Nuclear Engineering and Technology

  • 제43권5호
  • /
  • Pages.469-476
  • /
  • 2011
  • /
  • 1738-5733(pISSN)
  • /
  • 2234-358X(eISSN)
한국원자력학회 (Korean Nuclear Society)
권호 표지
DOI QR코드

DOI QR Code

ABRASIVE BLASTING TECHNOLOGY FOR DECONTAMINATION OF THE INNER SURFACE OF STEAM GENERATOR TUBES

  • 투고 : 2010.12.03
  • 심사 : 2011.04.11
  • 발행 : 2011.10.31
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

The inner surfaces of bundled inconel tubes from steam generators in South Korean nuclear power plants are contaminated with cobalt and abrasive blasting equipment has been developed to efficiently remove the cobalt. The principal parameters related to the efficient removal using this equipment are the type of abrasive, the distance from the nozzle, and the blasting time. Preliminary tests were performed using oxidized inconel samples which enabled the simulation of cobalt removal from the radioactive inconel samples. The oxygen in the oxidized samples and the cobalt in the radioactive inconel were removed more effectively using the blasting distance, blasting time, and a silicon carbide abrasive. Using the developed abrasive blasting equipment, the optimum decontamination conditions for radioactive inconel samples were blasting for more than 6 minutes using silicon carbides under 5 atmospheric pressures.

키워드

참고문헌

  1. I.M. Hutchings, N.H. Macmillan, D. G. Rickerby, "Further studies of the oblique impact of a hard sphere against a ductile solid," Int. J. Mech. Sci., 23 (1981).
  2. M. Dundar, O.T. Inal, J. Stringer, "The effect of particle size on the erosion of a ductile material at the low particle size limit," Wear, 233-235 (1999).
  3. G.P. Tilly, W. Sage. "The interaction of particle and material behavior in erosion processes," Wear, 16 (1970).
  4. M. Buijs, "Erosion of glass as modeled by indentation theory," J. Am. Ceram. Soc., 77 (1994).
  5. P.J. Slikkerveer, P.C.P. Bouten, F.H. int't Veld, H. Scholten, "Erosion and damage by sharp particles," Wear, 217,2 (1998).
  6. P.J. Slikkerveer, "Mechanical etching of glass by power blasting," PhD Thesis, Eindhoven University of Technology, (1999).
  7. E. Bolloy, S Thurre, E. Walckiers, A. Sayah, M.A.M. Gijs, "Powder blasting as a new technology for intertial sensor fabrication," Proc. 13th European conference on soild-state sensor , The Hague, The Netherlands, Sep. 12-15, 1999.
  8. E. Belloy, S. Thrre, E. Walckiers, A. Sayah, M. A. M. Gijs, "The introduction of powder blasting for sensors and microsystem applications," Sens. Actuators, A 84 (2000).
  9. T.S. Baller, G.G. P. van Gorkom, N. Nambert, E.A. Montie P.H.F. Trompenaars, S.T. de Zwart, "Construction and physical processings of Zeus panels," Philips J. Res., 50 (1996).
  10. J. Li, I.M. Hutchings, "Resistance of cast polyurethane elastomers to solid particle erosion," Wear, 135 (1990).
  11. P.J. Slikkerveer, M.H.A. van Dongen, F.J. Touwslager, "Erosion of elastomeric protective coating," Wear, 236 (1999).
  12. P.J. Slikkerveer, P.C.P. Bouten, F.C.M. de Haas, "High quality of brittle materials by powder blasting," Sensors Actuators, 85 (2000).
  13. H. Wensink, H.V. Jansen, J.W. Berenschot , M.C. Elwenspock, "Mask materials for powder blasting," J. Micromech. Microeng., 10 (2000).
  14. H. Wensink, J.W. Berenschot, H. V. Jansen, M.C. Elwenspoek, "High resolution powder blast micromachining," Proc. Int. Conf. Micro Electro mechanical Systems (MEMS-2000), Miyazaki, Japan, Jan 23-27, 2000.
  15. G. Krause, "Concepts for treatment and recycling of Steam Generators and other big components from operation and decommissioning of nuclear facilities", International Nuclear Forum, 6TH - 8TH, Varna, Bulgaria, 2007