Computers and Concrete

  • 제10권2호
  • /
  • Pages.105-119
  • /
  • 2012
  • /
  • 1598-8198(pISSN)
  • /
  • 1598-818X(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Flexural performance and fiber distribution of an extruded DFRCC panel

  • 투고 : 2011.03.10
  • 심사 : 2011.11.09
  • 발행 : 2012.08.25
⟨ 이전 논문 다음 논문 ⟩

초록

This paper presents the mix composition and production method that was applied to an extruded Ductile Fiber Reinforced Cement Composite (DFRCC) panel, as well as the flexural performance, represented by deformation hardening behavior with multiple cracking. The effect of fiber distribution characteristics on the flexural behavior of the panel is also addressed. In order to demonstrate the fiber distribution effect, a series of experiments and analyses, including a sectional image analysis and micromechanical analysis, was performed. From the experimental and analysis results, it was found that the flexural behavior of the panel was highly affected by a slight variation in the mix composition. In terms of the average fiber orientation, the fiber distribution was found to be similar to that derived under the assumption of a two-dimensional random distribution, irrespective of the mix composition. In contrast, the probability density function for the fiber orientation was measured to vary depending on the mix composition.

키워드

참고문헌

  1. Akkaya, Y., Peled, A. and Shah, S.P. (2000), "Parameters related to fiber length and processing in cementitious composites", Mater. Struct., 33(8), 525-524. https://doi.org/10.1007/BF02480530
  2. Fu, S.Y. and Lauke, B. (1996), "Effects of fiber length and fiber orientation distributions on the tensile strength of short-fiber-reinforced polymers", Compos. Sci. Technol., 56(10), 1179-1190. https://doi.org/10.1016/S0266-3538(96)00072-3
  3. Kanda, T. and Li, V.C. (2006), "Practical design criteria for saturated pseudo strain hardening behavior in ECC", J. Adv. Concrete Technol., 4(1), 59-72. https://doi.org/10.3151/jact.4.59
  4. Kim, J.K., Kim, J.S., Ha, G.J. and Kim, Y.Y. (2007), "tensile and fiber dispersion performance of ECC produced with ground granulated blast furnace slag", Cement Concrete Res., 37(7), 1096-1105. https://doi.org/10.1016/j.cemconres.2007.04.006
  5. Lee, B.Y. (2009), "Fiber distribution evaluation using digital image processing and its effect on tensile behavior of fiber reinforced cement composites", PhD Thesis, KAIST.
  6. Lee, B.Y., Kim, J.K., Kim, J.S. and Kim, Y.Y. (2009), "Quantitative evaluation technique of pva (polyvinyl alcohol) fiber dispersion in engineered cementitious composites", Cement Concrete Comp., 31(6), 408-417. https://doi.org/10.1016/j.cemconcomp.2009.04.002
  7. Lee, B.Y., Kim, J.K. and Kim, Y.Y. (2010a), "Prediction of ECC tensile stress-strain curves based on modified fiber bridging relations considering fiber distribution characteristics", Comput. Concrete, 7(5), 455-468. https://doi.org/10.12989/cac.2010.7.5.455
  8. Lee, B.Y., Lee, Y., Kim, J.K. and Kim, Y.Y. (2010b), "Micromechanics-based fiber-bridging analysis of strainhardening cementitious composite accounting for fiber distribution", CMES-Comp. Model. Eng., 61(2), 111-132.
  9. Leung, C.K.Y. (1996), "Design criteria for pseudoductile fiber-reinforced composites", J. Eng. Mech.-ASCE, 122(1), 10-14. https://doi.org/10.1061/(ASCE)0733-9399(1996)122:1(10)
  10. Li, V.C. and Leung, K.Y. (1992), "Steady-state and multiple cracking of short random fiber composites", J. Eng. Mech.-ASCE, 118(11), 2246-2264. https://doi.org/10.1061/(ASCE)0733-9399(1992)118:11(2246)
  11. Li, V.C., Wu, C., Wang, S., Ogawa, A. and Saito, T. (2002), "Interface tailoring for strain-hardening PVA-ECC", ACI Mater. J., 99(5), 463-472.
  12. Marshall, D.B. and Cox, B.N. (1988), "A J-integral method for calculating steady-state matrix cracking stressed in composites", Mech. Mater., 7(2), 127-133. https://doi.org/10.1016/0167-6636(88)90011-7
  13. Roth, M.J., Slawson, T.R. and Flores, O.G. (2010), "Flexural and tensile properties of a glass fiber-reinforced ultra-high-strength concrete: an experimental, micromechanical and numerical study", Comput. Concrete, 7(2), 169-190. https://doi.org/10.12989/cac.2010.7.2.169
  14. Shao, Y. and Shah, S.P. (1997), "Mechanical properties of PVA fiber reinforced cement composites fabricated by extrusion processing", ACI Mater. J., 94(6), 555-564.
  15. Shao, Y., Markunte, S. and Shah, S.P. (1995), "Extruded fiber-reinforced composites", Concrete Int., 17(4), 48-53.
  16. Stang, H. and Li, V.C. (1999), "Extrusion of ECC-Material", Proceedings of High Performance Fiber Reinforced Cement Composites 3 (Reinhardt and Naaman, A. (eds)), Chapman & Hull, 203-212.
  17. Takashima, H., Miyagai, K., Hashida, T. and Li, V.C. (2003), "A design approach for the mechanical properties of polypropylene discontinuous fiber reinforced cementitious composites by extrusion molding", Eng. Fract. Mech., 70(7), 853-870. https://doi.org/10.1016/S0013-7944(02)00154-6
  18. Torigoe, S., Horikoshi, T. and Ogawa, A. (2003), "Study on evaluation method for PVA fiber distribution in engineered cementitious composite", J. Adv. Concrete Technol., 1(3), 265-268. https://doi.org/10.3151/jact.1.265
  19. Vincent, L. (1993), "Morphological grayscale reconstruction in image analysis: applications and efficient algorithms", IEEE T. Image Process., 2(2), 176-201. https://doi.org/10.1109/83.217222
  20. Vincent, L. and Soille, P. (1991), "Watesheds in digital spaces: An efficient algorithm based on immersion simulations",. IEEE T. Pattern Anal., 13(6), 583-598. https://doi.org/10.1109/34.87344
  21. Wang, S. and Li, V.C. (2006), "Polyvinyl alcohol fiber reinforced engineered cementitious composites: material design and performances", Proceedings of Int'l RILEM Workshop on HPFRCC in Structural Applications, RILEM SARL, 65-73.

피인용 문헌

  1. Experiments and failure analysis of SHCC and reinforced concrete composite slabs vol.56, 2015, https://doi.org/10.1016/j.engfailanal.2015.01.009
  2. Cyclic Responses of Steel Reinforced ECC Column under Reversed Cyclic Loading Conditions vol.19, pp.4, 2015, https://doi.org/10.11112/jksmi.2015.19.4.075
  3. PDMS 흡수방지재를 적용한 SHCC의 압축강도 및 염화물이온 침투저항성 vol.22, pp.6, 2018, https://doi.org/10.11112/jksmi.2018.22.6.016
  4. 패류 껍질층의 경계면을 모방한 고연성 시멘트 복합재료의 휨 거동 vol.24, pp.1, 2012, https://doi.org/10.11112/jksmi.2020.24.1.108