Journal of Korean Tunnelling and Underground Space Association (한국터널지하공간학회 논문집)

Korean Tunnelling and Underground Space Association (한국터널지하공간학회)
권호 표지
DOI QR코드

DOI QR Code

Performance estimation of conical picks with slim design by the linear cutting test (II): depending on skew angle variation

선형절삭시험에 의한 슬림 코니컬커터의 절삭성능 평가(II): Skew Angle 변화에 의한 결과

  • Choi, Soon-Wook (Geotechnical Engineering Research Division, Korea Institute of Construction Technology) ;
  • Chang, Soo-Ho (Geotechnical Engineering Research Division, Korea Institute of Construction Technology) ;
  • Lee, Gyu-Phil (Geotechnical Engineering Research Division, Korea Institute of Construction Technology) ;
  • Park, Young-Taek (Geotechnical Engineering Research Division, Korea Institute of Construction Technology)
  • 최순욱 (한국건설기술연구원 SOC성능연구소 Geo-인프라연구실) ;
  • 장수호 (한국건설기술연구원 SOC성능연구소 Geo-인프라연구실) ;
  • 이규필 (한국건설기술연구원 SOC성능연구소 Geo-인프라연구실) ;
  • 박영택 (한국건설기술연구원 SOC성능연구소 Geo-인프라연구실)
  • Received : 2014.11.13
  • Accepted : 2014.11.24
  • Published : 2014.11.28
Download PDF
⟨ Previous Next ⟩

Abstract

In this study, the cutter acting forces were measured by 3-directional load cell at two different skew angles and various S/d ratios during a series of linear cutting tests using a slim conical pick. The analysis for cutting performance were carried out after calculating average values of the measured results. The increase of penetration depth results in the decrease of specific energy. And the variations of the cutter acting forces depending on penetration depth in the case of 6 degree skew angle were smaller than in the case of 0 degree skew angle. From this results, 6 degree skew angle is more effective than 0 degree skew angle in designing optimal specifications of cutting head. In addition, $F_c/F_n$ under the setting of 6 degree skew angle was smaller than under the setting of 0 degree skew angle. However, it should be considered that the increase of cutter acting force in the cutting direction accompanied the increase of driving force in the case of the setting for 6 degree skew angle.

본 연구에서는 받음각이 $45^{\circ}$인 경우에 대해 사각이 $0^{\circ}$와 $6^{\circ}$이고 S/d비가 1.3~12사이인 시험조건에 대해 슬림 코니컬커터를 사용하여 선형절삭시험동안 발생하는 커터작용력을 측정하였다. 각 시험조건에서 커터작용력인 연직력, 절삭력, 구동력을 측정하였고 그 측정결과의 평균값을 사용하여 분석을 실시하였다. 커터관입깊이가 깊어질수록 비에너지가 감소하였고 커터관입깊이에 따른 커터작용력의 변화는 사각이 $6^{\circ}$인 경우가 작게 나타났다. 이와 같은 결과로부터 사각이 $6^{\circ}$인 경우가 $0^{\circ}$인 경우에 비해 장비설계측면에서 효과적인 것으로 판단된다. 또한 $F_c/F_n$은 사각이 $6^{\circ}$일 때가 $0^{\circ}$인 경우에 비해 작게 나타났다. 그러나 사각이 있을 경우 구동력의 증가가 나타날 수 있으므로 이에 대한 고려가 필요하다.

Keywords

References

  1. Asbury, B., Cigla, M., Balci, C. (2002), "Design methodology, testing and evaluation of a continuous miner cutterhead for dust reduction in underground coal mining", 2002 SME Annual Meeting, February 25-27, Phoenix, Arizona, pp. 1-8.
  2. Balci, C., Demircin, M.A., Copur, H., Tuncdemir, H. (2004), "Estimation of optimum specific energy based on rock properties for assessment of roadheader performance", The Journal of The South African Institute of Mining and Metallurgy, December 2004, pp. 633-642.
  3. Bilgin, N., Kuzu, C., Eskikaya, S. (1997), "Cutting performance of rock hammers and roadheaders in Istanbul Metro drivages", Proceedings, Word Tunnel Congress'97, Tunnels for People, Balkema, pp. 455-460.
  4. Copur, H., Balci, C., Tumac, D., Bilgin, N. (2011), "Field and laboratory studies on natural stones leading to empirical performance prediction of chain saw machines", International Journal of Rock Mechanics & Mining Sciences, Vol. 48, pp. 269-282. https://doi.org/10.1016/j.ijrmms.2010.11.011
  5. Chang, S.H., Choi, S.W., Park, Y.T., Lee, G.P., Bae, G.J. (2012), "Characterization of the deformation of a disc cutter in linear rock cutting test", J. of Korean Tunn. Undergr. Sp. Assoc., Vol. 14, No. 3, pp. 197-213. https://doi.org/10.9711/KTAJ.2012.14.3.197
  6. Choi, S.W., Chang, S.H., Park, Y.T., Lee, G.P., Bae, G.J. (2013), "A experimental study on the loads and temperature acting on the shaft of a disc cutter during linear rock cutting test", J. of Korean Tunn. Undergr. Sp. Assoc., Vol. 15, No. 3, pp. 237-251. https://doi.org/10.9711/KTAJ.2013.15.3.237
  7. Choi, S.W., Chang, S.H., Park, Y.T., Lee, G.P., Bae, G.J. (2014), "Comparative analysis of cutter acting forces and axial stresses of single and double disc cutters by linear cutting test", J. of Korean Tunn. Undergr. Sp. Assoc., Vol. 16, No. 2, pp. 181-191. https://doi.org/10.9711/KTAJ.2013.16.2.181
  8. Fowell, R.J., OCHEI, N.N. (1984), "A comparison of dust make and energy requirements for rock cutting tools", International Journal of Mining Engineering, Vol. 2, pp. 73-83. https://doi.org/10.1007/BF00880859
  9. Gertsch, R., Gertsch, L., Rostami, J. (2007), "Disc cutting tests in colorado red granite: implications for TBM performance prediction", International Journal of Rock Mechanics & Mining Sciences, Vol. 44, pp. 238-246. https://doi.org/10.1016/j.ijrmms.2006.07.007
  10. Goktan, R.M., Gunes, N. (2005), "A semi-empirical approach to cutting force prediction for pointattack picks", The Journal of The South African Institute of Mining and Metallurgy, Vol. 105, April 2005, pp. 257-264.
  11. Hurt, K.G., Evans, I. (1981), "Point attack tools: an evaluation of function and use for rock cutting", Mining Engineer, Vol. 140, pp. 673-675.
  12. Kim, E., Rostami, J., Swope, C. (2012), "Full scale linear cuttting experiment to examine conical bit rotation", Journal of Mining Science, Vol. 48, No. 5, pp. 882-895. https://doi.org/10.1134/S1062739148050139
  13. Nilsen, B., Ozdemir, L. (1993), "Hard rock tunnel boring prediction and field performance", Proc. of Rapid Excavation and Tunneliing Coference (RETC), pp. 833-852.
  14. Rostami, J., Ozdemir, L., Neil, D.M. (1994), "Application of heavy duty roadheaders for underground development of the yucca mountain exploratory study facility, high level radioactive waste management", Proceedings of the 5th Annual international conference, Vol. 2, pp. 395-402.
  15. Rostami, J. (2013), "Cutterhead design procedures and performance evaluations for roadheader, final report submitted to korea institute of construction technology", August 2013, Jamal Rostami Engineering Services LLC.
  16. Tunnel Business Magazine (2011), "Roadheaders in hard rock-east side access among north american projects employing roadheader technology", February 2011, pp. 20-21.

Cited by

  1. Cutting head attachment design for improving the performance by using multibody dynamic analysis vol.17, pp.3, 2016, https://doi.org/10.1007/s12541-016-0046-4
  2. A new linear cutting machine for assessing the rock-cutting performance of a pick cutter vol.88, 2016, https://doi.org/10.1016/j.ijrmms.2016.07.021
  3. Automation for Pick Arrangement Design of a Cutting Head Attachment Using RecurDyn/ProcessNet vol.40, pp.7, 2016, https://doi.org/10.3795/KSME-A.2016.40.7.685
  4. Performance estimation depending on the insert size of conical picks by linear cutting test vol.18, pp.2, 2016, https://doi.org/10.9711/KTAJ.2016.18.2.221
  5. Performance Evaluation of Conical Picks for Roadheader in Copper Mines vol.25, pp.6, 2015, https://doi.org/10.7474/TUS.2015.25.6.496