Smart Structures and Systems

  • 제6권5_6호
  • /
  • Pages.689-709
  • /
  • 2010
  • /
  • 1738-1584(pISSN)
  • /
  • 1738-1991(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Development of a low-cost multifunctional wireless impedance sensor node

  • Min, Jiyoung (Department of Civil and Environmental Engineering, KAIST) ;
  • Park, Seunghee (Department of Civil and Environmental Engineering, Sungkyunkwan University) ;
  • Yun, Chung-Bang (Department of Civil and Environmental Engineering, KAIST) ;
  • Song, Byunghun (RFID-USN Convergence Research Center, Korea Electronics Technology Institute)
  • 투고 : 2009.11.12
  • 심사 : 2010.02.20
  • 발행 : 2010.07.25
⟨ 이전 논문 다음 논문 ⟩

초록

In this paper, a low cost, low power but multifunctional wireless sensor node is presented for the impedance-based SHM using piezoelectric sensors. Firstly, a miniaturized impedance measuring chip device is utilized for low cost and low power structural excitation/sensing. Then, structural damage detection/sensor self-diagnosis algorithms are embedded on the on-board microcontroller. This sensor node uses the power harvested from the solar energy to measure and analyze the impedance data. Simultaneously it monitors temperature on the structure near the piezoelectric sensor and battery power consumption. The wireless sensor node is based on the TinyOS platform for operation, and users can take MATLAB$^{(R)}$ interface for the control of the sensor node through serial communication. In order to validate the performance of this multifunctional wireless impedance sensor node, a series of experimental studies have been carried out for detecting loose bolts and crack damages on lab-scale steel structural members as well as on real steel bridge and building structures. It has been found that the proposed sensor nodes can be effectively used for local wireless health monitoring of structural components and for constructing a low-cost and multifunctional SHM system as "place and forget" wireless sensors.

키워드

참고문헌

  1. Bhalla, S., Naidu, A.S.K. and Soh, C.K. (2002), "Influence of structure-actuator interactions and temperature on piezoelectric mechatronic signatures for NDE", Proceedings of the ISSS-SPIE International Conferences on Smart Materials Structures and Systems, Bangalore, December.
  2. Giurgiutiu, V., Reynolds, A. and Rogers, C.A. (1999), "Experimental investigation of E/M impedance health monitoring of spot-welded structure joints", J. Intel. Mat. Syst. Str., 10, 802812. https://doi.org/10.1106/N0J5-6UJ2-WlGV-Q8MC
  3. Giurgiutiu, V., Zagrai, A.N. and Bao, J.J. (2002), "Piezoelectric wafer embedded active sensors for aging aircraft structural health monitoring", J. Struct. Health Monit., 1, 41-61. https://doi.org/10.1177/147592170200100104
  4. Giurgiutiu, V. (2008), Structural health monitoring with piezoelectric wafer active sensors, Amsterdam: Elsevier/Academic Press.
  5. Grisso, B.L. and Inman, D.J. (2005), "Developing an autonomous on-orbit impedance-based SHM system for thermal protection systems", Proceedings of the 5th Int'l Workshop on Structural Health Monitoring, Stanford, CA, September.
  6. Koo, K.Y., Park, S., Lee, J.J. and Yun, C.B. (2009), "Automated impedance-based structural health monitoring incorporating effective frequency shift for compensating temperature effects", J. Intel. Mat. Syst. Str., 20, 367-377. https://doi.org/10.1177/1045389X08088664
  7. Liang, C., Sun, F.P. and Rogers, C.A. (1996), "Electro-mechanical impedance modeling of active material systems", Smart Mater. Struct., 5, 171-186. https://doi.org/10.1088/0964-1726/5/2/006
  8. Lynch, J.P., Sundararajan, A., Law, K.H., Sohn, H. and Farrar, C.R. (2004), "Design of a wireless active sensing unit for structural health monitoring", Proceedings of the SPIE Annual Int'l Symposium on Smart Structures and Materials, San Diego, CA, March.
  9. Mascarenas, D.L., Todd, M.D., Park, G. and Farrar, C.R. (2007), "Development of an impedance-based wireless sensor node for structural health monitoring", Smart Mater. Struct., 16, 21372145. https://doi.org/10.1088/0964-1726/16/6/016
  10. Mascarenas, D.L., Park, G., Farinholt, K., Todd, M.D. and Farrar, C.R. (2009), "A low-power wireless sensing device for remote inspection of bolted joints", Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering, 223(5), 565-575. https://doi.org/10.1243/09544100JAERO378
  11. Overly, T.G., Park, G., Farrar, C.R. and Allemang, R.J. (2007), "Compact hardware development for structural health monitoring and sensor diagnostics using admittance measurements", Proceedings of the IMAC-XXV: A Conference & Exposition on Structural Dynamics, Orlando, FL, February.
  12. Overly, T.G., Park, G., Farinholt, K.M. and Farrar, C.R. (2008), "Development of an extremely compact impedance-based wireless sensing device", Smart Mater. Struct., 17(6).
  13. Park, G., Kabeya, K., Cudney, H.H. and Inman, D.J. (1999), "Impedance-based structural health monitoring for temperature varying applications", JSME Int. J. A-Solid M., 42, 249-258. https://doi.org/10.1299/jsmea.42.249
  14. Park, G., Sohn, H., Farrar, C.R. and Inman, D.J. (2003), "Overview of piezoelectric impedance-based health monitoring and path forward", Shock Vib. Digest, 35, 451-463. https://doi.org/10.1177/05831024030356001
  15. Park, G., Farrar, C.R., Rutherford, A.C. and Robertson, A.N. (2006), "Piezoelectric active sensor self-diagnostics using electrical admittance measurements", J. Vib. Acoust., 128, 469-476. https://doi.org/10.1115/1.2202157
  16. Park, S., Yun, C.B., Roh, Y. and Lee, J.J. (2005), "Health monitoring of steel structures using impedance of thickness modes at PZT patches", Smart Struct. Syst., 1, 339-353. https://doi.org/10.12989/sss.2005.1.4.339
  17. Park, S., Shin, H.H. and Yun, C.B. (2009a), "Wireless impedance sensor nodes for functions of structural damage identification and sensor self-diagnosis", Smart Mater. Struct., 18, 1-11.
  18. Park, S., Park, G., Yun, C.B. and Farrar, C.R. (2009b), "Sensor self-diagnosis using a modified impedance model for active sensing-based structural health monitoring", J. Struct. Health Monit., 8(1), 71-82. https://doi.org/10.1177/1475921708094792
  19. Peairs, D.M., Tarazaga, P.A. and Inman, D.J. (2006), "A study of the correlation between PZT and MFC resonance peaks and damage detection frequency intervals using the impedance method", Proceedings of the International Conference on Noise and Vibration Engineering, Leuven, Belgium, September.
  20. Saint-Pierre, N., Jayet, Y., Perrissin-Fabert, I. and Baboux, J.C. (1996), "The influence of bonding defects on the electric impedance of piezoelectric embedded element", J. Phys. D. Appl. Phys., 29, 2976-2982. https://doi.org/10.1088/0022-3727/29/12/006
  21. Taylor, S.G., Farinholt, K.M., Park, G. and Farrar, C.R. (2009a), "Wireless impedance device for electromechanical impedance sensing and low-frequency vibration data acquisition", Proceedings of the SPIE Annual International Symposium on Sensors and Smart Structures Technologies for Civil, Mechanical, and Aerospace Systems, San Diego, CA, March.
  22. Talyor, S.G., Farinholt, K.M., Flynn, E.B., Figueiredo, E., Mascarenas, D.L., Moro, E.A., Park, G., Todd, M.D. and Farrar, C.R. (2009b), "A mobile-agent-based wireless sensing network for structural monitoring applications", Meas. Sci. Technol., 20(4).

피인용 문헌

  1. Investigation of a new experimental method for damage assessment of RC beams failing in shear using piezoelectric transducers vol.114, 2016, https://doi.org/10.1016/j.engstruct.2016.02.014
  2. Recent R&D activities on structural health monitoring in Korea vol.3, pp.1, 2016, https://doi.org/10.12989/smm.2016.3.1.091
  3. Field Implementation of Wireless Vibration Sensing System for Monitoring of Harbor Caisson Breakwaters vol.8, pp.12, 2012, https://doi.org/10.1155/2012/597546
  4. A Recent Research Summary on Smart Sensors for Structural Health Monitoring vol.19, pp.3, 2015, https://doi.org/10.11112/jksmi.2015.19.3.010
  5. Electromechanical impedance of piezoelectric transducers for monitoring metallic and non-metallic structures: A review of wired, wireless and energy-harvesting methods vol.24, pp.9, 2013, https://doi.org/10.1177/1045389X13481254
  6. Real-time strength development monitoring for concrete structures using wired and wireless electro-mechanical impedance techniques vol.17, pp.6, 2013, https://doi.org/10.1007/s12205-013-0390-1
  7. Laser based impedance measurement for pipe corrosion and bolt-loosening detection vol.15, pp.1, 2015, https://doi.org/10.12989/sss.2015.15.1.041
  8. Smart sensing, monitoring, and damage detection for civil infrastructures vol.15, pp.1, 2011, https://doi.org/10.1007/s12205-011-0001-y
  9. Active-sensing platform for structural health monitoring: Development and deployment vol.15, pp.4, 2016, https://doi.org/10.1177/1475921716642171
  10. Impedance-based Long-term Structural Health Monitoring for Tidal Current Power Plant Structure in Noisy Environments vol.25, pp.4, 2011, https://doi.org/10.5574/KSOE.2011.25.4.059
  11. Damage classification of pipelines under water flow operation using multi-mode actuated sensing technology vol.20, pp.11, 2011, https://doi.org/10.1088/0964-1726/20/11/115002
  12. Impedance-based structural health monitoring using neural networks for autonomous frequency range selection vol.19, pp.12, 2010, https://doi.org/10.1088/0964-1726/19/12/125011
  13. Electromechanical impedance-based long-term SHM for jacket-type tidal current power plant structure vol.15, pp.2, 2015, https://doi.org/10.12989/sss.2015.15.2.283
  14. Impedance-based damage monitoring of steel column connection: numerical simulation vol.1, pp.3, 2014, https://doi.org/10.12989/smm.2014.1.3.339
  15. An electromechanical impedance-based method for tensile force estimation and damage diagnosis of post-tensioning systems vol.17, pp.1, 2016, https://doi.org/10.12989/sss.2016.17.1.107
  16. Applications of smart piezoelectric materials in a wireless admittance monitoring system (WiAMS) to Structures—Tests in RC elements vol.5, 2016, https://doi.org/10.1016/j.cscm.2016.03.003
  17. Impedance-based wireless debonding condition monitoring of CFRP laminated concrete structures vol.44, pp.2, 2011, https://doi.org/10.1016/j.ndteint.2010.10.006
  18. Impedance-based structural health monitoring incorporating neural network technique for identification of damage type and severity vol.39, 2012, https://doi.org/10.1016/j.engstruct.2012.01.012
  19. Smart wireless sensing and assessment for civil infrastructure vol.10, pp.4, 2014, https://doi.org/10.1080/15732479.2013.769011
  20. Monolithic Composite “Pressure + Acceleration + Temperature + Infrared” Sensor Using a Versatile Single-Sided “SiN/Poly-Si/Al” Process-Module vol.13, pp.12, 2013, https://doi.org/10.3390/s130101085
  21. A Review of the Piezoelectric Electromechanical Impedance Based Structural Health Monitoring Technique for Engineering Structures vol.18, pp.5, 2018, https://doi.org/10.3390/s18051307
  22. 온도 및 하중 영향을 고려한 임피던스 기반 조류발전용 재킷 구조물의 장기 건전성 모니터링 vol.31, pp.a5, 2010, https://doi.org/10.12652/ksce.2011.31.5a.351
  23. Advances and challenges in impedance-based structural health monitoring vol.4, pp.4, 2010, https://doi.org/10.12989/smm.2017.4.4.301
  24. Local Strand-Breakage Detection in Multi-Strand Anchorage System Using an Impedance-Based Stress Monitoring Method—Feasibility Study vol.19, pp.5, 2010, https://doi.org/10.3390/s19051054
  25. Bayesian forecasting approach for structure response prediction and load effect separation of a revolving auditorium vol.24, pp.4, 2010, https://doi.org/10.12989/sss.2019.24.4.507