Smart Structures and Systems

  • 제6권7호
  • /
  • Pages.767-792
  • /
  • 2010
  • /
  • 1738-1584(pISSN)
  • /
  • 1738-1991(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Semi-analytical solutions for optimal distributions of sensors and actuators in smart structure vibration control

  • Jin, Zhanli (School of Electrical and Electronics Engineering, Nanyang Technological University(NTU)) ;
  • Yang, Yaowen (School of Civil and Environmental Engineering, Nanyang Technological University(NTU)) ;
  • Soh, Chee Kiong (School of Civil and Environmental Engineering, Nanyang Technological University(NTU))
  • 투고 : 2008.08.27
  • 심사 : 2009.10.08
  • 발행 : 2010.09.25
⟨ 이전 논문 다음 논문 ⟩

초록

In this paper, the optimal design of vibration control system for smart structures has been investigated semi-analytically via the optimization of geometric parameters like the placements and sizes of piezoelectric sensors and actuators (S/As) bonded on the structures. The criterion based on the maximization of energy dissipation was adopted for the optimization of the control system. Based on the sensing and actuating equations, the total energy stored in the system which is used as the objective function was analytically derived with design variables explicitly presented. Two cases of single and combined vibration modes were addressed for a simply supported beam and a simply supported cylindrical shell. For single vibration mode, the optimal distributions of the piezoelectric S/As could be obtained analytically. However, the Sequential Quadratic Programming (SQP) method has to be employed to solve those which violated the prescribed constraints and to solve the case of combined vibration modes. The results of three examples, which include a simply supported beam, a simply supported cylindrical shell and a simply supported plate, showed good agreement with those obtained by the Genetic Algorithm (GA) method. Moreover, in comparison with the GA method, the proposed method is more effective in obtaining better optimization results and is much more efficient in terms of computation time.

키워드

참고문헌

  1. Arockiasamy, M., Neelakanta, P.S. and Sreenivasan, G. (1992), "Vibration control of beams with embedded smart composite material", J. Aerospace Eng., 5(4), 492-498. https://doi.org/10.1061/(ASCE)0893-1321(1992)5:4(492)
  2. Bailey, T. and Hubbard, Jr. J.E. (1985), "Distributed piezoelectric-polymer active vibration control of a cantilever beam", J. Guid. Control Dynam., 8(5), 605-611. https://doi.org/10.2514/3.20029
  3. Baz, A. and Poh, S. (1988), "Performance of an active control system with piezoelectric actuators", J. Sound Vib., 126(2), 327-343. https://doi.org/10.1016/0022-460X(88)90245-3
  4. Bruant, I., Coffignal, G., Lene, F. and Verge, M. (2001), "A methodology for determination of piezoelectric actuator and sensor location on beam structures", J. Sound Vib., 243(5), 861-882. https://doi.org/10.1006/jsvi.2000.3448
  5. Chandrashekhara, K. and Agarwal, A.N. (1993), "Active vibration control of laminated composite plates using piezoelectric devices: a finite element approach", J. Intel. Mat. Syst. Str., 4(4), 496-508. https://doi.org/10.1177/1045389X9300400409
  6. Crawley, E.F. and de Luis, J. (1987), "Use of piezoelectric actuators as elements of intelligent structures", AIAA J., 25(10), 1373-1385. https://doi.org/10.2514/3.9792
  7. Devasia, S., Meressi, T., Paden, B. and Bayo, E. (1993), "Piezoelectric actuator design for vibration suppression: placement and sizing", J. Guid. Control Dynam., 16(5), 859-864. https://doi.org/10.2514/3.21093
  8. Jin, Z.L., Yang, Y.W. and Soh, C.K. (2005), "Application of fuzzy GA for optimal vibration control of smart cylindrical shells", Smart Mater. Struct., 14(6), 1250-1264. https://doi.org/10.1088/0964-1726/14/6/018
  9. Kalaycioglu, S., Giray, M. and Asmer, H. (1998), "Vibration control of flexible manipulators using smart structures", J. Aerospace Eng., 11(3), 90-94. https://doi.org/10.1061/(ASCE)0893-1321(1998)11:3(90)
  10. Kondoh, S., Yatomi, C. and Inoue, K. (1990), "The positioning of sensors and actuators in the vibration control of flexible systems", JSME Int. J., 33(2), 145-152.
  11. Krishnakumar, K. and Goldberg, D.E. (1992), "Control system optimization using genetic algorithms", J. Guid. Control Dynam., 15(3), 735-740. https://doi.org/10.2514/3.20898
  12. Lee, A.C. and Chen, S.T. (1994), "Collocated sensor/actuator positioning and feedback design in the control of flexible structure system", J. Vib. Acoust., 116(2), 146-154. https://doi.org/10.1115/1.2930405
  13. Lee, I. and Han, J.H. (1996), "Optimal placement of piezoelectric actuators in intelligent structures using genetic algorithms", Proceedings of the 3rd International Conference on Intelligent Materials and 3rd European Conference on Smart Structures and Materials, Lyon, France, June.
  14. Qing, G., Qiu, J. and Liu, Y. (2006), "A semi-analytical solution for static and dynamic analysis of plates with piezoelectric patches", Int. J. Solids Struct., 43(6), 1388-1403. https://doi.org/10.1016/j.ijsolstr.2005.03.048
  15. Sadri, A.M., Wright, J.R. and Wynne, R.J. (1999), "Modelling and optimal placement of piezoelectric actuators in isotropic plates using genetic algorithms", Smart Mater. Struct., 8(4), 490-498. https://doi.org/10.1088/0964-1726/8/4/306
  16. Udwadia, F.E. (1994), "Methodology for optimum sensor locations for parameter identification in dynamic systems", J. Eng. Mech.-ASCE, 120(2), 368-390. https://doi.org/10.1061/(ASCE)0733-9399(1994)120:2(368)
  17. Varadan, V.V., Kim, J. and Varadan, V.K. (1997), "Optimal placement of piezoelectric actuators for active noise control", AIAA J., 35(3), 526-533. https://doi.org/10.2514/2.126
  18. Wang, Q. and Quek, S.T. (2002), "A model for the analysis of beams with embedded piezoelectric layers", J. Intel. Mat. Syst. Str., 13(1), 61-70. https://doi.org/10.1177/1045389X02013001979
  19. Yang, Y.W., Jin, Z.L. and Soh, C.K. (2005), "Integrated optimal design of vibration control system for smart beams using genetic algorithms", J. Sound Vib., 282(3-5), 1293-1307. https://doi.org/10.1016/j.jsv.2004.03.048
  20. Yang, Y.W., Jin, Z.L. and Soh, C.K. (2006), "Integrated optimization of control system for smart cylindrical shells using modified GA", J. Aerospace Eng., 19(2), 68-79. https://doi.org/10.1061/(ASCE)0893-1321(2006)19:2(68)
  21. Yang, Y.W., Ju, C.K. and Soh, C.K. (2003), "Analytical and semi-analytical solutions for vibration control of a cantilevered column using a piezoelectric actuator", Smart Mater. Struct., 12(2), 193-203. https://doi.org/10.1088/0964-1726/12/2/306
  22. Zhang, H.W., Lennox, B., Goulding, P.R. and Leung, A.Y.T. (2000), "A float-encoded genetic algorithm technique for integrated optimization of piezoelectric actuator and sensor placement and feedback gains", Smart Mater. Struct., 9, 552-557. https://doi.org/10.1088/0964-1726/9/4/319

피인용 문헌

  1. Stochastic optimal control analysis of a piezoelectric shell subjected to stochastic boundary perturbations vol.9, pp.3, 2012, https://doi.org/10.12989/sss.2012.9.3.231
  2. Active vibration control of smart composite structures in hygrothermal environment vol.44, pp.2, 2010, https://doi.org/10.12989/sem.2012.44.2.127