth from a highly deviated well: A XFEM study vol.208, pp.no.pd, 2014, https://doi.org/10.1016/j.petrol.2021.109709