Journal of the Microelectronics and Packaging Society (마이크로전자및패키징학회지)

The Korean Microelectronics and Packaging Society (한국마이크로전자및패키징학회)
권호 표지
DOI QR코드

DOI QR Code

Peel strengths of the Composite Structure of Metal and Metal Oxide Laminate

Metal과 Metal Oxidefh 구성된 복합구조의 Peel Strength

  • Shin, Hyeong-Won (Rare metals R&D Group, Korea institute of Industrial Technology) ;
  • Jung, Taek-Kyun (Rare metals R&D Group, Korea institute of Industrial Technology) ;
  • Lee, Hyo-Soo (Rare metals R&D Group, Korea institute of Industrial Technology) ;
  • Jung, Seung-Boo (Department of Advanced Material Science and Engineering, Sungkyunkwan University)
  • 신형원 (한국생산기술연구원 희소금속연구그룹) ;
  • 정택균 (한국생산기술연구원 희소금속연구그룹) ;
  • 이효수 (한국생산기술연구원 희소금속연구그룹) ;
  • 정승부 (성균관대학교 신소재공학부)
  • Received : 2013.09.09
  • Accepted : 2013.10.10
  • Published : 2013.12.30
Download PDF
⟨ Previous Next ⟩

Abstract

A lot of various researches have been going on to use heat spreader for LED module. Nano porous aluminum anodic oxide (AAO) applied LED, which is produced from anodization, is easy and economically advantageous. Convensional LED module is consist of aluminum/adhesive/copper circuit. The polymer adhesive in this module is used as heat spreader. However the thermal emission of LED component is degraded because of low heat conductivity of polymer and also reliability of LED component is reduced. Therefore, AAO in this work was applied to heat spreader of LED module which has higher heat conductivity compare to polymer. Bonding strength between AAO and copper circuit was improved with Ti/Cu seed layer by copper sputtering process (DBC) before the bonding. And this copper circuit has been fabricated by electro plating method. Peel strength of AAO and copper circuit in this work showed range between 1.18~1.45 kgf/cm with anodizing process which is very suitable for high power LED application.

양극산화(anodization)공정으로 제작된 규칙성 나노구조의 다공성 산화알루미늄(Aluminum Anodic Oxide, AAO)는 공정이 적용된 LED 모듈은 비교적 쉽고 경제적이므로 최근 LED용 방열소재로 응용하기 위하여 다양하게 연구가 진행되고 있다. 일반적으로 LED 모듈은 알루미늄/폴리머/구리 회로층으로 구성되며 절연체 역할을 하는 폴리머는 히트스프레더로 구성되어있다. 그러나 열전도도가 낮은 폴리머로 인하여 LED부품의 열 방출이 원활하지 못하므로 LED의 수명단축 및 오작동에 영향을 미친다. 따라서, 본 연구에서는 폴리머 대신 상대적으로 열전도도가 우수한 AAO를 양극산화 공정으로 제작하여 히트스프레더(heat spread)로 사용하였다. 이때, AAO와 금속인 구리 회로층간의 접착력을 향상시키기 위하여 스퍼터링 DBC(direct bonding copper)법으로 시드층(seed layer)을 형성한 뒤 최종적으로 전해도금공정으로 구리회로층을 형성하였다. 본 연구에서는 양극 산화공정으로 AAO와 금속간의 접착강도를 개선하여 1.18~1.45 kgf/cm와 같은 우수한 peel strength 값을 얻었다.

Keywords

References

  1. H. Konno, K. Utaka, R. Furuichi. A two step anodizing process of aluminum as a means for improving the chemical and physical properties of oxide films. Corrosion science, 38(12), 2247 (1996). https://doi.org/10.1016/S0010-938X(97)83145-9
  2. K.Y. Ng, A.H.W. Ngan. Effects of pore-channel ordering on the mechanical properties of anodic aluminum oxide nano-honeycombs. Scripta Materialia 66, 439 (2012). https://doi.org/10.1016/j.scriptamat.2011.12.010
  3. M. Norek, W.J.Stepniowski, M. Polanski, D. Zasada, Z. Bojar, J. Bystrzycki. Acomparative study on the hydrogen absorption of thin films at room temperature deposited on non-porous glass substrate and nano-porous anodic aluminum oxide(AAO) template. International journal of hydrogen energy, 36, 11777 (2011). https://doi.org/10.1016/j.ijhydene.2011.06.046
  4. L. Fernandez-Romero, J.M. Montero-Moreno, E. Pellicer, F. Peiro, A. Cornet, J.R. Morante, M. Sarret, C. Muller. Assessment of the thermal stability of anodic alumina membranes at high temperatures. Materials chemistry and physics, 111, 542 (2008). https://doi.org/10.1016/j.matchemphys.2008.05.003
  5. B. Mert, B. Yazici, T. Tuken, G. Kardas, M. Erbil. Anodizing and Corrosion Behaviour of Aluminum. Protection of metals and physical chemistry of surfaces, 47(1), 102 (2011). https://doi.org/10.1134/S2070205110051028
  6. A.M.Kliauga, D.Travessa, M.Ferrante. Al2O3/Tiinterlayer/AISI304 diffusionboned joint microstructural characterization of the two interfaces. Materials characterization, 46, 65(2001). https://doi.org/10.1016/S1044-5803(00)00095-4
  7. H. Lu, C.L. Bao, D.H.Shen, X.J. Zhang, Y.D. Cui, Z.D. Lin. Study of the To/Al2O3interface.Journalofmaterialsscience, 30, 339 (1995). https://doi.org/10.1007/BF00354393
  8. H. Liu, C. Huang, J. Wang, X. Teng. Fabrication and mechanical properties of Al2O3/Ti(C0.7N0.3)nanocomposites.Materialsresearchbulletin, 41, 1215 (2006). https://doi.org/10.1016/j.materresbull.2006.01.014
  9. A.G. Limonov. Numeric simulation of the formation of hexagonal nanoscale structure arrays in anodic aluminum oxide. Matematicheskoe modelirovanie, 22(8), 97 (2010).
  10. J.M. Montero-Moreno, M. Sarret, C. Muller. Self-ordered porous alumina by two step anodizing at constant current: Behaviour and evolution of the structure. Microporous and mesoporous materials 136, 68 (2010). https://doi.org/10.1016/j.micromeso.2010.07.022
  11. Minseok Choi, Anderson Janotti, Chris G. Native point defects and dangling bonds in ${\alpha}-Al_2O_3$: Journal of applied physics 113, 044501(2013). https://doi.org/10.1063/1.4784114