대한금속재료학회지 (Korean Journal of Metals and Materials)

  • 제47권3호
  • /
  • Pages.195-201
  • /
  • 2009
  • /
  • 1738-8228(pISSN)
  • /
  • 2288-8241(eISSN)
대한금속재료학회 (The Korean Institute of Metals and Materials)
권호 표지

일렉트로 가스 용접부의 기계적 성질에 미치는 Mn 및 입열량의 영향

Effects of Mn and Heat-input on the Mechanical Properties of EGW Welds

  • 김남인 (한진중공업 기술연구소) ;
  • 정상훈 (한진중공업 기술연구소) ;
  • 이정수 (한진중공업 기술연구소) ;
  • 강성원 (부산대학교 조선해양공학과) ;
  • 김명현 (부산대학교 조선해양공학과)
  • Kim, Nam In (Technical Research Institute, Hanjin Heavy Industries & Construction Co., Ltd.) ;
  • Jeong, Sang Hoon (Technical Research Institute, Hanjin Heavy Industries & Construction Co., Ltd.) ;
  • Lee, Jeong Soo (Technical Research Institute, Hanjin Heavy Industries & Construction Co., Ltd.) ;
  • Kang, Sung Won (Department of Naval Architecture & Ocean Engineering, Pusan National University) ;
  • Kim, Myung Hyun (Department of Naval Architecture & Ocean Engineering, Pusan National University)
  • 투고 : 2008.09.02
  • 발행 : 2009.03.25
⟨ 이전 논문 다음 논문 ⟩

초록

This paper is concerned with effects of Mn and heat-input on the mechanical properties of EGW welds. Four different kinds of welding consumables were fabricated by varying Mn contents such as 1.3, 1.5, 1.7, 2.0%Mn and each consumable was welded for EGW on four heat-input conditions between 190 and 340 KJ/Cm. Mn contents were decreased as heat-input increases and alloy elements (C, Si, Ti, B, Al) to deoxidize easily also revealed similar tendency to Mn. Their microstructure, Charpy impact property and strength were investigated, and it is found that Charpy impact property and strength exhibit a strong dependence on change of microstructure by Mn contents and heat-input. The increase of Mn contents or the decrease of heat-input made the microstructure fine and increase volume fraction of acicular ferrite, thereby leading to the great improvement of Charpy impact property and strength. In case of single EGW, optimum Mn contents are over 1.7% for the toughness and strength.

키워드

참고문헌

  1. J. H. Koh and J. H. Kook, Journal of KWJS 11, 57 (1993)
  2. S. Lathabai and R. D. Stout, Welding Journal 58, 303 (1987)
  3. H. K. D. H. Bhadeshia, L.-E. Svensson, and B. Gretoft, Acta Metall. 33, 11271 (1985) https://doi.org/10.1016/0001-6160(85)90238-X
  4. Z. Zahng and R. A. Farrar, Welding Journal, May, 183s (1997)
  5. C. W. Yang, C. S. Kang, S. H. Hwang, and K. J. Kim, Journal of KWJS 8, 27 (1990)
  6. G. M. Evans, Welding Journal, March, 67s (1980)
  7. Y. M. Kim, S. Y. Shin, H. C. Lee, B. C. Hwang, B. G. Park, S. H. Lee, and N. J. Kim, J. Kor. Inst. Met. & Mater. 44, 223 (2006)
  8. G. M. Evans, Welding Journal, August, 249s (1995)
  9. K. Suenaga, Y. Matsushita, Y. Okazaki, and N. Hara, Kobe Steel Engineering Reports 54, 38 (2004)
  10. A. A. B. Sugden and H. K. D. H. Bhadeshia, Metall. Trans. 20A, 1811 (1989)
  11. K. S. Bang and W. S. Chang, Journal of KWJS 16, 93 (1998)
  12. H. J. Kim and B. Y. Kang, Journal of KWJS 18, 565 (2000)