DOI QR코드

DOI QR Code

Comparison of shear lag in structural steel building with framed tube and braced tube

  • Mazinani, Iman (Department of Civil Engineering, University of Malaya) ;
  • Jumaat, Mohd Zamin (Department of Civil Engineering, University of Malaya) ;
  • Ismail, Z. (Department of Civil Engineering, University of Malaya) ;
  • Chao, Ong Zhi (Department of Mechanical Engineering, University of Malaya)
  • 투고 : 2012.08.09
  • 심사 : 2013.12.09
  • 발행 : 2014.02.10

초록

Under lateral loads Framed Tube (FT) system exhibits reduction of cantilever efficiency due to the effect of shear lag. Braced Tube (BT) represents a valuable solution to overcome shear lag problems by stiffening the exterior frame with diagonal braced members. This study investigates the effect of shear lag on BT and FT under wind load. Shear lag and top-level displacement results are compared with previous findings by researchers on FT and BT systems. The investigation of the effect of various configurations in BT on the reduction the shear lag is another objective of this study. The efficiency of each structure is evaluated using the linear response spectrum analysis to obtain shear lag. STADD Pro software is used to run the dynamic analysis of the models. Results show there is relatively less shear lag in all the BT configurations compared to the FT structural system. Moreover, the comparison of the obtained result with those derived by previous studies shows that shear lag is not proportional to lateral displacement. With respect to results, optimum BT configuration in term of lower shear lag caused by lateral loads is presented.

키워드

참고문헌

  1. Ali, M.M. and Moon, K.S. (2007), "Structural developments in tall buildings: current trends and future prospects", Arch. Sci. Rev., 50(3), 205-223. https://doi.org/10.3763/asre.2007.5027
  2. ASCE (2005), Minimum design loads for buildings and other structures, Amer Society of Civil Engineers.
  3. Carpinteri, A., Lacidogna, G. and Puzzi, S. (2010) "A global approach for three dimensional analysis of tall buildings", Struct. Des. Tall Spec. Build., 19(5), 518-536.
  4. Carpinteri, A., Corrado, M., Lacidogna, G. and Cammarano, S. (2012). "Lateral load effects on tall shear wall structures of different height", Struct. Eng. Mech., 41(3), 313-337. https://doi.org/10.12989/sem.2012.41.3.313
  5. Chang, S.T. and Zheng, F.Z. (1987), "Negative shear lag in cantilever box girder with constant depth", J. Struct. Eng., 113, 20-35. https://doi.org/10.1061/(ASCE)0733-9445(1987)113:1(20)
  6. Chok, K. (2004), "Lateral systems for tall buildings", Master's Thesis, Massachusetts Institute of Technology, Massachusetts.
  7. Coull, A. and Subedi, N.K. (1971), "Framed-tube structures for high-rise buildings", J. Struct. Div., 91(8), 2097-2105.
  8. Foutch, D.A. and Chang, P.C. (1982), "A shear lag anomaly", J. Struct. Div., 108(7), 1653-1658.
  9. Iyengar, H. (2000), "Reflections on the Hancock Concept", CTBUH Review, 1, 44.
  10. Khan, F.R. (1972), "Future of high rise structures", Progressive Architecture, October, 17-19.
  11. Khan, F.R. (1983), "100 storey John Hancock center, Chicago: a case study of the design process", Eng. Struct., 5(1), 10-14. https://doi.org/10.1016/0141-0296(83)90035-4
  12. Kim, J., Park, J., Shin, S.W. and Min, K.W. (2009), "Seismic performance of tubular structures with buckling restrained braces", Struct. Des. Tall Spec. Build., 18(4), 351-370. https://doi.org/10.1002/tal.420
  13. Leonard, J. (2007), "Investigation of shear lag effect in high-rise buildings with diagrid system", Master's Thesis, Massachusetts Institute of Technology, Massachusetts.
  14. Mazinani, I. (2011), "Framed diagonalized tube system for high rise buildings", Master's Thesis, Faculty of Engineering, University of Malaya, Kuala Lumpur, Malaysia.
  15. Moon, K.S. (2010), "Stiffness-based design methodology for steel braced tube structures: a sustainable approach", Eng. Struct., 32(10), 3163-3170. https://doi.org/10.1016/j.engstruct.2010.06.004
  16. Mahjoub, R., Rahgozar, R. and Saffari, H. (2011), "Simple method for analysis of tube frame by consideration of negative shear lag", Austr. J. Basic Appl. Sci., 5(3), 309-316.
  17. Rahgozar, R., Ahmadi, A.R.H.O. and Malekinejad, M. (2011), "A simple mathematical model for static analysis of tall buildings with two outrigger-belt truss systems", Struct. Eng. Mech., 40(1), 65-84. https://doi.org/10.12989/sem.2011.40.1.065
  18. Singh, Y. and Nagpal, A.K. (1994), "Negative shear lag in framed-tube buildings", J. Struct. Eng., 120(11), 3105-3121. https://doi.org/10.1061/(ASCE)0733-9445(1994)120:11(3105)
  19. Taranath, B.S. (1998), Steel, Concrete, and Composite Design of Tall Buildings, McGraw-Hill, USA.
  20. Zahiri-Hashemi, R., Kheyroddin, A. and Farhadi, B. (2013), "Effective number of mega-bracing, in order to minimize shear lag", Struct. Eng. Mech., 48(2), 173-193. https://doi.org/10.12989/sem.2013.48.2.173

피인용 문헌

  1. An Overview of Tsunami Wave Force on Coastal Bridge and Open Challenges vol.09, pp.02, 2015, https://doi.org/10.1142/S1793431115500062
  2. Effect of Span Length on Behavior of MRF Accompanied with CBF and MBF Systems vol.171, 2017, https://doi.org/10.1016/j.proeng.2017.01.431
  3. Using local stiffness indicator to examine the effect of honeycombs on the flexural stiffness of reinforced concrete beams vol.64, 2015, https://doi.org/10.1016/j.measurement.2014.12.051
  4. Shear lag effects on wide U-section pre-stressed concrete light rail bridges vol.68, pp.1, 2014, https://doi.org/10.12989/sem.2018.68.1.067
  5. The Effect of Lateral Load Type on Shear Lag of Concrete Tubular Structures with Different Plan Geometries vol.10, pp.10, 2020, https://doi.org/10.3390/cryst10100897
  6. Parametric Analysis of the Shear Lag Effect in Tube Structural Systems of Tall Buildings vol.11, pp.1, 2014, https://doi.org/10.3390/app11010278
  7. Investigation of shear lag effect in tall tube-type buildings vol.34, pp.None, 2014, https://doi.org/10.1016/j.istruc.2021.10.035