한국유체기계학회 논문집 (The KSFM Journal of Fluid Machinery)

한국유체기계학회 (Korean Society for Fluid machinery)
권호 표지
DOI QR코드

DOI QR Code

가스터빈 입구에서의 유동 및 스칼라 분포 특성

Measurement of Flow and Scalar Distribution at Gas Turbine Inlet Section

  • 투고 : 2010.06.29
  • 심사 : 2010.07.19
  • 발행 : 2010.08.01
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

The goal of paper is to investigate the flow and scalar distribution through the HP Nozzle Guide Vane (NGV) passage. Flow and scalar distribution measurement are conducted by using 5-hole pressure probe and $CO_2$ tracing technique, respectively. Three different experimental cases are considered depending on cooling flow condition. The result shows that the vortical secondary flow patterns are observed clearly and these flow characteristics maintain through the NGV passage regardless of cooling flow injection. Compared to center region, the high axial velocity flow is observed near wall region due to cooling flow injection. Without cooling flow, the $CO_2$ (scalar) distribution becomes to be uniform quickly due to the strong flow mixing phenomenon. However, in cases of cooling flow, scalar distribution is significantly non-uniform.

키워드

참고문헌

  1. Kerrebrock, J. L. and Mikolajczak, A. A., 1970, “Intra-Stator Transport of Rotor Wakes and Its Effect on Compressor Performance”, ASME J. of Engineering for Gas Turbine and Power, Vol. 92, No. 4, pp. 359-370. https://doi.org/10.1115/1.3445365
  2. Butler,T .L., Sharma, O. P., Jopslyn, H. D. and Dring R. P., 1989, “Redistribution of Inlet Temperature Distortion in an Axial Flow Turbine Stage”, AIAA J. of Propulsion and Power, Vol. 5, No. 1, pp. 64-71. https://doi.org/10.2514/3.23116
  3. Shang, T. and Epstein, A. H., 1997, “Analysis of hot streak effects on turbine rotor heat load”, ASME J. of Turbomachinery, Vol. 119, No. 3, pp. 544-553. https://doi.org/10.1115/1.2841156
  4. Varadarajan, K. and Bogard, D. G., 2004, “Effect of hot streaks on adiabatic effectiveness for a film cooled turbine vane,” ASME Turbo Expo 2004, Paper No. GT-2004-54016. https://doi.org/10.1115/GT2004-54016
  5. Povey T., Chana, K. S., Jones T. V. and Hurrion J, 2005, “The Effect of Hot-streaks on HP Vane Surface and Endwall Heat Transfer : an Experimental and Numerical Study”, ASME Turbo Expo 2005, Paper No. GT2005-69066. https://doi.org/10.1115/GT2005-69066
  6. Dorney, D. J. and Sondak, D. L., 2000, “Effects of tip clearance on hot streak migration in a high-subsonic single stage turbine,” ASME Turbo Expo 2000, Paper No. 2000-GT-441.
  7. Sondak, D. L., Gupta, V., Orkwis, P. D. and Dorney, D., J., 2002, “Effects of Blade Count on Linearized and Nonlinear Hot Streak Clocking Simulations”, AIAA J. Propulsion & Power, Vol. 18, No. 6, pp. 1273-1279. https://doi.org/10.2514/2.6063
  8. He, L., Menshikova, V. and Haller, B. R., 2004, “Influence of hot streak circumferential length scale in transonic turbine stage,” ASME Turbo Expo 2004, ASME Paper No. GT-2004-53370.
  9. Denman P. A., 2007, Lean Module Scaling EFE Combustion System Aerodynamics; Part I Fuel Injector Scalar Mixing Experiments, Loughborough University report, TT07R03.
  10. Abernethy, R. B., Benedict, R. P., and Dowdell, R. B., 1985, “Measurement Uncertainty,” J. of Fluid Engineering, Vol. 107, pp. 161-164. https://doi.org/10.1115/1.3242450