DOI QR코드

DOI QR Code

Cracking Near a Hole on a Heat- Resistant Alloy Subjected to Thermo-Mechanical Cycling

열 및 기계적 반복하중 하의 내열금속 표면 홀 주변 산화막의 변형 및 응력해석

  • Li, Feng-Xun (Dept. of Mechanical Systems Engineering, Chonnam Nat'l Univ.) ;
  • Kang, Ki-Ju (Dept. of Mechanical Systems Engineering, Chonnam Nat'l Univ.)
  • 이봉훈 (전남대학교 기계시스템공학부) ;
  • 강기주 (전남대학교 기계시스템공학부)
  • Received : 2010.05.13
  • Accepted : 2010.06.17
  • Published : 2010.09.01

Abstract

In the hot section of a gas turbine, the turbine blades were protected from high temperature by providing a thermal barrier coating (TBC) as well as by cooling air flowing through internal passages within the blades. The cooling air then passed through discrete holes on the blade surface, creating a film of cooling air that further protects the surface from the hot mainstream flow. The holes are subjected to stresses resulting from the lateral growth of thermally grown oxide, the thermal expansion misfit between the constituent layers, and the centrifugal force due to high-speed revolution; these stresses often result in cracking. In this study, the deformation and cracks occurring near a hole on a heat-resistant alloy subjected to thermo-mechanical cycling were investigated. The experiment showed that cracks formed around the hole depending on the applied stress level and the number of cycles. These results could be explained by our analytic solution.

가스터빈엔진 내의 블레이드에서는 표면에 외부의 찬 공기를 흘려주는 작은 냉각 홀들을 가공하고 열 차단 코팅시스템을 코팅하는 방법으로 기지금속을 고온에서 보호한다. 열 차단 코팅은 열피로 과정에서 산화막의 성장 및 접합층과 산화막의 열팽창계수의 불일치로 산화막내부에 잔류응력이 발생하며 궁극적으로 코팅층의 분리를 유발한다. 본 연구에서는 내열합금 시편 표면에 작은 홀을 가공하여 여러 가지 고온 유지 조건에서 열 및 기계적 피로 시험을 수행하여 홀 주위의 산화막의 변형을 관찰하였다. 실험결과 기계적 피로가 홀 주위의 산화막의 변형에 중요한 영향을 미치며, 동일한 산화막 두께에서 고온 유지 시간이 짧을수록 변형이 쉽게 발생 하였다. 또한 본 연구에서는 홀 주위 산화막의 응력해석을 위한 이론적인 연구도 시도되었다.

Keywords

References

  1. Evans, A. G., He, M. Y. and Hutchinson, J. W., 2001, "Mechanics-Based Scaling Laws for the Durability of Thermal Barrier Coatings," Prog. Mat. Sci., Vol. 46, pp. 249-271. https://doi.org/10.1016/S0079-6425(00)00007-4
  2. Tolpygo, V. K. and Clarke, D. R., 1999, "Tensile Cracking During Thermal Cycling of Alumina Films Formed by High-Temperature Oxidation," Acta Mater, Vol. 47, No. 13, pp. 3589-3605. https://doi.org/10.1016/S1359-6454(99)00216-5
  3. Tolpygo, V. K. and Clarke ,D. R., 1999, "Alumina Scale Failure Resulting from Stress Relaxation" Surface and Coatings Technology, Vol. 120-121, pp. 1-7. https://doi.org/10.1016/S0257-8972(99)00331-X
  4. Tolpygo, V. K. and Clarke, D. R., 1998, "Wrinkling $\alpha$-Alumina Films Grown by Thermal Oxidation-I. Quantitative Studies on Single Crystals of Fe-Cr-Al Alloy," Acta Mater, Vol. 46, No. 14, pp. 5153-5166. https://doi.org/10.1016/S1359-6454(98)00133-5
  5. Tolpygo, V. K. and Clarke, D. R., 1998, "Wrinkling $\alpha$-Alumina Films Grown by Thermal Oxidation-II. Oxide Separation and Failure," Acta Mater, Vol. 46, No. 14, pp. 5167-5177. https://doi.org/10.1016/S1359-6454(98)00134-7
  6. Lee, S. S., Sun, S. K. and Kang, K. J., 2005, "In-Situ Measurement of the Thickness of Aluminum Oxide Scales at High Temperature," Oxidation of Metals, Vol.63, No. 1/2, pp. 73-85. https://doi.org/10.1007/s11085-005-1952-5
  7. Ko, G. D., Lee, S. S. and Kang, K. J., 2007, "Design and Manufacture of Creep Tester of Thin Film Form Specimen at High Temperature" Korean Society of Mechanical Engineers, Vol. A-31, pp. 253-259
  8. Ko, G. D, Sun, S. K. and Kang, K. J., 2007, "Creep & Tensile Properties of Thermally Grown Alumina Films," Korean Society of Mechanical Engineers, Vol. A-31, pp. 665-670. https://doi.org/10.3795/KSME-A.2007.31.6.665
  9. Karlsson, A. M., Hutchinson, J. W., Evans, A. G., 2002 "A fundamental model of cyclic instabilities in thermal barrier systems," Journal of the Mechanics and Physics of Solids Vol. 50, pp. 1565-1589. https://doi.org/10.1016/S0022-5096(02)00003-0
  10. Karlsson, A. M., Hutchinson, J. W., Evans, A. G., 2003, "The Displacement of the Thermally upon Temperature Cycling," Materials Science and Engineering, Vol. A351, pp. 244-257. https://doi.org/10.1016/S0921-5093(02)00843-2
  11. Sun, S. K., 2005, "On the Behavior of Thermally Grown Oxide Created upon a Heat-Resistant Metal," Ph. D. thesis, Chonnam National University.
  12. Saada, A. S., 1974, "Elasticity Theory and Applications," Pergamon Press Inc, pp. 323-329
  13. Ko, G. D., 2007, "Thermally Grown Oxides formed on Superalloy surfaces and their Mechanical Properties at High Temperature," Master Thesis. 2007, Chonnam National University.
  14. www.matweb.com
  15. Ding, Jun., Li, F. X., Kang, K. J., 2009, "Effects of Material Creep on Displacement Instability in Surface Groove under Thermo-Mechanical Cycling," Surface & coatings technology, Vol. 204, pp. 157-164. https://doi.org/10.1016/j.surfcoat.2009.07.007
  16. Ding, Jun., Li, F. X., Kang, K. J., 2009, "Numerical Simulation for TGO Crack Propagation near a surface groove in an Alumina Forming Alloy upon Thermo- Mechanical loading Cycles," Spring conference of KSME, Vol. 4, pp. 339-344.