동력기계공학회지 (Journal of Power System Engineering)

  • 제18권6호
  • /
  • Pages.153-158
  • /
  • 2014
  • /
  • 2713-8429(pISSN)
  • /
  • 2713-8437(eISSN)
한국동력기계공학회 (The Korean Society for Power System Engineering)
권호 표지
DOI QR코드

DOI QR Code

A Study on a High Efficiency Dryer for Food Waste

  • Kim, Bum-Suk (Faculty of Wind Energy Engineering, Jeju National University) ;
  • Kang, Chang-Nam (Department of Mechanical Engineering, Jeju National University) ;
  • Jeong, Ji-Hyun (Department of Mechanical Engineering, Jeju National University)
  • 투고 : 2014.10.27
  • 심사 : 2014.12.02
  • 발행 : 2014.12.31
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

The food waste that occurs in one year is very high in our country and disposal is expensive. However, disposers for food waste are not used wisely at real life. This is because most of them some kind of problem, for example big volume, complicated construction, high cost, lots of troubles, low energy efficiency and so on. In this study, we propose the new dryer system to decrease drying times by injecting hot air in down the side of the drying bucket. The designed drying bucket has inclined inlet holes down both sides. The inlet holes have variable gradients, we adjust the inlet velocity of the hot air to find a suitable vortex in the drying bucket. We verify the properties of the proposed system though simulation. The results show the proposed dryer system can improve the drying time and save energy for food waste disposal.

키워드

참고문헌

  1. Y. B. Kim and J. H. Jeong, 2014, "Development of Anti-Seasickness Bed used in Vessel", Journal of the Korean Society for Power System Engineering, Vol. 18, No. 4, pp. 112-116. https://doi.org/10.9726/kspse.2014.18.4.112
  2. D. W. Jung, S. H. Park and J. H. Jeong, 2013, "Forming Analysis for Optimization of 18 Stage Roll Forming Process", Journal of the Korean Society for Power System Engineering, Vol. 17, No. 3, pp. 65-71. https://doi.org/10.9726/kspse.2013.17.3.065
  3. D. W. Jung, E. S. Jang, J. H. Jeong, K. I. Noh and J. H. Son, 2013, "Evaluation for Manufacturing Stabilization of an Architecture Insulating Material", Advanced Materials Research, Vol. 716, pp. 575-580. https://doi.org/10.4028/www.scientific.net/AMR.716.575
  4. D. W. Jung, J. H. Jeong, S. M. Woo, E. S. Jang, K. J. Park and J. H. Son, 2013, "A Study on the Stability of a Vehicle with Lifting Utility", Advanced Materials Research, Vol. 753, pp. 1169-1174.
  5. O. Martin, L. Hansen and J. Johansen, 2004, "Tip Studies Using CFD and Comparison with Tip Loss Models", Wind Energy, Vol. 7, pp. 343-356. https://doi.org/10.1002/we.126
  6. J. Martinez, L. Bernabini, O. Probst and C. Rodriguez, 2005, "An Improved BEM Model for the Power Curve Prediction of Stall-regulated Wind Turbines", Transactions of the Korean Society of Machine Tool Engineers", Wind Energy, Vol. 8, pp. 385-402. https://doi.org/10.1002/we.147

피인용 문헌

  1. Development of Ventilator without Power using Air Flow vol.20, pp.2, 2016, https://doi.org/10.9726/kspse.2016.20.2.026
  2. A study on Forming Analysis for Copper Pipe Bending Process Improvement vol.22, pp.3, 2018, https://doi.org/10.9726/kspse.2018.22.3.060
  3. 무용접 후렉시블 조인트 개발에 관한 기초연구 vol.21, pp.1, 2014, https://doi.org/10.9726/kspse.2017.21.1.057
  4. 냉풍 건조 시스템의 배플 배열각도 및 공기공급관 위치 변화에 따른 성능 향상에 관한 연구 vol.21, pp.4, 2014, https://doi.org/10.9726/kspse.2017.21.4.062