DOI QR코드

DOI QR Code

연료 공급 및 S/C비에 따른 평판형 STR 반응기 성능 평가

The Performance Evaluation of Plate Type STR Reactor with Variation of S/C Ratio and Fuel Supply

  • 김헌주 (부경대학교 대학원 에너지시스템 공학과) ;
  • 허수빈 (부경대학교 대학원 에너지시스템 공학과) ;
  • 박재민 (부경대학교 대학원 에너지시스템 공학과) ;
  • 윤봉석 (부경대학교 대학원 에너지시스템 공학과) ;
  • 이도형 (부경대학교 기계공학부)
  • Kim, Hun-Ju (Dept. of Energy System Engineering, Grad. School of Pukyung National Univ.) ;
  • Heo, Su-Bin (Dept. of Energy System Engineering, Grad. School of Pukyung National Univ.) ;
  • Park, Jae-Min (Dept. of Energy System Engineering, Grad. School of Pukyung National Univ.) ;
  • Yoon, Bong-Seok (Dept. of Energy System Engineering, Grad. School of Pukyung National Univ.) ;
  • Lee, Do-Hyung (School of Mechanical Enginnering, Pukyung National Univ.)
  • 투고 : 2011.02.01
  • 심사 : 2011.04.22
  • 발행 : 2011.04.30

초록

According to the propagation of fuel cell system, the importance of that system efficiency is being magnified. Thus, the efficiency improvement of reformer which is the important factor of fuel cell system will be required. This study has been experimentally performed to evaluated the performance of plate type STR reactor. At first, we changed fuel flow rate (2, 3 and 4 l/min) in burner, and then we measured a proportion of hydrogen in produced gas through the STR reactor by G.C for evaluating the performance of plate type STR reactor in various fuel supply conditions. And we changed S/C ratio (2 and 4) and measured a proportion of hydrogen in produced gas through the STR reactor. As a results, condition at fuel flow rate 2 and 3 l/min could not be supplied amount of heat for STR sufficiently. Condition at fuel flow rate 4 l/min could supplied a heat excessively. And condition at S/C ratio 2, reaction occurred insufficiency. But condition at S/C ratio 4 was excess. From above, we found the optimum conditions that were fuel rate 3.5 l/min and S/C ratio 3.

키워드

참고문헌

  1. 서용석, 서동주, 서유택, 윤왕래, "메탄 수증기 개질반응기에서 연소, 열전달 및 개질반응 특성 연구", 제31회 KOSCO SYMPOSIUM 논문집, 2005, pp. 50-57.
  2. 박준근, 이신구, 임성광, 배중면, "천연가스로부터 수소를 생산하기 위한 수증기 개질기의 작동조건과 형상에 대한 수치해석 연구", 대한기계학회논문집 B권, 제33권, 제1호, 2009, pp. 60-67. https://doi.org/10.3795/KSME-B.2009.33.1.60
  3. 이경호, 권오채, "연료전지용 컴팩트형 개질기의 고성능화를 위한 고온 공기 연소 기술의 적용에 관한 연구", 한국수소 및 신에너지학회 논문집, 제16권, 제3호, 2005. 9, pp. 229-237.
  4. 오영삼, 송택용, 백영순, 최리상, "컴팩트형 수증기 개질장치 효율분석", 한국수소 및 신에너지학회 논문집(2002. 12), 제13권, 제4호, pp. 313-321.
  5. 이명용, 이지홍, 이상석, 이진석, 이도형, "다양한 형태의 버너를 이용한 수증기개질기의 고효율화 연구", 대한기계학회 2008년도 추계학술대회, 2008.11, pp. 2886-2791.
  6. 최종균, 정태용, 남진현, 신동훈, "수증기-메탄 개질반응 해석모델의 비교연구", 대한기계학회논문집 B권, 제32권, 제7호, 2008, pp. 497-503.
  7. 황정호, 노인규, 서동균, 신동훈, 최종균, 김형식, "고분자 전해질 막 연료전지를 위한 메탄 개질기에서 형상변화가 개질성능에 미치는 영향에 대한 연구", 한국 수소 및 신에너지 학회 논문집 제21권, 제5호, 2010.10, pp. 364-374.