Journal of the Korean Society of Safety (한국안전학회지)

The Korean Society of Safety (한국안전학회)
권호 표지
DOI QR코드

DOI QR Code

Fatigue Characteristics on Welded Joint of Gear Box-Shank in Vibro Ripper for Rock Crash

암반 파쇄용 진동리퍼 기어박스-생크 용접부의 피로특성

  • Oh, K.K. (Department of Mechanical Design Engineering, Chungnam National University) ;
  • Kim, Jaehoon (Department of Mechanical Design Engineering, Chungnam National University) ;
  • Kim, Y.W. (Department of Mechanical Design Engineering, Chungnam National University) ;
  • Park, J.Y. (DaeDong Engineering Co., Ltd.) ;
  • Yang, G.S. (DaeDong Engineering Co., Ltd.) ;
  • Park, J.W. (Korea Institute of Machinery & Materials) ;
  • Kim, S.H. (Korea Institute of Machinery & Materials)
  • Received : 2014.09.29
  • Accepted : 2014.12.10
  • Published : 2014.12.31
Download PDF
⟨ Previous Next ⟩

Abstract

Vibro ripper worked by high frequency vibration is developed to do rock fragmentation and work of ripper is the different concept with other existing breakers. The gear box-shank welded joint of vibro ripper is very important part to deliver vibromotive force to tooth, so this part should endure high frequency vibration environments. The purposes of this study are to choose the optimal welding conditions for fatigue strength. The conditions were made using three kind of shank materials and two kind of filler metals. Shank materials are Hadox-hituf, Posten80 and AR400, and filler metals are CSF-71T and CSF-81T. The fatigue test was conducted each condition. Fracture surface was observed to estimate fracture characteristics of welded joint using SEM.

Keywords

References

  1. J. H. Lee, J. G. Ih, S. H. Park, T. G. Ha and J. H. Lim, "Vibro-acoustic Design and Developement of a Low-noise Hydraulic Breaker", Journal of the Korean Society for Noise and Vibration Engineering, Vol. 11, No. 5, pp. 148-155, 2001.
  2. G. B. Park, C. H. Park, Y. S. Park and D. H. Choi, "Optimal Design of Minimizing Weight of Housing of Hydraulic Breaker", Trans. of the Korean Society of Mechanical Engineers(A), Vol.35, No. 2, pp 207-212, 2011. https://doi.org/10.3795/KSME-A.2011.35.2.207
  3. V. Balasubramanian and B. Guha, "Influence of Weld Size Fatigue Crack Growth Characteristics of Flux Cored are Welded Cruciform Joints", Materials Science and Engineering: A", Vol. 265, Issues 1-2, pp.7-17, 1999. https://doi.org/10.1016/S0921-5093(99)00007-6
  4. Y. B. Lee, "A Study on Characteristics of Fatigue Life in LOP Cruciform Rillet Welding Zone", Journal of the Korean Institute of Gas, Vol. 16, No. 3, pp.29-34, 2012.
  5. K. H. Chang and C. H. Lee, "Residual Stresses and Fracture Mechanics Analysis of a Crack in Welds of High Strength Steels", Engineering Fracture Mechanics, Vol. 74, Issue 6, pp. 980-994, 2007. https://doi.org/10.1016/j.engfracmech.2006.08.012
  6. S. B. Jeon, "Fracture Surface Analysis", R&B INC., No. RB-FA-G003, 2014.
  7. Z. Xiaohui, W. Dongpo, D. Caiyan, L. Yu and S. Zongxian, "The Fatigue Behaviors of Butt Welds Ground Flush in the Super-long Life Regime", International Journal of Fatigue, Vol. 36, Issue 1, pp. 1-8, 2012. https://doi.org/10.1016/j.ijfatigue.2011.09.009
  8. F. Matsuda, H. Nakagawa, S. Ogata and S. Katayama, "Fractographic Investigation on Solidification Crack in the Varestraint Test of Fully Austenitic Stainless steel : Studies on Fractography of Welded Zone(III)",Transactions of JWRI, Vol. 7, No.1, pp.59-70, 1978.