한국전기전자재료학회논문지 (Journal of the Korean Institute of Electrical and Electronic Material Engineers)

  • 제23권6호
  • /
  • Pages.458-463
  • /
  • 2010
  • /
  • 1226-7945(pISSN)
  • /
  • 2288-3258(eISSN)
한국전기전자재료학회 (The Korean Institute of Electrical and Electronic Material Engineers)
권호 표지
DOI QR코드

DOI QR Code

Outgas 분석을 통한 MLCC Bar 변형률 측정

Experimental Study on the Deformation of MLCC Compressed Bar by Quantitative Analysis for Outgas

  • 김민주 (삼성전기(주) 부산연구분소) ;
  • 김종윤 (삼성전기(주) 부산연구분소) ;
  • 정기호 (삼성전기(주) 부산연구분소) ;
  • 박창식 (삼성전기(주) 부산연구분소)
  • Kim, Min-Ju (Busan R&D Center, Samsung Eelctro-Mechanics Co. LTD.) ;
  • Kim, Jong-Yun (Busan R&D Center, Samsung Eelctro-Mechanics Co. LTD.) ;
  • Jeong, Gi-Ho (Busan R&D Center, Samsung Eelctro-Mechanics Co. LTD.) ;
  • Park, Chang-Sik (Busan R&D Center, Samsung Eelctro-Mechanics Co. LTD.)
  • 투고 : 2010.03.03
  • 심사 : 2010.05.23
  • 발행 : 2010.06.01
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

MLCC (multi-layer ceramic capacitor) is usually fabricated by lamination of predetermined number of single layers. Often, the state of MLCC before sintering is called the green state, whose strength comes from the adhesion between the dielectric material and the polymer binder. Therefore the lamination of a single layer before sintering can be easily deformed by environment due to the relatively lower strength. After the compression process, which helps single sheets cohereto with adjacent sheets, the MLCC green bar is preheated to resolve the probable internal stress. Unfortunately, unexpected deformation after preheating resulted in problems during cutting of the MLCC green bar. In this study, one of 2 primary hypotheses which were proposed to resolve the unexpected deformation after preheating was examined by quantitative experiment with GC/MS (gas chromatograpy/mass spectrometer). The proportion of deformation caused by DOP evaporation, which was primarily evaporated componet during preheating, to the total deformation of the MLCC green bar was found to be 53%.

키워드

참고문헌

  1. G. Y. Onoda, Jr. and L. L. Hench, Ceramic Processing before Firing (Wiley-Interscience Publication, New York, 1978).
  2. S.-G. Lee, K.-S. Yook, and C.-H. Kim, J. Kor. Soc. Anal. Sci. 4, 169 (1991).
  3. A. L. Chuck, S. M. Turner, and P. S. Liss, Science297, 1151 (2002). https://doi.org/10.1126/science.1073896
  4. O. Chun, B. Suh, and J. Lee, Kor. J. Env. Hlth. Soc.20, 53 (1994).
  5. W. Callister, Materials Science and Engineering (Wiley, Toronto, Ontario, Canada, 1994), p. 430.
  6. S. Middleman, An Introduction to Mass and Heat Transfer (Wiley, New York, USA, 1998), p. 3.
  7. M. Tsige and G. S. Grest, J. Phys.: Condens. Matter.17, S4119 (2005). https://doi.org/10.1088/0953-8984/17/49/008
  8. R. E. Mistler and E. R. Twiname, Tape Casting: Theory and Practice (The American Ceramic Society, Columnbus, OH, 2000), p. 152.
  9. S. H. Lee, Minitab, Analysis of Measurement System (Eretec, Gunpo, yeonggi, Korea, 2006), p. 25.
  10. I. G. Currie, Fundamental Mechanics of Fluids(McGraw-Hill Inc., New York, USA, 1993)
  11. O. H. No, Basics of Viscous Fluid Mecahnics(Pakyoungsa, Seoul, Korea, 1996), p. 33.
  12. N. G. Mccrum, Principles of polymer engineering(Oxford University Press, New York, USA, 1997)