초록
근관치료 후 적절한 치관부 밀폐를 위해 레진을 이용한 코어수복방법이 현재 많이 사용되고 있다. 하지만, 근관치료 과정에서 사용되는 NaOCl이나 EDTA같은 근관세척제는 레진 접착에 영향을 주는 것으로 알려져 있으며, 이에 관한 많은 연구들이 이루어져 왔다. 본 연구에서는 ethanol wet bonding을 치수강 상아질에 적용 시에 NaOCl과 EDTA가 결합강도에 미치는 영향에 대해 조사하였다. 30개의 인간 대구치로부터 총 60개의 시편을 얻었고, 이를 무작위로 4개의 군으로 분류했다. G1: 증류수로 세척후 증류수로 마무리 세척, G2: NaOCl로 세척 후 NaOCl로 마무리세척, G3: NaOCl로 세척 후 EDTA로 마무리세척, G4: NaOCl로 세척 후 EDTA로 마무리세척하고 접착과정에서 산부식과정 생략. 접착과정은 인산부식 후 에탄올의 농도를 50%, 70%, 80%, 95% 그리고 100%로 순차적으로 증가시켜가면서 상아질을 탈수시키고 에탄올에 적셔지도록 하였다. 프라이머는 HEMA가 포함되지 않은 상용화된 접착제인 ALL-BOND 3 RESIN과 에탄올을 반반씩 섞어 만들었다. 프라이머 적용 후 ALL-BOND 3 RESIN을 접착제로 사용하였다. 저점도 복합레진을 이용하여 6mm 두께로 적층충전한 후 빔 형태로 잘라 미세인장결합강도 실험을 하였다. NaOCl 처리한 그룹은 미세인장결합강도에 통계적으로 유의한 차이를 보여주지는 않았지만 낮은 평균값을 보여주었다(p=0.052). NaOCl 처리 후 1분간 EDTA로 처리한 그룹은 다른 그룹보다 유의하게 높은 결합강도를 보여주었다(p<0.05). EDTA 처리가 결합강도를 향상 시켰지만, 산부식 과정을 생략할 경우 유의하게 낮은 결합 강도를 보여주었으며, 이는 EDTA처리가 산부식 과정을 대신할 수는 없다는 것을 보여준다.
Sodium hypochlorite and ethylene diamine tetra acetic acid are substances usually used during endodontic treatment. Several studies found that the bonding was negated with certain irrigants and some of the used irrigants have demineralizing and chealating effects, so it was advocated to omit the etching step in etch and rinse adhesive systems. The purpose of this in vitro study was to evaluate the influence of NaOCl & EDTA on the bonding strength of ethanol wet bonding. Thirty human molars were selected and mesiodistally sectioned into halves, thus providing sixty specimens. The specimens were randomly assigned to 4 groups(n=15) according to the irrigant regimen used : (1) irrigated with distilled water for 10min (control); (2) irrigated with 5.25% NaOCl(10min), flushed with 5.25% NaOCl(1min) (3) irrigated with 5.25% NaOCl, flushed with 17% EDTA (4) irrigated with 5.25% NaOCl, flushed with 17% EDTA. Each group was acid-etched with 37% phosphoric acid(except group 4) and had their dentin surfaces dehydrated with ethanol solutions : 50%, 70%, 80%, 95%, 3x100%, 30s for each application. After dehydration, a primer( 50% all bond 3 resin + 50% ethanol) was used, followed by the adhesive(ALL-BOND 3 RESIN) application. Resin composite build-ups were then prepared using an incremental technique. Specimens were sectioned into beams and submitted to a tensile load using a Micro Tensile Tester(Bisco Inc.). The data were statistically analyzed using one-way ANOVA and Tukey HSD at p<0.5 level. There was no significant difference on G1(control) and G2(irrigated with NaOCl only ). (p>0.05). G3(flushed with EDTA) showed significantly high tensile bonding strength compared to the G2 (p<0.05). G4( treated with EDTA but no acid-etching) was significantly lower value than G3. (p<0.05) Although there was no significant difference, 5.25% NaOCl seemed to have an adverse effect on the bonding strength of ethanol wet bonding. The flushing with EDTA after NaOCl irrigation prevents the decrease of bonding strength. The use of 17% EDTA as a final flush can enhance the bonding strength but EDTA flushing can't substitute for a acid-etching.