마이크로전자및패키징학회지 (Journal of the Microelectronics and Packaging Society)

  • 제17권3호
  • /
  • Pages.17-26
  • /
  • 2010
  • /
  • 1226-9360(pISSN)
  • /
  • 2287-7525(eISSN)
한국마이크로전자및패키징학회 (The Korean Microelectronics and Packaging Society)
권호 표지

무아레 간섭계를 이용한 유연 솔더와 무연 솔더 실장 WB-PBGA 패키지의 열-기계적 변형 거동

Thermo-mechanical Behavior of WB-PBGA Packages with Pb-Sn Solder and Lead-free Solder Using Moire Interferometry

  • Lee, Bong-Hee (Department of Mechanical Engineering, Chungbuk National University) ;
  • Kim, Man-Ki (Department of Mechanical Engineering, Chungbuk National University) ;
  • Joo, Jin-Won (Department of Mechanical Engineering, Chungbuk National University)
  • 투고 : 2010.08.10
  • 심사 : 2010.08.30
  • 발행 : 2010.09.30
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

반도체 패키지에 사용되고 있는 유연 솔더는 환경 보호 필요성 대문에 무연 솔더로 빠르게 대체되고 있다. 이와 같은 무연 솔더에 대한 여구는 주로 재료의 발견과 공정 적응성의 관점에서 이루어졌을 뿐, 기계적인 성질이나 신뢰성의 관점에서의 연구는 많이 이루어지지 않았다. 본 논문에서는 무아레 간섭계를 이용하여 유연 솔더와 무연 솔더 실장 WB-PBGA 패키지 결합체의 온도변화에 대한 열-기게적 거동을 해석하였다. 실시간 무아레 간섭계를 이용하여 각 온도 단계에서 변위 분포를 나타내는 간섭무늬를 얻고, 그로부터 유연과 무연의 솔더 조인트를 갖는 WB-PBGA 패키지의 굽힘 변형 거동 및 솔더 볼의 변형률을 비교 분석하였다. 분석결과를 보면 유연 솔더 실장 패키지 결합체의 솔더 볼은 칩경계 부근인 #3 솔더 볼에서 발생하는 전단변형률이 파손에 큰 영향을 미치며, 무연 솔더가 실장된 패키지 결합체의 솔더 볼은 가장 바깥 부근인 #7 솔더 볼에서 발행하는 수직 변형률이 파손에 큰 영향을 미칠 것으로 예측된다, 또한 무연 솔더 실장 패키지 결합체는 같은 온도 조건에서 유연 솔더 실장된 패키지에 비해 굽힘 변형이 휠씬 크게 발생될 뿐 아니라 솔더 볼의 유효변형률도 10% 정도 크게 발생하는 것으로 나타나서 열변형에 의한 파손에 취약할 것으로 예측된다.

Pb-Sn solder is rapidly being replaced by lead-free solder for board-level interconnection in microelectronic package assemblies due to the environmental protection requirement. There is a general lack of mechanical reliability information available on the lead-free solder. In this study, thermo-mechanical behaviors of wire-bond plastic ball grid array (WB-PBGA) package assemblies are characterized by high-sensitivity moire interferometry. Experiments are conducted for two types of WB-PBGA packages that have Pb-Sn solder and lead-free solder as joint interconnections. Using real-time moire setup, fringe patterns are recorded and analyzed for several temperatures. Bending deformations of the assemblies and average strains of the solder balls are investigated and compared for the two type of WB-PBGA package assemblies. Results show that shear strain in #3 solder ball located near the chip shadow boundary is dominant for the failure of the package with Pb-Sn solder, while normal strain in #7 most outer solder ball is dominant for that with lead-free solder. It is also shown that the package with lead-free solder has much larger bending deformation and 10% larger maximum effective strain than the package with Pb-Sn solder at same temperature level.

키워드

과제정보

연구 과제 주관 기관 : 한국연구재단

참고문헌

  1. C. T. Peng, K. N. Chiang, T. Ku and K. Chang, "Design, Fabrication and Comparison of Lead-free/Eutectic Solder Joint Reliability of Flip Chip Package", Proc. 5th Int. Conf. on Thermal and Mechanical Simulation and Experimental in Micro-electronics and Micro-System, EuroSimE2004, 149 (2004).
  2. I. N. Jang, J. H. Park and Y. S. Ahn, "Mechanical Characteristic Evaluation of Sn-Ag-Cu Lead Free Solder Ball Joint on the Pad Geometry", J. Microelectron. Packag. Soc., 17(2), 41 (2010).
  3. I. Kim, T. Park and S.-B. Lee, "Comparative study of the Fatigue Behavior of SnAgCu and SnPb Solder Joits", Trans. of the KSME(A), 28(12), 1856 (2004).
  4. J. W. Joo and N. J. Choi, "The Effect of Finite Element Models in Thermal Analysis of Electronic Packages", Trans. of the KSME(A), 33(4), 380 (2009). https://doi.org/10.3795/KSME-A.2009.33.4.380
  5. B. Han, "Recent Advancements of Moire and Microscopic MoireInterferometry for Thermal Deformation Analysis of Microelectronics Devices", Experimental Mechanics, 38(4), 278 (1998).
  6. Y. Morita, K. Arakawa and M. Todo, "High-Sensitivity Measurement of Thermal Deformation in Stacked Multichip Package", IEEE Trans. Comp. Packag. Manufact. Technol., 30(1), 137 (2007). https://doi.org/10.1109/TCAPT.2007.892093
  7. S. M. Cho. S. Y. Cho and B. Han, "Observing Real-Time Thermal Deformations in Electronic Packaging", Experimental Techniques, Vol. 26(3), 25 (2002). https://doi.org/10.1111/j.1747-1567.2002.tb00065.x
  8. S. J. Ham and S. B. Lee, "Measurement of Creep and Relaxation Behaviors of Wafer-level CSP Assembly Using Moire Interferometry", J. Electronic Packaging, Trans. of the ASME, 125 (June), 282 (2003). https://doi.org/10.1115/1.1571571
  9. J. W. Joo, S. Cho and B. Han, "Characterization of Flexural and Thermo-mechanical Behavior of Plastic Ball Grid Array Package Assembly Using Moire Interferometry", Micrelectronics Reliability, 45(4), 637 (2005). https://doi.org/10.1016/j.microrel.2004.10.006
  10. D. Post, B. Han and P. Ifju, High Sensitivity Moire : Excremental Analysis for Mechanics and Materials, Springer-Verlag, New York (1994).
  11. TopLine 2010 Catalog from http://www.topline.tv (2010).
  12. J. W. Joo and D. H. Kim, "Thermo-mechanical Deformation Analysis of Flip Chip PBGA Packages subjected to Temperature Change", J. Microelectron. Packag. Soc., 13(4), 17 (2006).
  13. MatWeb Material Property Data from http://www.Matweb.com (2010).
  14. J. Joo and B. Han, "Non-linear Temperature Dependent Deformation Anaysis of CBGA Package Assembly Using Moire Interferometry", J. Microelectron. Packag. Soc., 10(4), 17 (2003).