참고문헌
- Jang, H. S., 1997, "The Handbook of Advanced Aluminum Technology, " Hanlimwon, pp. 921-933.
- Myhr, O. R., Grong, O. and Andersen, S. J., 2001, "Modelling of the Age Hardening Behavior of Al-Mg-Si Alloys," Acta Materialia, Vol. 49, pp. 65-75. https://doi.org/10.1016/S1359-6454(00)00301-3
- Park, S. H., Koo, S. H., Lee, B. U. and Eun, I. S., 1997, "Analysis and Measurement of Residual Stress of Al7075 Ring Rolls after Quenching and Stress Relieving," Journal of the Korean Society Propulsion Engineers, Vol. 1, No. 1, pp.104-110.
- Dolan, G. P. and Robinson, J. S., 2004, "Residual Stress Reduction in 7175-T73, 6061-T6 and 2017A-T4 Aluminum Alloys Using Quenching Factor Analysis," Jour. Mater. Pro. Tech., Vol. 153, pp. 346-351. https://doi.org/10.1016/j.jmatprotec.2004.04.065
- Kim, H. S. and Lee, D. N., 1978, "Relief of Residual Quenching Stresses in 2024 Aluminum Alloy, " Kor. J. Met. Mater., Vol. 16, No. 4, pp. 233-242.
- Ian, M., 2004, "Residual Stress Reduction During Quenching of Wrought 7075 Aluminum Alloy," Master's Thesis.
- Lados, D. A., Apelian, D. and Wang, L., 2010, "Minization of Residual Stress in Heat-Treatment Al-Si-Mg Cast Alloys Using Uphill Quenching: Mechanical and Effects on Static and Dynamic Properties," Mater. Sci. Eng. A, Vol. 527, pp. 3159-3165. https://doi.org/10.1016/j.msea.2010.01.064
- Hill, H. N., Barker, R. S. and Willey, L. A., 1960, ASM, Vol. 52, pp.657-674.
- Ko, D. H., Kim, T. J., Lim, H. J., Lee, J. M. and Kim, B. M., 2011, "FE-simulation and Measurement of Residual Stress for Al6061-T6 Heat Treatment," Trans. of the KSME (A), Vol. 35, No. 7, pp. 717-722. https://doi.org/10.3795/KSME-A.2011.35.7.717
- Juijerm, P. and Altenberger, I., 2006, "Residual Stress Relaxation of Deep-Rolled Al-Mg-Si-Cu Alloy During Cyclic Loading at Elevated Temperature," Scripta Materialia, Vol. 55, pp. 1111-1114. https://doi.org/10.1016/j.scriptamat.2006.08.047
- Juijerm, P., Altenberger, I. and Scholtes, B., 2007, "Influence of Ageing on Cyclic Deformation Behavior and Residual Stress of Deep Rolled As-Quenched Aluminum Alloy AA6110, " International Journal of Fatigue, Vol. 29, pp. 1374-1382. https://doi.org/10.1016/j.ijfatigue.2006.10.008
- Simsir, C. and Gur, C. H., 2008, "3D FEM Simulation of Steel Quenching and Investigation of the Effect of Asymmetric Geometry on Residual Stress Distribution," Jour. Mater. Pro. Tech., Vol. 207, pp. 211-221. https://doi.org/10.1016/j.jmatprotec.2007.12.074
- Berger, M. C. and Gregory, J. K., 1999, "Residual Stress Relaxation in Shot Peened Timetal 21s," Mater. Sci. Eng. A, Vol. 263, pp. 200-204. https://doi.org/10.1016/S0921-5093(98)01165-4
- Yamamoto, Y., Sasaki, G., Yamakawa, K., Ota, M., 2000, "High-Strength and High Electrical Conductivity Copper Alloy for High-Pin-Count Leadframes," Hitachi Cable Review, No. 19, pp. 65-70.
- Rosen, M., 1989, "Eddy Current Analysis of Precipitation Kinetics in Aluminum Alloys," Metallurgical Transactions A, Vol. 20A, pp. 605-610.
- Salazar-Guapuriche, MA, Zhao, YY., Pitman, A. and Greene, A., 2006, "Correlation of Strength with Hardness and Electrical Conductivity for Aluminum Alloy 7010," Material Science Forum, Vols. 519-521, pp. 853-858. https://doi.org/10.4028/www.scientific.net/MSF.519-521.853