Structural Engineering and Mechanics

  • 제34권2호
  • /
  • Pages.143-157
  • /
  • 2010
  • /
  • 1225-4568(pISSN)
  • /
  • 1598-6217(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Stress concentrations around a circular hole in an infinite plate of arbitrary thickness

  • Dai, Longchao (Institute of Structure and Strength, Nanjing University of Aeronautics and Astronautics) ;
  • Wang, Xinwei (Institute of Structure and Strength, Nanjing University of Aeronautics and Astronautics) ;
  • Liu, Feng (College of Aviation Engineering, Civil Aviation Flight University of China)
  • 투고 : 2008.04.15
  • 심사 : 2009.11.04
  • 발행 : 2010.01.30
⟨ 이전 논문 다음 논문 ⟩

초록

This paper presents theoretical solutions for the three-dimensional (3D) stress field in an infinite isotropic elastic plate containing a through-the-thickness circular hole subjected to far-field in-plane loads by using Kane and Mindlin's assumption. The dangerous position, where the premature fracture or failure of the plate will take place, the expressions of the tangential stress at the surface of the hole and the out-of-plane stress constraint factor are found in a concise, explicit form. Based on the present theoretical solutions, a comprehensive analysis is performed on the deviated degree of the in-plane stresses from the related plane stress solutions, stress concentration and out-of-plane constraint, and the emphasis has been placed on the effects of the plate thickness, Poisson's ratio and the far-field in-plane loads on the stress field. The analytical solution shows that the effects of the plate thickness and Poisson's ratio on the deviation of the 3D in-plane stress components is obvious and could not be ignored, although their effects on distributions of the in-plane stress components are slight, and that the effect of the far-field in-plane loads is just on the contrary of that of the above two. When only the shear stress is loaded at far field, the stress concentration factor reach its peak value about 8.9% higher than that of the plane stress solutions, and the out-of-plane stress constraint factor can reach 1 at the surface of the hole and is the biggest among all cases considered.

키워드

참고문헌

  1. Chaudhuri, R.A. (2003a), "Three-dimensional asymptotic stress field in the vicinity of the circumferential line of intersection of an inclusion and plate surface", Int. J. Fract., 119, 195-222. https://doi.org/10.1023/A:1023900725034
  2. Chaudhuri, R.A. (2003b), "Three-dimensional asymptotic stress field in the vicinity of the line of intersection of a circular cylindrical through/part-through open/rigidly plugged hole and a plate", Int. J. Fract., 122, 65-88. https://doi.org/10.1023/B:FRAC.0000005375.68272.c5
  3. Filippi, S., Lazzarin, P. and Tovo, R. (2002), "Developments of some explicit formulas useful to describe elastic stress fields ahead of notches in plates", Int. J. Solids Struct., 39, 4543-4565. https://doi.org/10.1016/S0020-7683(02)00342-6
  4. Filippo, B., Lazzarin, P. and Wang, C.H. (2004), Three-dimensional linear elastic distributions of stress and strain energy density ahead of V-shaped notches in plates of arbitrary thickness", Int. J. Fract., 127, 265-281. https://doi.org/10.1023/B:FRAC.0000036846.23180.4d
  5. Folias, E.S. (1975), "On the three-dimensional theory of cracked plates", J. Appl. Mech., ASME, 42, 663-674. https://doi.org/10.1115/1.3423660
  6. Folias, E.S. and Wang, J.J. (1990), "On the three-dimensional stress field around a circular hole in a plate of arbitrary thickness", Comput. Mech., 6, 379-391. https://doi.org/10.1007/BF00350419
  7. Jin, Z.H. and Hwang, K.C. (1989), "An analysis of three-dimensional effects near the tip of a crack in an elastic plate", Acta. Mech. Solida Sin., 2, 387-401.
  8. Jin, Z.H. and Batra, R.C. (1997), "A crack at the interface between a Kane-Mindlin plate and a rigid substrate", Eng. Fract. Mech., 57, 343-354. https://doi.org/10.1016/S0013-7944(97)00036-2
  9. Kane, T.R. and Mindlin, R.D. (1956), "High-frequency extensional vibrations of plates", J. Appl. Mech., ASME, 23, 277-283.
  10. Krishnaswamy, S., Jin, Z.H. and Batra, R.C. (1998), "Stress concentration in an elastic Cosserat plate undergoing extensional deformations", J. Appl. Mech., ASME, 65, 66-70. https://doi.org/10.1115/1.2789047
  11. Kotousov, A. (2007), "Fracture in plates of finite thickness", Int. J. Solids Struct., 44, 8259-8273. https://doi.org/10.1016/j.ijsolstr.2007.06.011
  12. Kotousov, A. and Wang, C.H. (2002a), "Three-dimensional stress constraint in an elastic plate with a notch", Int. J. Solids Struct., 39, 4311-4326. https://doi.org/10.1016/S0020-7683(02)00340-2
  13. Kotousov, A. and Wang, C.H. (2002b), "Three-dimensional solutions for transversally isotropic plates", Compos. Struct., 57, 445-452. https://doi.org/10.1016/S0263-8223(02)00112-5
  14. Kotousov, A. and Wang, C.H. (2002c), "Fundamental solutions for the generalized plane strain theory", Int. J. Eng. Sci., 40, 1775-1790. https://doi.org/10.1016/S0020-7225(02)00041-1
  15. Lazzarin, P. and Tovo, R. (1996), "A unified approach to the evaluation of linear elastic stress fields in the neighborhood of cracks and notches", Int. J. Fract., 78, 3-19. https://doi.org/10.1007/BF00018497
  16. Li, Z. and Guo, W. (2001), "Three-dimensional elastic stress fields ahead of blunt V-notches in finite thickness plates", Int. J. Fract., 107, 53-71. https://doi.org/10.1023/A:1026586819885
  17. Li, Z., Guo, W. and Kuang, Z. (2000), "Three-dimensional elastic stress fields near notches in finite thickness plates", Int. J. Solids Struct., 37, 7617-7631. https://doi.org/10.1016/S0020-7683(99)00311-X
  18. Penado, F.E. and Folias, E.S. (1989), "The three-dimensional stress field around a cylindrical inclusion in a plate of arbitrary thickness", Int. J. Fract., 39, 129-146. https://doi.org/10.1007/BF00047446
  19. Sadowsky, M.A. and Sternberg, E. (1949), Stress concentration around an ellipsoidal cavity", J. Appl. Mech., ASME, 16, 149-157.
  20. Sternberg, E. and Sadowsky, M.A. (1949), "Three-dimensional solution for the stress concentration around a circular hole in a plate of arbitrary thickness", J. Appl. Mech., ASME, 16, 27-38.
  21. Yang, J. and Guo, S. (2005), "On using the Kane-Mindlin theory in the analysis of crack in plates", Int. J. Fract., 133, L13-L17. https://doi.org/10.1007/s10704-005-7119-1
  22. Yang, W. and Freund, L.B. (1985), "Transverse shear effects for through-crack in an elastic plate", Int. J. Solids Struct., 21, 977-994. https://doi.org/10.1016/0020-7683(85)90111-8
  23. Yang, Z., Kim, C.B., Cho, C. and Beom, H.G. (2008), "The concentration of stress and strain in finite thickness elastic plate containing a circular hole", Int. J. Solids Struct., 45, 713-731. https://doi.org/10.1016/j.ijsolstr.2007.08.030
  24. Young, C.K. and Sternberg, E. (1966), "Three-dimensional stress concentration around a cylindrical hole in a semi-infinite elastic body", J. Appl. Mech., ASME, 33, 855-865. https://doi.org/10.1115/1.3625193