DOI QR코드

DOI QR Code

Design and control of a proof-of-concept active jet engine intake using shape memory alloy actuators

  • Song, Gangbing (Department of Mechanical Engineering, University of Houston) ;
  • Ma, Ning (Department of Mechanical Engineering, University of Houston) ;
  • Li, Luyu (Department of Mechanical Engineering, University of Houston) ;
  • Penney, Nick (Ohio Aerospace Institute (OAI)) ;
  • Barr, Todd (Jackson & Tull Aerospace Division) ;
  • Lee, Ho-Jun (NASA Johnson Space Center) ;
  • Arnold, Steve (NASA Glenn Research Center)
  • 투고 : 2007.04.09
  • 심사 : 2010.03.19
  • 발행 : 2011.01.25

초록

It has been shown in the literature that active adjustment of the intake area of a jet engine has potential to improve its fuel efficiency. This paper presents the design and control of a novel proof-of-concept active jet engine intake using Nickel-Titanium (Ni-Ti or Nitinol) shape memory alloy (SMA) wire actuators. The Nitinol SMA material is used in this research due to its advantages of high power-to-weight ratio and electrical resistive actuation. The Nitinol SMA material can be fabricated into a variety of shapes, such as strips, foils, rods and wires. In this paper, SMA wires are used due to its ability to generate a large strain: up to 6% for repeated operations. The proposed proof-of-concept engine intake employs overlapping leaves in a concentric configuration. Each leaf is mounted on a supporting bar than can rotate. The supporting bars are actuated by an SMA wire actuator in a ring configuration. Electrical resistive heating is used to actuate the SMA wire actuator and rotate the supporting bars. To enable feedback control, a laser range sensor is used to detect the movement of a leaf and therefore the radius of the intake area. Due to the hysteresis, an inherent nonlinear phenomenon associated with SMAs, a nonlinear robust controller is used to control the SMA actuators. The control design uses the sliding-mode approach and can compensate the nonlinearities associated with the SMA actuator. A proof-of-concept model is fabricated and its feedback control experiments show that the intake area can be precisely controlled using the SMA wire actuator and has the ability to reduce the area up to 25%. The experiments demonstrate the feasibility of engine intake area control using an SMA wire actuator under the proposed design.

키워드

참고문헌

  1. Barooah, P. and Rey, N. (2002), "Closed loop control of a shape memory alloy actuation system for variable area fan nozzle", Proceedings of the SPIE International Symposium on Smart Structures and Materials, 4693, 384- 395.
  2. Barbarino, S., Pecora, R., Lecce, L., Concilio, A., Ameduri, S. and Calvi, E. (2009), "A novel SMA-based concept for airfoil structural morphing", J. Mater. Eng. Perform., 18(5-6), 696-705. https://doi.org/10.1007/s11665-009-9356-3
  3. Calkins, F.T., Mabe, J.H. and Butler, G.W. (2006), "Boeing's variable geometry chevron: Morphing aerospace structures for jet noise reduction", Proceedings of the SPIE - The International Society for Optical Engineering, 6171.
  4. Choi, S.B., Han, Y.M. and Cheong, C.C. (2001), "Force tracking control of a flexible gripper featuring shape memory alloy actuators", Mechatronics, 11(6), 677-690. https://doi.org/10.1016/S0957-4158(00)00034-9
  5. Dayananda, G.N., Varughese, B. and Subba Rao, M. (2007), "Shape memory alloy based smart landing gear for an airship", J. Aircraft, 44(5), 1469-1477. https://doi.org/10.2514/1.26811
  6. Epps, J. and Chopra, I. (2001), "In-flight tracking of helicopter rotor blades using shape memory alloy actuators", Smart Mater. Struct., 10(2001), 104-111. https://doi.org/10.1088/0964-1726/10/1/310
  7. Grant, D. and Hayward, V. (1997), "Variable structure control of shape memory alloy actuator", IEEE Contr. Syst. Mag., 17(3), 80-88. https://doi.org/10.1109/37.588180
  8. Majima, S., Kodama, K. and Hasegawa, T. (2001), "Modeling of shape memory alloy actuator and tracking control system with the model", IEEE T. Contr. Syst. T., 9(1), 54-59. https://doi.org/10.1109/87.896745
  9. Peng, F., Jiang, X., Hu, Y. and Ng, A. (2009), "Application of SMA in membrane structure shape control", IEEE T. Aero. Elec. Sys., 45(1), 85-93. https://doi.org/10.1109/TAES.2009.4805265
  10. Pitt, D.M., Dune, J.P., White, E.V. and Garcia, E. (2001), "Wind tunnel demonstration of the SMAPON smart inlet", Proceedings of the SPIE International Symposium on Smart Structures and Materials, 4332, 345-356.
  11. Rey, N.M., Tillman, G., Miller, R.M., Wynosky, T., Larkin, M.J., Flamm, J.D. and Bangert, L.S. (2001), "Shape memory alloy actuation for a variable area fan nozzle", Proceedings of the SPIE International Symposium on Smart Structures and Materials, 4332, 371-382.
  12. Song, G. and Mukherjee, R. (1998), "A comparative study of conventional non-smooth time-invariant and smooth time-varying robust compensators", IEEE T. Contr. Syst. T., 6(4), 571-576. https://doi.org/10.1109/87.701355
  13. Song, G. and Quinn, D. (2000), "Robust tracking control a shape memory alloy wire actuator", Proceedings of the Symposium on Control of Vibration and Noise at ASME International Mechanical Engineering Congress and Exposition.
  14. Strelec, J.K., Lagoudas, D.C., Khan, M.A. and Yen, J. (2003), "Design and implementation of a shape memory alloy actuated reconfigurable airfoil", J. Intel. Mater. Syst. Str., 14(4-5), 257-273. https://doi.org/10.1177/1045389X03034687
  15. Wolf, W. and Gunter, P. (2001), "Shape adaptive structures for smart airfoils", Proceedings of the IEEE International Conference on Multisensor Fusion and Integration for Intelligent Systems, Baden-Baden, Germany, August.

피인용 문헌

  1. Validation of a smart structural concept for wing-flap camber morphing vol.14, pp.4, 2014, https://doi.org/10.12989/sss.2014.14.4.659
  2. Morphing aircraft based on smart materials and structures: A state-of-the-art review vol.27, pp.17, 2016, https://doi.org/10.1177/1045389X16629569
  3. Control of an innovative super-capacitor-powered shape-memory-alloy actuated accumulator for blowout preventer vol.31, pp.01, 2017, https://doi.org/10.1142/S0217984916504261
  4. Experimental analyses of dynamical systems involving shape memory alloys vol.15, pp.6, 2015, https://doi.org/10.12989/sss.2015.15.6.1521
  5. Elucidating Multiscale Periosteal Mechanobiology: A Key to Unlocking the Smart Properties and Regenerative Capacity of the Periosteum? vol.19, pp.2, 2013, https://doi.org/10.1089/ten.teb.2012.0216
  6. Use of load generated by a shape memory alloy for its position control with a neural network estimator vol.20, pp.11, 2014, https://doi.org/10.1177/1077546313481000
  7. Servo control of an under actuated system using antagonistic shape memory alloy vol.14, pp.4, 2014, https://doi.org/10.12989/sss.2014.14.4.643
  8. Shape memory alloy actuator design: CASMART collaborative best practices and case studies vol.10, pp.1, 2014, https://doi.org/10.1007/s10999-013-9227-9
  9. Synthetic bio-actuators and their applications in biomedicine vol.7, pp.3, 2011, https://doi.org/10.12989/sss.2011.7.3.185
  10. Modular and versatile platform for the benchmarking of modern actuators for robots vol.11, pp.2, 2011, https://doi.org/10.12989/sss.2013.11.2.135
  11. Numerical Simulation and Experimental Study of a Simplified Force-Displacement Relationship in Superelastic SMA Helical Springs vol.19, pp.1, 2019, https://doi.org/10.3390/s19010050