동력기계공학회지 (Journal of Power System Engineering)

  • 제18권6호
  • /
  • Pages.34-39
  • /
  • 2014
  • /
  • 2713-8429(pISSN)
  • /
  • 2713-8437(eISSN)
한국동력기계공학회 (The Korean Society for Power System Engineering)
권호 표지
DOI QR코드

DOI QR Code

석탄 분쇄기용 유성감속기 케이싱의 거동에 관한 유한요소해석

Finite Element Analysis for the Behavior of the Casing of a Pulverizer Mill Planetary Gear Reducer

  • 서지환 (부경대학교 대학원 기계설계공학과) ;
  • 김선진 (부경대학교 기계자동차공학과) ;
  • 정민화 ((주)성일하이테크 기술연구소) ;
  • 김병탁 (부경대학교 기계자동차공학과)
  • Seo, Ji-Hwan (Department of Mechanical Design Engineering, Graduate School, Pukyong National University) ;
  • Kim, Seon-Jin (Department of Mechanical & Automotive Engineering, Pukyong National University) ;
  • Jung, Min-Hwa (R&D Center, Sungil Hi-Tech Co., Ltd.) ;
  • Kim, Byung-Tak (Department of Mechanical & Automotive Engineering, Pukyong National University)
  • 투고 : 2014.08.04
  • 심사 : 2014.10.31
  • 발행 : 2014.12.31
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

In this study, the structural analysis and the modal analysis are conducted to investigate the stress level, the deformation characteristics and the natural modes of the casing of a planetary gear reducer for a 800kW grade pulverizer mill. The casing is subjected to the load, 2800 kN, from the lump coals in the pulverizing process. Because of the symmetry, the half portion of the reducer casing is modeled for the stress analysis. But the full model is used to find out the eigenvalues and natural modes for the modal analysis. The contact conditions are applied between the thrust pad bearing and the adjacent contacting parts. The results shows that the casing structure has the sufficient strength and stiffness to support the load under consideration. ANSYS version 15 is employed to perform the numerical study.

키워드

참고문헌

  1. H. B. Shin, X. L. Li, I. Y. Jeong, J. M. Park and S. Y. Lee, 2009, "Modeling and Parameter Identification of Coal Mill", Journal of Power Electronics, Vo. 9, No. 5, pp. 700-707.
  2. T. Ono, H. Makino and T. Takinami, 1999, "Development of CWM Producing Method by Dry Type Pulverizer and Application for Low Rank Coal", Coal Preparation, Vol. 21, No. 1, pp. 53-70. https://doi.org/10.1080/07349349908945608
  3. J. H. Seo, S. J. Kim and B. T. Kim, 2014, "Structural Analysis for the Casing of a 800kW Grade Pulverizer Mill Planetary Gear Reducer", Proc. of the KSPSE Autumn Conference. pp. 133-134.
  4. D. B. Park, H. S. Yoo, S. J. Moon and J. H. Lee, 2010, "Effect of the Duct Vane Shape Improvement on the Air Velocity Distribution in a Bowl Type Pulverizer", Proc. of the KSME Autumn Conference, pp. 2562-2567.
  5. G. M. Lee, S. H. Kim, H. J. Kim, I. H. Lee and J. K. Ha, 2001, "An Experimental Study on the Flow Field in a Coal Pulverizer Model with Dynamic Classifier", Proc. of the KSME Autumn Conference, pp. 393-398.
  6. B. K. Arnold, T. Heijkoop, P. G. Lloyd, G. Rubenis and I. R. Sare, 1997, "Wear of cast-bonded components in a coal pulveriser mill", Wear, Vol. 203-205, pp. 663-670.
  7. N. Parida, S. Tarafder, S. K. Das, P. Kumar, G. Das, V. R. Ranganath and D. K. Bhattacharya, 2003, "Failure analysis of coal pulverizer mill shaft", Engineering Failure Analysis, Vol. 10, pp. 733-744. https://doi.org/10.1016/S1350-6307(02)00070-5
  8. S. Y. Song, J. K. Jung, S. D. Choi and H. J. Choi, 2013, "Strength analysis of micro planetary gear reducer using FEA", Proc. of the KSMPE Autumn Conference, p. 110.
  9. ANSYS, 2014, ANSYS User's Manual Version 15.0, ANSYS Inc.

피인용 문헌

  1. High-Temperature Corrosion Characterization for Super-Heater Tube under Coal and Biomass Co-firing Conditions vol.22, pp.1, 2018, https://doi.org/10.9726/kspse.2018.22.1.079