DOI QR코드

DOI QR Code

Properties of Hand-made Clay Balls used as a Novel Filter Media

  • Rajapakse, J.P. (Science and Engineering Faculty, Queensland University of Technology) ;
  • Madabhushi, G. (Department of Engineering, Cambridge University) ;
  • Fenner, R. (Department of Engineering, Cambridge University) ;
  • Gallage, C. (Science and Engineering Faculty, Queensland University of Technology)
  • 투고 : 2012.05.23
  • 심사 : 2012.11.27
  • 발행 : 2012.12.25

초록

Filtration using granular media such as quarried sand, anthracite and granular activated carbon is a well-known technique used in both water and wastewater treatment. A relatively new pre-filtration method called pebble matrix filtration (PMF) technology has been proved effective in treating high turbidity water during heavy rain periods that occur in many parts of the world. Sand and pebbles are the principal filter media used in PMF laboratory and pilot field trials conducted in the UK, Papua New Guinea and Serbia. However during first full-scale trials at a water treatment plant in Sri Lanka in 2008, problems were encountered in sourcing the required uniform size and shape of pebbles due to cost, scarcity and Government regulations on pebble dredging. As an alternative to pebbles, hand-made clay pebbles (balls) were fired in a kiln and their performance evaluated for the sustainability of the PMF system. These clay balls within a filter bed are subjected to stresses due to self-weight and overburden, therefore, it is important that clay balls should be able to withstand these stresses in water saturated conditions. In this paper, experimentally determined physical properties including compression failure load (Uniaxial Compressive Strength) and tensile strength at failure (theoretical) of hand-made clay balls are described. Hand-made clay balls fired between the kiln temperatures of $875^{\circ}C$ to $960^{\circ}C$ gave failure loads of between 3.0 kN and 7.1 kN. In another test when clay balls were fired to $1250^{\circ}C$ the failure load was 35.0 kN compared to natural Scottish cobbles with an average failure load of 29.5 kN. The uniaxial compressive strength of clay balls obtained by experiment has been presented in terms of the tensile yield stress of clay balls. Based on the effective stress principle in soil mechanics, a method for the estimation of maximum theoretical load on clay balls used as filter media is proposed and compared with experimental failure loads.

키워드

참고문헌

  1. AIT (2003), Small and medium scale industries in Asia: Energy and Environment - Brick and Ceramic Sectors, Asian Regional Research Programme in Energy, Environment and Climate Phase III (ARRPEEC-III), Regional Energy Resources Information Center (RERIC), Asian Institute of Technology, Bangkok, Thailand, 2003.
  2. Ali, Z.A. (2005), "Properties of Malaysian fired clay bricks and their evaluation with international masonry specifications", A case study, Mater of Engineering Thesis, Universiti Teknologi Malaysia.
  3. Andam, A.A. (1990), "Optimum firing temperature for some clay bricks", Seminar on Local Materials for Housing, Third International Seminar of the African Network of Scientific and Technological Institutions (ANSTI a UNESCO-sponsored network), University of Mauritius, March 1990.
  4. AS 1225-1984, Standards Association of Australia (1984), "Clay Building Bricks."
  5. ASTM C 62-89a, American Society for Testing Materials (1990), "Standard Specification for Building Brick" (Solid Masonry Units Made from Clay or Shale). United States of America.
  6. Bakhteri, J., Makhtar, A.M. and Sambasivam, S. (2004), Finite element modeling of structural clay brick masonry subjected to axial compression, Journal Teknologi, 41(B), Dis. 2004: 57-78, University Teknologi Malaysia.
  7. BS 3921: 1985, British Standards Institution (1985), "British Standard Specification for Clay Bricks," London.
  8. Elert, K., Cultrone, G., Navarra, C.R. and Pardo, E.S. (2003), "Durability of bricks used in the conservation of historic buildings - influence of composition and microstructure", Journal of Cultural Heritage, 4, 91-99, DOI: 10.1016/S1296-2074(03)00020-7.
  9. Frocht, M.M. and Guernsey, F. (1952), "A special investigation to develop a general method for threedimensional photoelastic stress analysis", Contract No. NAw-5959: Natnl. Adv. Comm. For Aeronautics Technical Note 2822.
  10. Hiramatsu, Y. and Oka, Y. (1966), "Determination of the tensile strength of rock by a compression test of an irregular test piece", Int. J. Rock Mech. Min. Sci. 2, 89-99. Pergamon Press Ltd.
  11. Hoek, E. (1977), "Rock mechanics laboratory testing in the context of a consulting engineering organization", Int. J. Rock Mech. Min. Sci. and Geomech, 14, 93-101. https://doi.org/10.1016/0148-9062(77)90201-7
  12. Humby, M.S., Fitzpatrick, C.S.B. and Stevenson, D.G. (1996), "Development of a friability test for granular filter media", J. CIWEM, 10(2), 87-91.
  13. Johari, I., Said, S., Hisham, B., Bakar, A. and Ahmad, Z.A. (2010), "Effect of the firing temperature on microstructure and physical properties of clay bricks from Beruas (Malaysia)", Science of Sintering, 42(2), 245-254. https://doi.org/10.2298/SOS1002245J
  14. Purchas, D.B. and Sutherland, K. (2002), Handbook of Filter Media, 2nd Edition, Elsevier.
  15. Rajapakse, J.P. (2009), "Simple water treatment: Sustainable implications of pebble matrix filtration", Centre for Sustainable Development, CUED, Cambridge University, UK, unpublished.
  16. Rajapakse, J.P. and Fenner, R.A. (2011), "Evaluation of Alternative Media for Pebble Matrix Filtration Using Clay Balls and Recycled Crushed Glass", J. Environ. Eng., 137(6), June 1, pp 517-524. (C)ASCE. https://doi.org/10.1061/(ASCE)EE.1943-7870.0000350
  17. Rajapakse, J.P. and Ives, K.J. (1990), "Prefiltration of very highly turbid waters using pebble matrix filtration", Water Environ. J., 4(2), 140-147. https://doi.org/10.1111/j.1747-6593.1990.tb01569.x
  18. Rajapakse, J.P. and Ives, K.J. (2003), "Field trials of a simple surface water treatment package for rural supply (Part I)", Environ. Eng., 4(1), 16-20.
  19. Rajapakse, J.P., Jovanoviæ, B. and Ljubisavljeviæ, D. (2005), "Field trails of a simple surface water treatment package for rural supply (Part II), Pebble matrix filtration field trials in Serbia and Montenegro", Environ. Eng., 6(3), 17-19.
  20. Rusnak, J. and Mark, C. (2000), "Using the point load test to determine the uniaxial compressive strength of coal measure rock", Proceedings of 19th International Conference on Ground Control in Mining, Morgantown, WV, pp. 362-363.
  21. SS103:1974, Singapore Institute of Standard and Industrial Research (1974), "Specification for Burnt Clay and Shale bricks."
  22. Sternberg, E. and Rosenthal, F. (1952), "The elastic sphere under concentrated loads", J. Appl. Mech. 19(4), 413-421.

피인용 문헌

  1. Estimation of Poisson’s Ratio and Variation of Tensile Yield Strength of Composite Clay Balls Used in Pebble Matrix Filtration vol.29, pp.9, 2017, https://doi.org/10.1061/(ASCE)MT.1943-5533.0001957
  2. Strength properties of composite clay balls containing additives from industry wastes as new filter media in water treatment vol.8, pp.6, 2015, https://doi.org/10.12989/gae.2015.8.6.859
  3. Experimental Investigation of Enzyme Stabilization and Its Effect on Clay Brick vol.145, pp.4, 2019, https://doi.org/10.1061/(ASCE)CO.1943-7862.0001609
  4. Mechanical resistance of granular activated carbon media in drinking water treatment vol.34, pp.suppl1, 2012, https://doi.org/10.1111/wej.12535