한국안전학회지 (Journal of the Korean Society of Safety)

  • 제28권2호
  • /
  • Pages.14-20
  • /
  • 2013
  • /
  • 1738-3803(pISSN)
  • /
  • 2383-9953(eISSN)
한국안전학회 (The Korean Society of Safety)
권호 표지
DOI QR코드

DOI QR Code

바닥재 마모에 따른 미끄럼 저항 변화

The Variation of the Slip Resistance with Wear of Floor

  • 김정수 (한국산업안전보건공단 산업안전보건연구원)
  • Kim, Jung-Soo (Occupational Safety and Health Research Institute, KOSHA)
  • 투고 : 2013.01.17
  • 심사 : 2013.02.19
  • 발행 : 2013.04.30
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

All most of floors can become less slip resistant with wear. The deterioration of slip resistance can often occur rapidly. So relatively new products can become hazardous within a short period of time. The main objective of this study was the comparison of slip resistance variations caused by traffic wear and accelerative wear. The second objective was to ascertain the effect of wear, and to find out the causes of slip resistance change. Although statistical differences were observed between results of traffic wear and accelerative wear, the trend of the variations of slip resistance caused by traffic wear and accelerative wear was very similar. The measured slip resistance of tested floor changed up to 29%(and 26.5%) after 100,000 steps(and 750 cycles). As the traffic wear and accelerative wear were progressed, the surface roughness of the tested floor became smoother, and so the floor became more slippery under the wet condition. The abraded(worn out) floor surface tended to become hydrophilic surface, while the new floor surface tended to show hydrophobic nature. This phenomenon would change the wettability of floor surface, and the wettability would affect the variation of slip resistance.

키워드

참고문헌

  1. HSL, "An Examination of Novel Roughness Parameters to be used in Conjunction with the HSE Slips Assessment Tool (SAT)", Health and Safety Laboratory Research Report RR549, 2007.
  2. HSE, "Assessing the Slip Resistance of Flooring", HSE Technical Information Sheet, 2007.
  3. W.R. Chang, M. Hirvonen and R. Gronqvist, "The Effect of Cut-off Length on Surface Roughness Parameters and Their Correlation with Transition Friction", Safety Science, Vol. 42, pp. 755-769, 2004. https://doi.org/10.1016/j.ssci.2004.01.002
  4. I.J. Kim and R. Smith, "Observation of the floor Surface Topography Changes in Pedestrian Slip Resistance Measurements", International Journal of Industrial Ergonomics, Vol. 26, pp. 581-601, 2000. https://doi.org/10.1016/S0169-8141(00)00024-X
  5. W.R. Chang, "Preferred Surface Microscopic Geometric Features on Floors as Potential Interventions for Slip and Fall Accidents on Liquid Contaminated Surfaces", Journal of Safety Research , Vol. 35, pp. 71-79, 2004. https://doi.org/10.1016/j.jsr.2003.09.017
  6. K.W. Li, R. Yu and W. Zhang, "Roughness and Slipperiness of Floor Surface: Tactile Sensation and Perception", Safety Science, Vol. 49, 508-512, 2011. https://doi.org/10.1016/j.ssci.2010.11.010
  7. Y.H. Shin and S.K. Choi, "A Study on the Change of Slipperiness of Building Floor-coverings by Friction Wear", Journal of the Korea Institute of Building Construction, Vol. 5, No. 1, 53-61, 2005. https://doi.org/10.5345/JKIC.2005.5.1.053
  8. C.J. Strautins, "Enhanced Test Method for Assessing Sustainable Slip Resistance", International Conference on Slips, Trips and Falls 2007, pp. 1-5, 2007.
  9. P.A. Schulte, R. Rinehart, A. Okun, C.L.Geraci and D.S. Heidel, "National Prevention through design(PtD) initiative", Journal of Safety Research, Vol. 39, pp. 115-121, 2008. https://doi.org/10.1016/j.jsr.2008.02.021
  10. F.A. Manuele, "Prevention Through Design(PtD): History and Future", Journal of Safety Research, Vol. 39, pp. 127-130, 2008. https://doi.org/10.1016/j.jsr.2008.02.019
  11. W. Creaser, "Prevention through Design(PtD) Safe Design from an Australian Perspective", Journal of Safety Research, Vol. 39, pp. 131-134, 2008. https://doi.org/10.1016/j.jsr.2008.02.018
  12. C.J Strautins, "Sustainable Slip Resistance:An Opportunity for Innovation", http://ebookbrowse.com/sustainable-slip-resistance- an-opportunity-for-innovation-pdf-d73422917.
  13. G. Silva, A. Munoz, C. Feliu, M. Monzo, J. Barbera and C. Soler, "Proposal of a Standard Method for Determining the Durability of Flooring Exposed to Pedestrian Traffic", Vol. 3, pp P.BC 217-236, 2006.
  14. 工藤瑠美, "磨耗による床のすべり抵抗の変化の卽時推定- 方法に関する硏究,"東北工業大學大學院 工學硏究科 建 築學專攻 學位論文, 2007.
  15. J. Sebald, "System Oriented Concept for Testing and Assessment of the Slip Resistance of Safety, Protective and Occupational Footwear", Pro Business GmbH, Berlin, 2009.
  16. Jung Soo Kim, "Evaluation of Dynamic Characteristics of Slipmeters with Force Platform", Journal of the Korean Society of Safety, Vol. 27, No. 5, pp. 1-8, 2012.
  17. Sandia National Laboratories, "Wetting Dynamics on Structured Surfaces", www.sandia.gov/mission/ste/.../Brooks-09. pdf, 2009.
  18. G. Tari, K. Brassington, A. Tenaglia, S. Thorpe and M. Engels, "Classification of Hard Floor Coverings According to their Contribution to Reduce the Risk of Pedestrian Slipping", SlipSTD PAS, ver. 6, 2009.
  19. Rick Houlihan, "Novel Slip Characteristics of Conglomerate Tiles", Research Report RR653, HSE, 2008.
  20. W.R. Chang et al., "The Role of Friction in the Measurement of Slipperiness, Par 1: Friction Mechanisms and Definition of Test Conditions", In: W.R. Chang, T.K. Courtney, R. Granqvist, M. Redfern, editors. Measuring Slipperiness-Human Locomotion and SurfaceFactors: Taylor & Francis; pp. 119-134, 2002.
  21. B.N.J. Persson and M. Scaraggi, "On the Transition from Boun dary Lubrication to Hydrodynamic Lubrication in Soft-Contacts", Journal of Physics: Condensed Matter, Vol. 21, pp. 1-22, 2009.
  22. Y.J. Sheng and S. Jiang, "Effect of Geometrical Characteristics of Surface Roughness on Droplet Wetting", The Journal of Chemical Physics, Vol. 127, pp. 234704-1-7, 2007. https://doi.org/10.1063/1.2804425