Textile Science and Engineering (한국섬유공학회지)

The Korean Fiber Society (한국섬유공학회)
권호 표지

Interfacial Adhesion Properties of Plasma Treated Aramid Fiber with Chloroprene Rubber

아라미드 섬유의 플라즈마 처리에 따른 클로로프렌 고무와의 계면접착 특성

  • Lee, Tae-Sang (BK21 FTIT, Department of Advanced Organic Materials & Textile System Engineering, Chungnam National University) ;
  • Kim, Book-Sung (BK21 FTIT, Department of Advanced Organic Materials & Textile System Engineering, Chungnam National University) ;
  • Choi, Han-Na (BK21 FTIT, Department of Advanced Organic Materials & Textile System Engineering, Chungnam National University) ;
  • Lee, Kee-Yoon (Department of Polymer Science and Engineering, Chungnam National University) ;
  • Lee, Seung-Goo (BK21 FTIT, Department of Advanced Organic Materials & Textile System Engineering, Chungnam National University)
  • 이태상 (BK21 FTIT, 충남대학교 유기소재섬유시스템공학과) ;
  • 김북성 (BK21 FTIT, 충남대학교 유기소재섬유시스템공학과) ;
  • 최한나 (BK21 FTIT, 충남대학교 유기소재섬유시스템공학과) ;
  • 이기윤 (충남대학교 고분자공학과) ;
  • 이승구 (BK21 FTIT, 충남대학교 유기소재섬유시스템공학과)
  • Received : 2010.04.02
  • Accepted : 2010.06.04
  • Published : 2010.06.30
⟨ Previous Next ⟩

Abstract

The interfacial adhesion between the chloroprene rubber (CR) and aramid fiber treated with cold plasma was investigated. The surface properties of aramid fiber and CR were characterized by scanning electron microscopy (SEM), atomic force microscopy (AFM) and dynamic contact angle (DCA) measurements. The surface morphology of the aramid fiber changed with the plasma treatment time, power and gas flow rate. The interfacial shear strength, between the plasma treated aramid fiber and CR, was calculated using the pull-out test results. The interfacial adhesion properties of the aramid fabric/CR composite were determined using a T-peel test. Consequently, the strong interaction between the plasma treated aramid fiber and CR matrix improved the interfacial adhesion strength of the composite.

Keywords

References

  1. K. Tanaka, K. Minoshima, T. Oya, and K. Komai, "Influences of Stress Waveform and Wet Environment on Fatigue Fracture Behavior of Aramid Single Fiber", Comp Sci Tech, 2004, 64, 1531-1537. https://doi.org/10.1016/j.compscitech.2003.11.004
  2. L. Liu, Y. D. Huang, Z. Q. Zhang, Z. X. Jiang, and L. N. Wu, "Ultrasonic Treatment of Aramid Fiber Surface and Its Effect on the Interface of Aramid/Epoxy Composites", Appl Surface Sci, 2008, 254, 2594-2599. https://doi.org/10.1016/j.apsusc.2007.09.091
  3. J.-M. Park, D.-S. Kim, and S.-R. Kim, "Improvement of Interfacial Adhesion and Nondestructive Damage Evaluation for Plasma-Treated PBO and Kevlar Fibers/Epoxy Composites Using Micromechanical Techniques and Surface Wettability", J Colloid Interf Sci, 2003, 264, 431-445. https://doi.org/10.1016/S0021-9797(03)00419-3
  4. Y. Kondo, K. Miyazaki, Y. Yamaguchi, T. Sasaki, S.Irie, and K. Sakurai, "Mechanical Properties of Fiber Reinforced Styrene-Butadiene Rubbers Using Surface-modified UHMWPE Fibers under EB Irradiation", Euro Polym J, 2006, 42, 1008- 1014. https://doi.org/10.1016/j.eurpolymj.2005.11.025
  5. A. Saritha Chandran and Sunil K. Narayanankutty, "An Elastomeric Conducting Composite Based on Polyaniline Coated Nylon Fiber and Chloroprene Rubber", Euro Polym J, 2008, 44, 2418-2429. https://doi.org/10.1016/j.eurpolymj.2008.05.012
  6. P. Sae-oui, C. Sirisinha, U. Thepsuwan, and K. Hatthapanit, "Dependence of Mechanical and Aging Properties of Chloroprene Rubber on Silica and Ethylene Thiourea Loadings", Euro Polym J, 2007, 43, 185-193. https://doi.org/10.1016/j.eurpolymj.2006.10.015
  7. H. Ismail and H. C. Leong, "Curing Characteristics and Mechanical Properties of Natural Rubber/Chloroprene Rubber and Epoxidized Natural Rubber/Chloroprene Rubber Blends", Polymer Testing, 2001, 20, 509-516. https://doi.org/10.1016/S0142-9418(00)00067-2
  8. G. M. Wu, "Oxygen Plasma Treatment of High Performance Fibers for Composites", Mater Chem Phys, 2004, 85, 81-87. https://doi.org/10.1016/j.matchemphys.2003.12.004
  9. J.-M. Park, D.-S. Kim, and S.-R. Kim, ''Nondestructive Microfailure and Interfacial Evaluation of Plasma-Treated PBO and Kevlar Fibers/Epoxy Composites Using Micromechanical Test and Acoustic Emission", J Korean Comp Mater, 2003, 6(4), 74-79.
  10. L. Goglio, M. Rossetto, and E. Dragoni, "Design of Adhesive Joints Based on Peak Elastic Stresses", Inter J Adhesion & Adhesives, 2008, 28, 427-435. https://doi.org/10.1016/j.ijadhadh.2008.04.001
  11. H. F. Zhao, M. Chen, and Y. Jin, "Determination of Interfacial Properties between Metal Film and Ceramic Substrate with an Adhesive Layer", Materials & Design, 2009, 30, 154-159. https://doi.org/10.1016/j.matdes.2008.04.035
  12. D. W. Hess and D. B. Graves, "Plasma-Enhanced Etching and Deposition, Microelectronics Processing: Chemical Engineering Aspects", American Chemical Society, Washington D.C., 1989, pp.376-440.