DOI QR코드

DOI QR Code

An experimental study on the flexural performance of laminated glass

  • Huang, Xiaokun (Research and Development, China Academy of Building Research) ;
  • Liu, Gang (Research and Development, China Academy of Building Research) ;
  • Liu, Qiang (Research and Development, China Academy of Building Research) ;
  • Bennison, Stephen J. (E.I. DuPont de Nemours & Co. Inc.)
  • Received : 2013.08.26
  • Accepted : 2013.12.12
  • Published : 2014.01.25

Abstract

This paper reported an experimental study on creep behaviors of PVB and Ionoplast laminated glass (LG) under load duration of 30 days. The tests were carried out in room temperature ($23^{\circ}C$). The study revealed that after sustaining loads for 30 days, the mid-span deflection of PVB LG increased by almost 102% compared with its short term deflection, while that of Ionoplast LG approximately increased by 14%; composite effects between two glass plies in PVB LG gradually reduced with time, but did not fully vanish at the 30th day; two glass plies in Ionoplast LG on the other hand was able to withstand loads as an effective composite section during the entire loading period; the creep behaviors of both LG were not finished yet at the 30th day. In addition to this, also studied was the varying of the bending stresses of PVB and Ionoplast LG under load duration of 2 hours. The tests were carried out in ambient temperatures of $30^{\circ}C$, $50^{\circ}C$ and $80^{\circ}C$ respectively. It was found that under a given load, although the bending stresses of both LG increased with increasing temperature, for PVB LG the increasing rate of the bending stress decreased with increasing temperature, while for Ionoplast LG the increasing rate of the bending stress increased with increasing temperature.

Keywords

References

  1. Allel, M., Mohamed, A. and Ahmed, B. (2013), "Stability condition for the evaluation of damage in three-point bending of a laminated composite", Steel Compos. Struct., 15(2), 203-220. https://doi.org/10.12989/scs.2013.15.2.203
  2. ASTM E1300-09a (2009), Standard practice for detennining load resistance of glass in buildings, New York.
  3. Bati, S.B., Ranocchiai, G., Reale, C. and Rovero, L. (2010), "Time-dependent behavior of laminated glass", J. Mater. Civ. Eng., 22(4), 389-396. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000032
  4. Behr, R.A., Minor, J.E. and Linden, M.P. (1986), "Load duration and interlayer thickness effects on laminated glass", J. Struct. Eng., 112(6), 1441-1453. https://doi.org/10.1061/(ASCE)0733-9445(1986)112:6(1441)
  5. Behr, R.A., Minor, J.E. and Norville, H.S. (1993), "Structural behavior architectural LG", J. Struct. Eng., 119(1), 202-222. https://doi.org/10.1061/(ASCE)0733-9445(1993)119:1(202)
  6. Bennison, S.J., Davies, P.S., Van Duser, A. and Jagota, A. (2001), "Structural performance of laminated safety glass made with 'stiff' interlayers", Proceedings of Glass Performance Days, Tampere, Finland, June.
  7. Callaghan, J.O. (2012), "Adventures with structural glass", Proceedings of Glass Performance Days, Sao Paulo, Brazil, June.
  8. Callewaert, D., Belis, J., Delince, D. and Impe, R.V. (2012), "Experimental stiffness characterisation of glass/ionomer laminates for structural applications", Constr. Build. Mater., 37, 685-692. https://doi.org/10.1016/j.conbuildmat.2012.07.035
  9. Ferry, J.D. (1980), Viscoelastic Properties of Polymers, (3rd Edition), John Wiley & Sons, New York, USA
  10. JGJ 102-2003 (2003), Technical code for glass curtain wall engineering, Beijing.
  11. Ledbetter, S.R., Walker, A.R. and Keiller, A.P. (2006), "Structural use of glass", J. Archit. Eng., 12(3), 137-149. https://doi.org/10.1061/(ASCE)1076-0431(2006)12:3(137)
  12. prEN 13474-1 (1999), Glass in building-design of glass panes-part1: General basis of design, London.
  13. prEN 16612 (2013). Glass in building-determination of the load resistance of glass panes by calculation and testing, London.
  14. Rezaiee-Pajand, M., Shahabian, F. and Tavakoli, F.H. (2012), "A new higher-order triangular plate bending element for the analysis of laminated composite and sandwich plates", Struct. Eng. Mech., 43(2), 253-271. https://doi.org/10.12989/sem.2012.43.2.253
  15. Yin, Y.W., Zhang, Q.L. and Huang, Q.W. (2004), "Experimental study on load bearing capacity of point-supported mid-hollow and laminated glasses", J. Build Struct., 25(1), 93-98.

Cited by

  1. Influence of Interlayers on the Flexural Performance of Four-Side Supported Laminated Glass at Room Temperature vol.18, pp.1, 2015, https://doi.org/10.1260/1369-4332.18.1.33
  2. The flexural performance of laminated glass beams under elevated temperature vol.52, pp.3, 2014, https://doi.org/10.12989/sem.2014.52.3.603
  3. Biaxial creep property of ethylene tetrafluoroethylene (ETFE) foil vol.54, pp.5, 2015, https://doi.org/10.12989/sem.2015.54.5.973
  4. Experimental investigation of multi-layered laminated glass beams under in-plane bending vol.60, pp.5, 2016, https://doi.org/10.12989/sem.2016.60.5.781
  5. Comparison of viscoelastic finite element models for laminated glass beams vol.131-132, 2017, https://doi.org/10.1016/j.ijmecsci.2017.05.035
  6. 3D Adaptive Combined DE/FE Algorithm for Analyzing Impact Fracture of Laminated Glass pp.1793-6969, 2019, https://doi.org/10.1142/S0219876218501013