Journal of Power Electronics

  • 제9권5호
  • /
  • Pages.748-756
  • /
  • 2009
  • /
  • 1598-2092(pISSN)
  • /
  • 2093-4718(eISSN)
전력전자학회 (The Korean Institute of Power Electronics)
권호 표지

Compensation of Position Error due to Amplitude Imbalance in Resolver Signals

  • Hwang, Seon-Hwan (Department of Electrical Engineering, Pusan National University) ;
  • Kwon, Young-Hwa (Department of Research and Development, Samsung Thales) ;
  • Kim, Jang-Mok (Department of Electrical Engineering, Pusan National University) ;
  • Oh, Jin-Seok (Division of Mechatronics Engineering, Korea Maritime University)
  • 발행 : 2009.09.20
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

This paper presents a compensation algorithm for position error due to an amplitude imbalance between resolver output signals. Resolvers are typically used to obtain absolute position information for motor drive systems in severe environments. Position error is caused by an amplitude imbalance of the resolver output signals. As a result, the d- and q-axis currents of synchronous reference frame have periodic ripples in the stator fundamental frequency in permanent magnet synchronous motor (PMSM) drive systems. Therefore, this paper proposes a compensation algorithm to reduce the position error generated by the amplitude imbalance. The proposed method does not require any additional hardware, and reduces computation time with a simple integral operation according to rotor position. In addition, the position error can be directly compensated for by the estimated position error. The effectiveness of the proposed compensation algorithm is verified through several simulations and experiments.

키워드

참고문헌

  1. Liu, G., Kunia, A., Larminat De, R., Desmond, P., and O'Gorman, T., "A low torque ripple PMSM drive for EPS applications," in Proc. IEEE APEC'04, pp.1130-1136, 2004
  2. A. Murray, B. Hare, A. Hirao, "Resolver position sensing system with integrated fault detection for automotive applications," in Proc. IEEE Sensors, Vol. 2, pp. 864-869, June. 2002 https://doi.org/10.1109/ICSENS.2002.1037221
  3. C. Attainaese, G. Tomasso, "Position measurement in industrial drives by means of low-cost resolver-to-digital converter," IEEE Trans. Instrum. Meas., Vol. 56, No. 6, pp. 2155-2159, Dec. 2007 https://doi.org/10.1109/TIM.2007.908120
  4. C.-H. Yim, I.-J. Ha, and M.-S. Ko, "A resolver-to-digital conversion method for fast tracking," IEEE Trans. Ind. Electron., Vol. 39, No. 5, pp. 369-378, Oct. 1992 https://doi.org/10.1109/41.161468
  5. M. Benammar, L. Ben-Brahim, and M.A Alhamadi, "A high precision resolver-to-DC converter," IEEE Trans. Instrum. Meas., Vol. 54, No. 6, pp. 2289-2296, Dec. 2005 https://doi.org/10.1109/TIM.2005.858135
  6. Hanselman, D.C, "Resolver signal requirements for high accuracy resolver-to-digital conversion," IEEE Trans. Ind. Electron., Vol. 37, pp. 556-561, Dec. 1990 https://doi.org/10.1109/41.103461
  7. Mok, H.S., Kim, S.H., Cho, Y.H. "Reduction of PMSM torque ripple caused by resolver position error," Electronics Letters, Vol. 43, No.11, pp. 646-647, 2007 https://doi.org/10.1049/el:20070296
  8. Tamagawa Seiki Co., "TS2223N13E102 Datasheet," 2005