한국안전학회지 (Journal of the Korean Society of Safety)

  • 제28권2호
  • /
  • Pages.26-30
  • /
  • 2013
  • /
  • 1738-3803(pISSN)
  • /
  • 2383-9953(eISSN)
한국안전학회 (The Korean Society of Safety)
권호 표지
DOI QR코드

DOI QR Code

전자기기의 신호전송을 위한 Photo Couplers(P/C) 의 위험 요소 발굴

Risk Factors Related to Photo Couplers(P/C) for Signal Transmission by Electronic Devices

  • 박형기 (전주대학교 소방안전공학과) ;
  • 최충석 (전주대학교 소방안전공학과)
  • Park, Hyung-Ki (Department of Fire Safety Engineering, Jeonju University) ;
  • Choi, Chung-Seog (Department of Fire Safety Engineering, Jeonju University)
  • 투고 : 2012.12.11
  • 심사 : 2013.02.21
  • 발행 : 2013.04.30
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

The purpose of this study is to find risk factors by analyzing the operation principle of a photo coupler (P/C) used to remove the noise of electronic devices and establish a base for the performance improvement of developed products. It was found from the P/C circuit analysis of normal products that they were equipped with an electrolytic condenser of $0.1{\mu}F$ to smooth system signals. Due to the epoxy resin packing the external part of the P/C, this study experienced a limit to visually examine the damage to it. It could be seen from the analysis of electric characteristics of the P/C that the forward voltage ($V_f$) and reverse current ($I_r$) were 1.3 V and 10 uA, respectively. In addition, it is required that the breakdown voltage (VCE) between the collector (C) and emitter (E) be maintained at less than 35 V. The and of the damaged product #1 were comparatively good. However, the measurement of was 100.0 uA. From this, it is thought that a short circuit occurred to the internal circuit. Moreover, from the fact that the of the damaged product #2 was open circuit and the measurement of was 0.0 uA, it is thought that the collector and emitter was separated or insulation resistance was significantly high. Furthermore, from the fact that the of the damaged product #3 was open circuit and the measurement of was 0.0 uA, it is thought that the space between the collector (C) and emitter (E) failed to meet the design standard or that they were separated. Therefore, it is thought that fabricating the P/C by increasing the reverse current 10 mA to 50 mA will prevent its malfunction.

키워드

참고문헌

  1. Yamazaki, "Safety Design Note of Electronic Circuit", The Nikkan Kogyo Shinbum, pp. 30-36, 2008.
  2. SONY Tech. Training Center, "The Application of Electronic Component", pp. 3-3-3-53, 1995.
  3. Osamu, "Design Capabilities to Determine the Quality", The Nikkan Kogyo Shinbum, pp. 113-121, 2009.
  4. Chung-Seog Choi, Hyun-Woo, Kim, Kyung-Sup Lee, Yang- Su Lim, Chun-Ha Lee and Jae-hee Chung, "Electrical Fire Engineering", Honghwa Technology Publishing Co., pp. 189-198, 405-409, 2004.
  5. Chung-Seog Choi, Hyang-Kon Kim, Dong-Ook Kim and Dong-Woo Kim, "The Analysis of Voltage Waveform and Oxidation Growth of Conductor with Series Arc", The Transactions of The Korean Institute of Electrical Engineers, Vol. 55P, No. 3, pp. 146-152, 2006.
  6. Kil-Mok Shong, Chung-Seog Choi, Young-Su Roh and Hee- Ro Kwak, "Carbonization Characteristics of Phenolic Resin Deteriorated by Tracking," The Transactions of The Korean Institute of Electrical Engineers, 53C-1-1, pp. 1-7, 2004.
  7. Sasaki Hara, "Basic of Reliability Technique" Shuwa System, pp. 32-33, 2009.
  8. H. J. Kim, H. J. Kim, "Innovation Production Management", Hyungseul Publishing Co., pp. 312-316, 2011.
  9. M. Modarres, "Reliability and Risk Analysis", Marcel Dekker Inc, pp. 136-140, 1993.
  10. Kiyoshi Nikawa, "All of LSI Failure Analysis Technique" Kogyo Chosaka, Publishing Co. Ltd, pp. 65-66, 2007,
  11. Technical Committee on Reliability, "Failure Analysis and Countermeasure for Electronic Engineer", pp. 58-59, 2006.
  12. SHARP, "Semiconductor Reliability Handbook Opto-Electronic Devices Edition", IV.22, IV-25, 1993.
  13. Danaka, "Reliability Engineering Guide", Japanese Standard Association, pp. 59-63, 2010.
  14. Aziki, "Reliability Technique of Semiconductor Device", The Institute of Japanese Union of Scientist & Engineering, pp. 95-120, 2008.
  15. Hatsuta et al, "Material Dynamics & Fatigue Design Guide", The Nikkan Kogyo Shinbum, pp. 155-164, 2009.
  16. Hirayama, "Non Destructive Testing Manual", Japanese Standard Association, pp. 24-33, 1995.
  17. Yoshita, "Failure Cause & Countermeasure of Electronic Component", The Nikkan Kogyo Shinbum, pp.43-64, 2006.
  18. Transistor Technic Edit Part, "The Handbook of Electronic Circuit Component", p. 278, 2007.