Advances in materials Research

Techno-Press (테크노프레스)
권호 표지
DOI QR코드

DOI QR Code

Laser brazing molybdenum using two titanium base fillers

  • Lin, Chia-Chen (Department of Materials Science and Engineering, National Taiwan University) ;
  • Lee, Cheng-Han (Department of Materials Science and Engineering, National Taiwan University) ;
  • Shiue, Ren-Kae (Department of Materials Science and Engineering, National Taiwan University) ;
  • Shy, Hsiou-Jeng (Chung-Shan Institute of Science and Technology, Materials & Electro-Optics Research Division)
  • Received : 2012.04.01
  • Accepted : 2012.07.16
  • Published : 2012.09.25
⟨ Previous Next ⟩

Abstract

Brazing Mo using Ti and Ti-15-3 foils has been investigated in the experiment. For traditional furnace brazing, solidification shrinkage voids cannot be completely removed from the joint even the brazing temperature increased to 2013 K and 160 ${\mu}m$ thick Ti foil applied in brazing. Similar results are observed from the joint using Ti-15-3 filler. In contrast, the quality of laser brazed joint is much better than that of furnace brazed joint. A sound joint is achieved after laser brazing. Tensile strengths of 418 and 373 MPa are obtained from laser brazed joints at the power of 800W and travel speed of 5 mm/s using Ti and Ti-15-3 fillers, respectively. All laser brazed joints are fractured at the brazed zone and cleavage dominated fractures are widely observed from their fractographs. The Ti base fillers show potential in laser brazing Mo substrate.

Keywords

Acknowledgement

Supported by : Chung-Shan Institute of Science and Technolog

References

  1. Bao, J.X. (2007), "Preparation and performance analysis of barium dispenser cathodes", Vacuum, 81(9), 1029-1034. https://doi.org/10.1016/j.vacuum.2006.12.014
  2. Davis, J.R. (1990), ASM handbook vol. 2 properties and selection: nonferrous alloys and special-purpose materials, ASM International, Materials Park, USA.
  3. Hiraoka, Y. and Nishikawa, S. (1996), "Joining of single-crystalline molybdenum and carbon-ceramics by using palladium and palladium-silver alloy as brazing metal", Int. J. Refract. Met. H., 14(5-6), 311-317. https://doi.org/10.1016/S0263-4368(96)00017-0
  4. Hiraoka, Y. (1992), "Brazing of single-crystalline molybdenum by using Pd-20% Ag alloy", Int. J. Refract. Met. H., 11(5), 303-307. https://doi.org/10.1016/0263-4368(92)90042-Z
  5. Humpston, G and Jacobson, D.M. (1993), Principles of soldering and brazing, ASM International, Materials Park, USA.
  6. Lin, C.C., Chen, C., Shiue, R.K. and Shi, S.C. (2011), "Vacuum brazing Mo using Ti-Ni-Nb braze alloys", Int. J. Refract. Met. H., 29(5), 641-644. https://doi.org/10.1016/j.ijrmhm.2011.04.003
  7. Lin, C.C., Shu, C.H., Chen, C., Shiue, R.K. and Shy, H.J. (2012), "Brazing porous tungsten and molybdenum using palladium and titanium foils", Int. J. Refract. Met. H., 31(3), 284-287. https://doi.org/10.1016/j.ijrmhm.2011.10.007
  8. Liu, G.W., Valenza, F. and Muolo M.L. (2010), "SiC/SiC and SiC/Kovar joining by Ni-Si and Mo interlayers", J. Mater. Sci., 45(16), 4299. https://doi.org/10.1007/s10853-010-4337-3
  9. Massalski, T.B. (1990), Binary alloy phase diagrams, ASM International, Materials Park, USA.
  10. Olson, D.L. (1990), Metals handbook, Vol. 6 Welding brazing and soldering, ASM International, Materials Park, USA.
  11. Schwartz, M. (1995), Brazing: for the engineering technologist, ASM International, Materials Park, USA.
  12. Singh, M. and Asthana, R. (2009), "Joining of ZrB(2)-based ultra-high-temperature ceramic composites to Cuclad- molybdenum for advanced aerospace applications", Int. J. Appl Ceram. Tec., 6(2), 113-133. https://doi.org/10.1111/j.1744-7402.2008.02291.x
  13. Smith, W.F. (1993), Structure and properties of engineering alloys, McGraw-Hill Inc., New York.
  14. Vancil, B.K. and Wintucky, E.G. (2005), "Weld techniques for reservoir cathodes", Appl. Surf. Sci., 251(1-4), 101-105. https://doi.org/10.1016/j.apsusc.2005.03.150
  15. Zhang, L., Qin, M. and Qu, X. (2009), "Study on active brazing of AlN ceramics and Mo-Cu alloy", 38(2), 2159-2162.