DOI QR코드

DOI QR Code

Development of strut-and-tie model and design guidelines for improved joint in decked bulb-tee bridge

  • Li, Lungui (School of Civil Engineering, Southwest Jiaotong University) ;
  • He, Zhiqi (School of Civil Engineering, Southeast University) ;
  • Ma, Zhongguo John (Department of Civil and Environmental Engineering, University of Tennessee Knoxville) ;
  • Yao, Lingkan (School of Civil Engineering, Southwest Jiaotong University)
  • 투고 : 2012.10.12
  • 심사 : 2013.10.02
  • 발행 : 2013.10.25

초록

This paper focuses on a development of strut-and-tie model (STM) to predict the capacity of an improved longitudinal joint for decked bulb-tee bridge systems. Nine reinforced concrete beam/slab specimens anchored by spliced headed bars with different details were tested. Test results were evaluated and compared with an anticipation of the validated STM. The proposed STM provides a lower bound of the ultimate capacity of the joint zone. It shows that the lap length of headed bars has a significant effect on structural behaviors of the improved joint. To develop a full strength joint, the range of the lap length can be determined by the strength and compatibility requirement. Design recommendations to spliced headed bars, concrete strength, as well as lacer bars in the joint zone are proposed for developing a full strength joint.

키워드

참고문헌

  1. AASHTO LRFD (2010), Bridge Design Specifications, 5th Edition, American Association for State Highway and Transportation Officials, Washington, D.C.
  2. ACI Committee 318 (2011), Building Code Requirements for Structural Concrete (ACI 318-11) and Commentary, American Concrete Institute, Fannington Hills, MI.
  3. Bentz, E.C. and Collins, M.P. (2000), Response-2000 Reinforced Concrete Sectional Analysis. A software downloaded http://www.ecf.utoronto.ca/-bentzlr2k.htm.
  4. Chapman, C.E. (2010), "Behavior of precast bridge deck joints with small bend diameter U-bars", Master Theses at University of Tennessee Knoxville.
  5. Collins, M.P.. and Mitchell, D. (1991), Prestressed Concrete Structures, Prentice Hall, 10 Englewood Cliffs, NJ.
  6. Einea, A., Yehia, S. and Tadros, M.K. (1999), "Lap splices in confined concrete", ACI Structural Journal, 96(6),947-956.
  7. He, Z., Ma, Z., Chapman, C.E. and Liu, Z. (2012), "Longitudinal joints with accelerated construction features in decked bulb-tee girder bridges: strut-and-tie model and design guidelines", ASCE Journal of Bridge Engineering, 18(5),372-379.
  8. Lewis, S. (2009), "Experimental investigation of precast bridge deck joints with U-bar and headed bar joint details", Master theses at University of Tennessee Knoxville.
  9. Li, L., Ma, Z., Griffey, M.E. and Oesterle, R.G. (2010), "Improved longitudinal joint details in decked bulb tees for accelerated bridge construction: concept development", ASCE Journal of Bridge Engineering, 15(3), 327-336. https://doi.org/10.1061/(ASCE)BE.1943-5592.0000067
  10. Li, L., Ma, Z. and Oesterle, R.G. (2010), "Improved longitudinal joint details in decked bulb tees for accelerated bridge construction: fatigue evaluation", ASCE Journal of Bridge Engineering, 15(5), 511-522. https://doi.org/10.1061/(ASCE)BE.1943-5592.0000097
  11. Ma, Z., Chaudhury, S., Millam, J.L. and Hulsey, L. (2007), "Field test and 3D FE modeling of decked bulb-tee bridges", ASCE Journal of Bridge Engineering, 12(3), 306-314. https://doi.org/10.1061/(ASCE)1084-0702(2007)12:3(306)
  12. Ma, Z., Lewis, S., Cao, Q., He, Z., Burdette, E.G. and French, C.E.W. (2012), "Transverse joint details with tight bend diameter U-bars for accelerated bridge construction", ASCE Journal of Structural Engineering,138(6), 697-707. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000518
  13. Ma, Z., Cao, Q., Chapman, C., Burdette, E. and French, C. (2012), "Longitudinal joint details with tight bend diameter U-bars", ACI Structura/Journal, 109(6), 815-824.
  14. Marti, P. (1985), "Basic tools for reinforced concrete design", ACI Journal, 82(1), 46-56.
  15. Morsch, E. (1909), Concrete-Steel Construction, Trans. Goodrich, E.P, Mcgraw-Hill, New York
  16. Mueller, P. (1976), Failure Mechanisms for Reinforced Concrete Beams in Torsion and Bending, lAB SE, V 36-II.
  17. Mueller, P. (1979), "Plastic Analysis of Torsion and Shear in Reinforced Concrete", Final Report, IABSE Colloquium on Plasticity in Reinforced Concrete, Copenhagen, May.
  18. Ritter, W. (1899), "Die bauweise hennebique", Schweizerische Bauzeitung, 33(7), 59-61.
  19. Schlaich, J. and Schafer, K. (1991), "Design and detailing of structural concrete using strut-and-tie models", The Structure Engineer, 69(6), 113-125.
  20. Stanton, J. and Mattock, A.H. (1986), "Load distribution and connection design for precast stemmed multibeam bridge superstructures", NCHRP Rep. 287.
  21. Thompson, M.K., Jirsa, J.O. and Breen, J.E. (2006), "Behavior and capacity of headed reinforcement", ACI Struct. J., 103(4), 522-530.
  22. Zhu, P, Ma, Z., Cao, Q. and French, C. (2012), "Fatigue evaluation of transverse U-bar joint details for accelerated bridge construction", ASCE Journal of Bridge Engineering, 17(2), 191-200. https://doi.org/10.1061/(ASCE)BE.1943-5592.0000257

피인용 문헌

  1. New strut-and-tie-models for shear strength prediction and design of RC deep beams vol.14, pp.1, 2014, https://doi.org/10.12989/cac.2014.14.1.019
  2. Accelerated Construction of Short Span Railroad Bridges in Iran vol.24, pp.1, 2019, https://doi.org/10.1061/(ASCE)SC.1943-5576.0000396
  3. Design formulas for channels subject to combined compression, shear and major axis bending vol.22, pp.1, 2013, https://doi.org/10.1007/s42107-020-00301-8