DOI QR코드

DOI QR Code

입방정계 순 금속 Fe, Cu의 미끄럼 마멸 거동

Sliding Wear Behavior of Pure Metal, Fe and Cu Having a Cubic Crystal System

  • 이슬기 (국민대학교 신소재공학부) ;
  • 김용석 (국민대학교 신소재공학부)
  • 투고 : 2010.08.16
  • 심사 : 2010.09.07
  • 발행 : 2010.10.01

초록

Dry sliding wear behavior of pure Fe and Cu which have BCC and FCC crystal structure, respectively, was investigated. The wear characteristics of the pure metals with different crystal structure were compared. Dry sliding wear tests were carried out using a pin-on-disk wear tester at various loads under the constant sliding speed condition of 0.15 m/s against a silica ball at room temperature. Sliding distance was fixed as 600 m for all wear tests. Wear rate of a specimen was calculated by dividing the weight loss of the specimen after the test by the specific gravity and sliding distance. Worn surfaces and wear debris were analyzed by SEM. The wear of both pure Fe and Cu proceeded with surface deformation, resulting in similar wear rates despite of their structure difference under the current test conditions. Wear rates of both metals were low if the surface deformation due to wear forms thick surface-deformation layer that is strain hardened beneath the wearing surface. The pure Cu specimens showed a lot of oxides on the worn surface when tested at low loads less than 5 N, which resulted in very low wear rate.

키워드

참고문헌

  1. R. G. Bayer, 1994, Mechanical Wear Prediction and Prevention, Marcel Dekker, Inc., New York, pp.1-3.
  2. K.-H. Zum Gahr, 1987, Microstructure and Wear of Materials, Elsevier, Amsterdam, pp. 393-397.
  3. H. S. Yu, S. K. Yi, D. H. Shin, Y.-S. Kim, 2007, Sliding Wear Mechanism of Ultra-fine Grained Low Carbon Dual Phase Steel as a Function of Applied Load, Trans. Mater. Process., Vol. 16, No. 4, pp. 299-303. https://doi.org/10.5228/KSPP.2007.16.4.299
  4. Y.-S. Kim, H. S. Yu, D. H. Shin, 2009, Low Slidingwear Resistance of Ultrafine-grained Al Alloys and Steel undergone Severe Plastic Deformation, Int. J. Mater. Res., Vol. 100, No. 6, pp. 871-874. https://doi.org/10.3139/146.110109
  5. Y. S. Zhang, Z. Han, K. Wang, K. Lu, Wear, 2006, Friction and Wear Behaviors of Nanocrystalline Surface Layer of Pure Copper, Vol. 260, pp. 942-948. https://doi.org/10.1016/j.wear.2005.06.010
  6. S. D. Kim, S. J. Kim, Y.-S. Kim, 2006, Sliding Wear Mechanism of the High-nitrogen Austenitic 18Cr-18Mn-2Mo-0.9N Steel, Trans. Mater. Process., Vol. 15, pp. 112-117. https://doi.org/10.5228/KSPP.2006.15.2.112
  7. D. H. Buckley, R. I. Johnson, Wear, 1968, The Influence of Crystal Structure and Some Properties of Hexagonal Metals on Friction and Adhesion, Vol. 11, No. 6, pp. 405-419. https://doi.org/10.1016/0043-1648(68)90550-4
  8. M. D. Hanna, J. T. Carter, M. S. Rashid, Wear, 1997, Sliding Wear and Friction Characteristics of Six Znbased Die-casting Alloys, Vol. 11-21, pp. 11-21.
  9. T. Akagak, D. A. Rigney, Wear, 1991, Sliding Friction and Wear of Metals in Vacuum, Vol. 149, No. 1-2, pp. 353-374. https://doi.org/10.1016/0043-1648(91)90385-8
  10. A. F. Smith, Wear, 1984, The Friction and Sliding Wear of Unlubricated 316 Stainless Steel at Room Temperature in Air, Vol. 96, No. 3, pp. 301-318. https://doi.org/10.1016/0043-1648(84)90043-7
  11. J. E. Lee, Y.-S. Kim, T.-W. Kim, 2008, Comparing Sliding-Wear Characteristics of the Electro-pressure Sintered and Wrought Cobalt, Int. J. Modern Phy. B(IJMPB), Vol. 22, No. 31/32, pp. 6127-6132. https://doi.org/10.1142/S0217979208051686

피인용 문헌

  1. Sliding Wear Behavior of AISI 52100 Steel with Pearlitic and Bainitic Microstructures vol.20, pp.7, 2011, https://doi.org/10.5228/KSTP.2011.20.7.479