Structural Engineering and Mechanics

Techno-Press (테크노프레스)
권호 표지
DOI QR코드

DOI QR Code

Mechanical behavior and buckling failure of sharp-notched circular tubes under cyclic bending

  • Lee, Kuo-Long (Department of Computer Application Engineering, Far East University)
  • Received : 2008.10.24
  • Accepted : 2009.11.13
  • Published : 2010.02.20
⟨ Previous Next ⟩

Abstract

In this paper, an experimental investigation of the mechanical behavior and buckling failure of sharp-notched circular tubes subjected to cyclic bending is discussed. The unnotched and sharp-notched circular tubes of SUS 304 stainless steel were tested under symmetric curvature-controlled cyclic bending. It was found from moment-curvature curves that the loops show cyclic hardening and gradually steady after a few cycles for all tested tubes. The ovalization-curvature curves show an unsymmetric, ratcheting and increasing manner with the number of cycles. In addition, it was found that six almost parallel lines corresponding to unnotched and five different notch-depth (0.2, 0.4, 0.6, 0.8 and 1.0 mm) tubes were noted from the experimental relationship between the cyclic controlled curvature and the number of cycles necessary to produce buckling on a log-log scale. An empirical formulation was proposed so that it could be used for simulating the aforementioned relationship. By comparing with the experimental finding, the simulation was in good agreement with the experimental data.

Keywords

References

  1. Chang, K.H. and Pan, W.F. (2008), "Mean moment effect of thin-walled tubes under cyclic bending", Struct. Eng. Mech., 28(5), 495-514. https://doi.org/10.12989/sem.2008.28.5.495
  2. Corona, E. and Kyriakides, S. (1988), "On the collapse of inelastic tubes under combined bending and pressure", Int. J. Solids Struct., 24(5), 505-535. https://doi.org/10.1016/0020-7683(88)90005-4
  3. Corona, E. and Kyriakides, S. (1991), "An experimental investigation of the degradation and buckling of circular tubes under cyclic bending and external pressure", Thin Wall. Struct., 12, 229-263. https://doi.org/10.1016/0263-8231(91)90048-N
  4. Corona, E. and Vaze, S. (1996), "Buckling of elastic-plastic square tubes under bending", Int. J. Mech. Sci., 38(7), 753-775. https://doi.org/10.1016/0020-7403(95)00081-X
  5. Elchalakani, M., Zhao, X.L. and Grzebieta, R.H. (2002), "Plastic mechanism analysis of circular tubes under pure bending", Int. J. Mech. Sci., 44, 1117-1143. https://doi.org/10.1016/S0020-7403(02)00017-6
  6. Elchalakani, M., Zhao, X.L. and Grzebieta, R.H. (2004), "Concrete-filled circular tubes subjected to constant amplitude cyclic pure bending", Eng. Struct., 26, 2125-2135. https://doi.org/10.1016/j.engstruct.2004.07.012
  7. Jiao, H. and Zhao, X.L. (2004), "Section slenderness limits of very high strength circular steel tubes in bending", Thin Wall. Struct., 42, 1257-1271. https://doi.org/10.1016/j.tws.2004.03.020
  8. Kyriakides, S. and Shaw, P.K. (1982), "Response and stability of elastoplastic circular pipes under combined bending and external pressure", Int. J. Solids Struct., 18(11), 957-973. https://doi.org/10.1016/0020-7683(82)90086-5
  9. Kyriakides, S. and Shaw, P.K. (1987), "Inelastic buckling of tubes under cyclic loads", ASME J. Press. Vessel Technol., 109, 169-178. https://doi.org/10.1115/1.3264891
  10. Lee, K.L., Pan, W.F. and Hsu, C.M. (2004), "Experimental and theoretical evaluations of the effect between diameter-to-thickness ratio and curvature-rate on the stability of circular tubes under cyclic bending", JSME Int. J. Series A, 47(2), 212-222. https://doi.org/10.1299/jsmea.47.212
  11. Lee, K.L., Pan, W.F. and Kuo, J.N. (2001), "The influence of the diameter-to-thickness ratio on the stability of circular tubes under cyclic bending", Int. J. Solids Struct., 38, 2401-2413. https://doi.org/10.1016/S0020-7683(00)00116-5
  12. Pan, W.F. and Fan, C.H. (1998), "An experimental study on the effect of curvature-rate at preloading stage on subsequent creep or relaxation of thin-walled tubes under pure bending", JSME Int. J. Series A, 41(4), 525-531. https://doi.org/10.1299/jsmea.41.525
  13. Pan, W.F. and Her, Y.S. (1998), "Viscoplastic collapse of thin-walled tubes under cyclic bending", J. Eng. Mat. Tech., 120, 287-290. https://doi.org/10.1115/1.2807015
  14. Pan, W.F., Wang, T.R. and Hsu, C.M. (1998), "A curvature-ovalization measurement apparatus for circular tubes under cyclic bending", Exp. Mech., 38(2), 99-102. https://doi.org/10.1007/BF02321651
  15. Shaw, P.K. and Kyriakides, S. (1985), "Inelastic analysis of thin-walled tubes under cyclic bending", Int. J. Solids Struct., 21(11), 1073-1110. https://doi.org/10.1016/0020-7683(85)90044-7
  16. Vaze, S. and Corona, E. (1998), "Degradation and collapse of square tubes under cyclic bending", Thin Wall. Struct., 31, 325-341. https://doi.org/10.1016/S0263-8231(98)00018-4

Cited by

  1. On the response of dented stainless-steel pipes subject to cyclic bending moments and its prediction vol.99, 2016, https://doi.org/10.1016/j.tws.2015.10.017
  2. Failure life estimation of sharp-notched circular tubes with different notch depths under cyclic bending vol.60, pp.3, 2016, https://doi.org/10.12989/sem.2016.60.3.387
  3. Springback FE modeling of titanium alloy tubes bending using various hardening models vol.56, pp.3, 2015, https://doi.org/10.12989/sem.2015.56.3.369
  4. Ratcheting response of dented pipes under monotonic and cyclic axial loadings vol.49, pp.2, 2014, https://doi.org/10.1177/0309324713494197
  5. Collapse of Sharp-Notched 6061-T6 Aluminum Alloy Tubes Under Cyclic Bending vol.16, pp.07, 2016, https://doi.org/10.1142/S0219455415500352
  6. Mean moment effect on sharp-notched circular tubes under cyclic bending vol.27, pp.9, 2013, https://doi.org/10.1007/s12206-013-0712-8
  7. Viscoplastic collapse of sharp-notched circular tubes under cyclic bending vol.26, pp.6, 2013, https://doi.org/10.1016/S0894-9166(14)60007-0
  8. Response of sharp-notched circular tubes under bending creep and relaxation vol.1, pp.2, 2014, https://doi.org/10.1299/mej.2014smm0005
  9. Bending ratcheting tests of Z2CND18.12 stainless steel vol.35, pp.1, 2012, https://doi.org/10.1016/j.ijfatigue.2011.04.008
  10. Collapse of elliptical-notched circular tubes under cyclic bending vol.39, pp.1, 2016, https://doi.org/10.1080/02533839.2015.1070689
  11. The Influence of Diameter-to-Thickness Ratios on the Response and Collapse of Sharp-Notched Circular Tubes under Cyclic Bending vol.28, pp.03, 2012, https://doi.org/10.1017/jmech.2012.55
  12. The Influence of Notch Depth on the Response of Local Sharp-Notched Circular Tubes under Cyclic Bending vol.02, pp.06, 2014, https://doi.org/10.4236/jamp.2014.26040
  13. Effects of Notch Depth and Direction on Stability of Local Sharp-Notched Circular Tubes Subjected to Cyclic Bending 2018, https://doi.org/10.1142/S0219455418500992
  14. Finite element analysis on the response of 6061-T6 aluminum alloy tubes with a local sharp cut under cyclic bending vol.18, pp.7, 2016, https://doi.org/10.21595/jve.2016.17425
  15. Growing and critical ovalization for sharp-notched 6061-T6 aluminum alloy tubes under cyclic bending vol.39, pp.8, 2016, https://doi.org/10.1080/02533839.2016.1225516
  16. Finite Element Analysis on the Response of Local Sharp-Notched Circular Tubes under Cyclic Bending vol.626, pp.1662-9795, 2014, https://doi.org/10.4028/www.scientific.net/KEM.626.34
  17. Experimental and numerical investigations on the ratcheting characteristics of cylindrical shell under cyclic axial loading vol.44, pp.6, 2010, https://doi.org/10.12989/sem.2012.44.6.753
  18. Out-of-plane ductile failure of notch: Evaluation of Equivalent Material Concept vol.75, pp.5, 2020, https://doi.org/10.12989/sem.2020.75.5.559
  19. Influence of redundant hole on the degradation and failure of round-hole tubes under cyclic bending vol.44, pp.5, 2021, https://doi.org/10.1080/02533839.2021.1919565
  20. Response of round-hole tubes submitted to pure bending creep and pure bending relaxation vol.13, pp.9, 2010, https://doi.org/10.1177/16878140211049124
  21. Mean curvature effect on the response and failure of round-hole tubes submitted to cyclic bending vol.13, pp.11, 2021, https://doi.org/10.1177/16878140211062273