Composites Research

  • 제24권2호
  • /
  • Pages.30-37
  • /
  • 2011
  • /
  • 2288-2103(pISSN)
  • /
  • 2288-2111(eISSN)
한국복합재료학회 (The Korean Society for Composite Materials)
권호 표지
DOI QR코드

DOI QR Code

유리섬유직물에 대한 수지의 젖음성 평가

Wettability Evaluation of Resin on the Glass Fabric

  • 발행 : 2011.04.30
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

에폭시 수지와 유리섬유직물 간의 젖음성을 분석하였다. 에폭시 수지와 산무수물 경화제의 혼합비는 당량비 1:0.5, 1:1, 1:1.2로 하였고, 촉매는 혼합된 수지의 0.lwt%로 첨가하였다. DSC 경화거동분석 결과 이 혼합 수지는 상온에서 함침이 가능하였다. 혼합 수지에 대해 유리평판에 놓여진 유리섬유직물 위에 수지 한 액적(방울)을 투하 후 시간에 따른 접촉각 변화를 측정하였다, 또한, 일정량의 에폭시 수지 액적을 투하시켜 시간에 따른 젖음면적 변화를 측정하였다, 접촉각, 액적높이, 순수 젖음면적, 젖음계수를 측정함으로써 유리섬유직물에 대한 에폭시 수지의 젖음성을 비교 평가하였다. 그 결과 당량비 1:1.2에서 유리섬유직물에 대한 젖음성이 가장 우수하였다.

Analysis of wettability between epoxy resin and glass fabric was studied. The mixing ratios of epoxy resin and anhydride hardener were varied as 1:0.5, l:l and l:1.2. Catalyst content was fixed as 0.1wt% of the mixed resin. A curing analysis by differential scanning calorimeter(DSC) showed a possible impregnation of the mixed resin at the room temperature. An effective contact angle of the mixed epoxy resin drop onto the glass fabric being preset on a flat glass plate was measured as a function of time. The wet area of the epoxy resin drop was also measured. Behaviors of the contact angle, the droplet height, the neat wet area and the coefficient of wettability were used to evaluate the wettability of the epoxy resin onto the glass fabric. It was concluded that the equivalent ratio of 1: 1.2 was the most suitable for the wettability.

키워드

참고문헌

  1. N. C. W. Judd and W. W. Wright, 1978, "Voids and their effects on the mechanical properties of composites-appraisal," SAMPLE Journal, January/February 10-4.
  2. S. F. M. Almeida, Z. S. N. Neto, 1994, "Effect of void content on the strength of composite laminates," Composite Structures, Vol. 28, No.2, pp. 139-148. https://doi.org/10.1016/0263-8223(94)90044-2
  3. J. D. Narn, S. J. Lee, K. J. Lee, 1995, "Resin Transfer molding for High Performance Composite Materials," Rheology [Korea], Vol. 7, No. 1, pp. 1-9.
  4. Neil Pearcea, Felicity Guildb and John Summers cales, 1997, "A study of the effects of convergent flow fronts on the properties of fibre reinforced composites produced by RTM," Composites part A, 29A, pp. 141-152.
  5. C. Y. Lee, C. H. Kim, K. M. Choi, C. Y. Park and O. C. Kweon, 2003, "Development of a Novel System for Measuring Sizing Degree Based on Contact Angle(I)," Journal of Korea TAPPI, Vol. 35(3), pp. 43-52.
  6. John P. Coulter and Selcuk I. Guceri, 1988, "Resin Impregnation During the Manufacturing of Composite Materials Subject to Prescribed Injection Rate," Journal of Reinforced Plastics and Composites, Vol. 7, No.3, pp. 200-219. https://doi.org/10.1177/073168448800700301
  7. 박수진, 석수자, 이재락, 김영근, 2004, "열잠재성 촉매개시제를 이용한 에폭시 수지의 경화거동 및 열안정성" 韓國複合材料學會誌, Vol. 17, No.5, pp. 47-53.
  8. D. S. Lee, T. S. Kim, B. S. Kim and J. H. Kim, 1996, "Cure Behavior of High Performance Epoxy/Polysulfone Blends (I)," Polymer, Vol. 20, No.3, pp. 403-411.
  9. D. S. Lee, T. S. Kim, B. S. Kim and J. H. Kim, 1996, "Cure Behavior of High Performance Epoxy/Polysulfone Blends (II)," Polymer, Vol. 20, No.3, pp. 412-418.
  10. iMTechnology (Image & Microscope Technnology), 2001, Measuring and Analyzing with ease (iSolution Lite).
  11. C. S. Wang and Stanley A. lobst, 2009, "Reducing Fiber Readout of Structural Composite Panels," Journal of Reinforced Plastics and Composites, Vol. 28, No. 19, pp. 2377-2386. https://doi.org/10.1177/0731684408092371
  12. K. J. Ahn, J. C. Seferis and J. C. Berg, 1991, "Simultaneous measurements of permeability and capillary pressure of thermosetting matrices in woven fabric reinforcements," Polymer Composites, Vol. 12(3), pp. 146-152. https://doi.org/10.1002/pc.750120303
  13. J. G. Williams, C. E. M. Morris and B. C. Ennis, 1974, "Liquid flow through aligned fiber beds," Polymer Engineering & Science, Vol. 14(6), pp. 413-319. https://doi.org/10.1002/pen.760140603
  14. C. H. Lee, S. H. Kim, S. W. Kim and K. J. Lee, 1998, "An Experimental Study on the Effect of Capillary Pressure on the Void Formation in Resin Transfer Molding Process," The Korean Journal of Rheology, Vol. 10, No. 4, pp. 185-194.
  15. G. W. Lee, M. H. Lee, S. W. Kim and K. J. Lee, 1995, "Experimental and Numerical Studies on the Flow Characteristics in Resin Transfer Molding Process," The Korean Journal of Rheology, Vol. 7, No.4, pp. 139-149.
  16. S. T. Nam, M. J. Han, H. S. Choi and Y. T. Park, 1998, "Effect of Physical Prooerties of Polymer Solution on the Thickness if Ultrathin Membrane Prepared by Water Casting Method," J. of Korean Ind. & Eng. Chemistry, Vol. 9, No.2, pp. 200-206.

피인용 문헌

  1. Optimum Mixing Ratio of Epoxy for Glass Fiber Reinforced Composites with High Thermal Stability vol.27, pp.4, 2014, https://doi.org/10.7234/composres.2014.27.4.168