소성∙가공 (Transactions of Materials Processing)

  • 제19권7호
  • /
  • Pages.416-422
  • /
  • 2010
  • /
  • 1225-696X(pISSN)
  • /
  • 2287-6359(eISSN)
한국소성∙가공학회 (The Korean Society for Technology of Plasticity and materials processing)
권호 표지
DOI QR코드

DOI QR Code

{10ī2} 쌍정 특성이 AZ31 마그네슘 합금 압연재의 변형거동에 미치는 영향

Effect of {10ī2} Twinning Characteristics on the Deformation Behavior of Rolled AZ31 Mg Alloy

  • 박성혁 (포항공과대학교 신소재공학과) ;
  • 홍성구 (한국표준과학연구원) ;
  • 이정훈 (포항공과대학교 신소재공학과) ;
  • 이종수 (포항공과대학교 신소재공학과)
  • 투고 : 2010.08.16
  • 심사 : 2010.09.28
  • 발행 : 2010.11.01
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

The $\{10\bar{1}2\}$ twinning characteristics, such as active twin variants, volume fraction of twins with strain, twin morphology, twin texture and angle relationship between twins, were dependent on the activation mode (i.e., tension parallel to the caxis or compression perpendicular to the c-axis). The selection criterion of active twin variants was governed by the Schmid law. This activation of selected twin variants depending on the activation mode consequently caused a totally different plastic deformation behavior in two activation modes. The differences in the deformation characteristics, such as flow stress and work hardening rate, between both activation modes were explained in relation with activation stresses for slips and twinning, relative activities of twinning and slips during plastic deformation, grain refining effect by twin boundaries (Hall-Petch effect), and twinning-induced change in activities of slips.

키워드

참고문헌

  1. B. L. Mordike, T. Ebert, 2001, Magnesium: Properties-applications-potential, Mater. Sci. Eng. A, Vol. 302, pp. 37-45. https://doi.org/10.1016/S0921-5093(00)01351-4
  2. X.Y. Lou, et al., 2007, Hardening evolution of AZ31B Mg sheet, Int. J. Plast., Vol. 23, pp. 44-86. https://doi.org/10.1016/j.ijplas.2006.03.005
  3. H. Mayer, M. Papakyriacou, B. Zettl, S. E. Stanzl-Tschegg, 2003, Influence of porosity on the fatigue limit of die cast magnesium and aluminum alloys, Int. J. Fatigue, Vol. 25, pp. 245-256. https://doi.org/10.1016/S0142-1123(02)00054-3
  4. J.P. Weiler, et al., 2005, Relationship between internal porosity and fractures strength of die-cast magnesium AM60B alloy, Mater. Sci. Eng. A, Vol. 395, pp. 315-322. https://doi.org/10.1016/j.msea.2004.12.042
  5. S. G. Lee, et al., 2005, Variability in the tensile ductility of high-pressure die-cast AM50 Mg-alloy, Scripta Mater., Vol. 53, pp. 851-856. https://doi.org/10.1016/j.scriptamat.2005.06.002
  6. Wu L, et al., 2008, Twinning-detwinning behavior during the strain-controlled low-cycle fatigue testing of a wrought magnesium alloy, ZK60A, Acta Mater., Vol. 56, pp. 688-695. https://doi.org/10.1016/j.actamat.2007.10.030
  7. S. H. Park, S-G Hong, C. S. Lee, 2010, Effect of anisotropy on the low-cycle fatigue behavior of rolled AZ31 magnesium alloy, Mater. Sci. Eng. A, Vol. 527, pp. 417-423. https://doi.org/10.1016/j.msea.2009.08.044
  8. S. H. Park, S-G Hong, C. S. Lee, 2010, Role of initial {10-12} twin in the fatigue behavior of rolled Mg-3Al-1Zn alloy, Scripta Mater., Vol. 62, pp. 666-669. https://doi.org/10.1016/j.scriptamat.2010.01.021
  9. Y. N. Wang, J. C. Huang, 2007, The role of twinning and untwinning in yielding behavior in hot-extruded Mg-Al-Zn alloy, Acta Mater., Vol. 55, pp. 897-905. https://doi.org/10.1016/j.actamat.2006.09.010
  10. Y. Chino, K. Kimura, M. Mabuchi, 2009, Deformation characteristics at room temperature under biaxial tensile stress in textured AZ31 Mg alloy sheets, Acta Mater., Vol. 57, pp. 1476-1485. https://doi.org/10.1016/j.actamat.2008.11.033
  11. M. R. Barnett, Z. Keshavarz, A. G. Beer, D. Atwell, 2004, Influence of grain size on the compression deformation of wrought Mg-3Al-1Zn, Acta Mater., Vol. 52, pp. 5093-5103 https://doi.org/10.1016/j.actamat.2004.07.015
  12. Robert E. Reed-Hill, R. Abbaschian, 1991, Physical Metallurgy Principles, PWS publishing company, Boston.
  13. S. H. Park, S-G Hong, C. S. Lee, 2010, Activation mode dependent {10-12} twinning characteristics in a polycrystalline magnesium alloy, Scripta Mater., Vol. 62, pp. 202-205. https://doi.org/10.1016/j.scriptamat.2009.10.027

피인용 문헌

  1. Texture Evolution of Extruded AZ80 Mg Alloy under Various Compressive Forming Conditions vol.21, pp.4, 2012, https://doi.org/10.5228/KSTP.2012.21.4.240
  2. The Temperature Dependent C-H/V Constitutive Modeling for Magnesium Alloy Sheet vol.21, pp.4, 2012, https://doi.org/10.5228/KSTP.2012.21.4.221