Structural Engineering and Mechanics

  • 제42권3호
  • /
  • Pages.409-424
  • /
  • 2012
  • /
  • 1225-4568(pISSN)
  • /
  • 1598-6217(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Free vibration analysis of tapered FRP transmission poles with flexible joint by finite element method

  • Saboori, Behnam (Centre of Excellence for Research in Advanced Materials & Structures, Faculty of Mechanical Engineering, K.N. Toosi University of Technology) ;
  • Khalili, Seyed Mohammad Reza (Centre of Excellence for Research in Advanced Materials & Structures, Faculty of Mechanical Engineering, K.N. Toosi University of Technology)
  • 투고 : 2011.10.13
  • 심사 : 2012.04.03
  • 발행 : 2012.05.10
⟨ 이전 논문 다음 논문 ⟩

초록

Since relatively low elasticity modulus of the FRP materials results in lower natural frequencies, it is necessary to study the free vibration of FRP transmission poles. In this paper, the free vibration of tapered FRP transmission poles with thin-walled circular cross-section is investigated by a tapered beam element. To model the flexible joints of the modular poles, a rotational spring model is used. Modal analysis is performed for typical FRP poles with/without joint and they are also modeled by ANSYS commercial finite element software. There is a good correlation between the results of the tapered beam finite element model and those obtained from ANSYS as well as the existing experimental results. The effects of different geometries, material lay-ups, concentrated masses at the pole tip, and joint flexibilities are evaluated. Moreover, it is concluded that using tougher fibres at the inner and outer layers of the cross-section, results in higher natural frequencies, significantly.

키워드

참고문헌

  1. ANSYS, Inc. (2007), ANSYS User's Manual for Rev. 11.0, ANSYS, USA.
  2. Caracoglia, L. and Jones, N.P. (2007), "Numerical and experimental study of vibration mitigation for highway light poles", Eng. Struct., 29, 821-831. https://doi.org/10.1016/j.engstruct.2006.06.023
  3. Caracoglia, L. and Velazquez, A. (2008), "Experimental comparison of the dynamic performance for steel, aluminum and glass-fiber-reinforced-polymer light poles", Eng. Struct., 30, 1113-1123. https://doi.org/10.1016/j.engstruct.2007.07.024
  4. Gould, P.L. and Basu, P.K. (1977), "Geometric stiffness matrices for the finite element analysis of rotational shells", J. Struct. Mech., 5, 87-105. https://doi.org/10.1080/03601217708907307
  5. Ibrahim, S. and Polyzois, D. (1999), "Ovalization analysis of fibre-reinforced poles", Compos. Struct., 45, 7-12. https://doi.org/10.1016/S0263-8223(98)00137-8
  6. Jones, R.M. (1998), Mechanics of Composite Materials, Scripta Book Co., Washington DC.
  7. Kim, N.I., Shin, D.K. and Park, Y.S. (2010), "Coupled stability analysis of thin-walled composite beams with closed cross-section", Thin Wall. Struct., 48, 581-596. https://doi.org/10.1016/j.tws.2010.03.006
  8. Lin, Z.M. (1995), "Analysis of pole-type structures of fibre-reinforced plastics by finite element method", Ph.D. Thesis, University of Manitoba, Canada.
  9. Mabie, H.H. and Rogers, C.B. (1972), "Transverse vibrations of double-tapered cantilever beams", J. Acoust. Soc. Am., 51, 1771-1774. https://doi.org/10.1121/1.1913028
  10. Mabie, H.H. and Rogers, C.B. (1974), "Transverse vibrations of double-tapered cantilever beams with end support and with end mass", J. Acoust. Soc. Am., 55, 986-989. https://doi.org/10.1121/1.1914673
  11. Metiche, S. and Masmoudi, R. (2007), "Full-scale flexural testing on fiber-reinforced polymer (FRP) poles", Open Civ. Eng. J., 1, 37-50. https://doi.org/10.2174/1874149500701010037
  12. Mohamed, H. and Masmoudi, R. (2009), "Design optimization of GFRP pole structures using finite element analysis", Proceeding of the ACMA 2009 Conference, Tampa, Florida, USA.
  13. Navaratna, D.R., Pian, T.H.H. and Wittmer, E.A. (1968), "Stability analysis of shell of revolution by the finite element method", AIAA J., 6, 355-360. https://doi.org/10.2514/3.4502
  14. Noor, A.K., Burton, W.S. and Peters, J.M. (1991), "Assessment of computational models for multilayered composite cylinders", Int. J. Solids Struct., 27, 1269-1286. https://doi.org/10.1016/0020-7683(91)90162-9
  15. Polyzois, D., Raftoyiannis, I.G. and Ibrahim, S. (1998), "Finite elements method for the dynamic analysis of tapered composite poles", Compos. Struct., 43, 25-34. https://doi.org/10.1016/S0263-8223(98)00088-9
  16. Raftoyiannis, I.G. and Polyzois, D. (2007), "The effect of semi-rigid connections on the dynamic behavior of tapered composite GFRP poles", Compos. Struct., 81(1), 70-79. https://doi.org/10.1016/j.compstruct.2006.07.015
  17. Rao, S.S. (1995), Mechanical Vibrations, Addison Wesley, MA.
  18. Springer, G.S. and Kollar, L.P. (2003), Mechanics of Composite Structures, Cambridge University Press, New York.
  19. Thomsen, J.J. (2003), Vibrations and Stability, Springer Press, Berlin.
  20. Yuan, R.L., Hasen, Z., Green, A. and Bisarnsin, T. (1991), "Fibre-reinforced plastic composite columns", Proceedings of Specialty Conference on Advanced Composite Material in Civil Engineering Structures, ASCE, 205-211.
  21. Zabihollah, A. and Ganesan, R. (2010), "Buckling analysis of tapered composite beams using a higher order finite element formulation", J. Reinf. Plast. Comp., 29, 2663-2683. https://doi.org/10.1177/0731684409352124

피인용 문헌

  1. Nonlinear finite element analysis of loading transferred from column to socket base vol.11, pp.5, 2013, https://doi.org/10.12989/cac.2013.11.5.475
  2. Nonlinear vibration analysis of a type of tapered cantilever beams by using an analytical approximate method vol.59, pp.1, 2016, https://doi.org/10.12989/sem.2016.59.1.001