Heat Transfer and Pressure Drop Characteristics in Zigzag Channel Angles of Printed Circuit Heat Exchangers

지그재그채널 PCHE의 각도에 따른 열전달 및 압력강하특성

  • 권오경 (한국생산기술연구원 에너지설비기술지원센터) ;
  • 최미진 (한국생산기술연구원 에너지설비기술지원센터) ;
  • 최영종 ((주)이노월)
  • Published : 2009.09.10

Abstract

The objectives of this paper are to study the characteristics of heat transfer and pressure drop of the zigzag channel PCHE using diffusion bonding technology by numerical analysis. PCHE of five types are designed, which are zigzag channel angle 180$^{\circ}$, 160$^{\circ}$, 140$^{\circ}$, 120$^{\circ}$ and 100$^{\circ}$. The zigzag PCHE was numerically investigated for Reynolds number in a range of 150$\sim$800. The temperatures of the hot side were performed at 80$^{\circ}$ while that of the cold side was conducted at 20$^{\circ}C$. The results show that the performance of heat transfer rate for zigzag channel 100$^{\circ}$ increases about 11.5% compared to that of zigzag channel 180$^{\circ}$. On the other hand, the performance of pressure drop for zigzag channel 100$^{\circ}$ is remarkably higher than that of zigzag channel 180$^{\circ}$, about 2.4 times.

Keywords

References

  1. Pua, L. M. and Rumbold, S. O., 2003, Industrial microchannel devices-where are we today?, First International Conference on Microchannels and Minichannels, pp. 773-780
  2. Nikitin, K., Kato, Y. and Ngo, L., 2006, Printed circuit heat exchanger thermal-hydraulic performance in supercritical CO2 experimental loop, International Journal of Refrigeration, Vol. 29, No. 5, pp. 807-814 https://doi.org/10.1016/j.ijrefrig.2005.11.005
  3. Ngo, L., Kato, Y., Nikitin, K. and Tsuzuki, N., 2006, New printed circuit heat exchanger with S-shaped fins for hot water supplier, Experimental Thermal and Fluid Science, Vol. 30, No. 8, pp. 811-819 https://doi.org/10.1016/j.expthermflusci.2006.03.010
  4. Tsuzuki, N., Kato, Y. and Ishiduka, T., 2007, High performance printed circuit heat exchanger, Applied Thermal Engineering, Vol. 27, No. 10, pp. 1702-1707 https://doi.org/10.1016/j.applthermaleng.2006.07.007
  5. Ngo, L., Kato, Y., Nikitin, K. and Ishizuka, T., 2007, Heat transfer and pressure drop correlations of microchannel heat exchangers with s-shaped and zigzag fins for carbon dioxide cycles, Experimental Thermal and Fluid Science, Vol. 32, pp. 560-570 https://doi.org/10.1016/j.expthermflusci.2007.06.006
  6. Kim, Y. H., Moon, J. E., Choi, Y. J. and Lee, K. J., 2008, Heat transfer characteristics and pressure drop in straight microchannel of the printed circuit heat exchangers, Transaction of the KSME, Vol. 32, No. 12, pp. 915-923 https://doi.org/10.3795/KSME-B.2008.32.12.915
  7. Kim, D. E., Kim, M. H., Cha, J. E. and Kim, S. O., 2008, Numerical investigation on thermal-hydraulic performance of new printed circuit heat exchanger model, Nuclear Engineering and Design, Vol. 238, No. 12, pp. 3269-3276 https://doi.org/10.1016/j.nucengdes.2008.08.002
  8. Kwon, O. K., Cha, D. A. and Yun, J. H., 2009, An experimental study on the performance of diffusion bonding heat exchangers, Transaction of the KSME, Vol. 33, No. 1, pp. 53-59 https://doi.org/10.3795/KSME-B.2009.33.1.53
  9. Pra, F., Tochon, P., Mauget, C., Fokkens, J. and Willemsen, S., 2008, Promising designs of compact heat exchangers for modular HTRs using the brayton cycle, Nuclear Engineering and Design, Vol. 238, pp. 3160-3173 https://doi.org/10.1016/j.nucengdes.2007.12.024
  10. Hwang, S. D., Jang, I. H. and Cho, H. H., 2006, Experimental study on flow and local heat/mass transfer characteristics inside corrugated duct, International Journal of Heat and Fluid Flow, Vol. 27, pp. 21-32 https://doi.org/10.1016/j.ijheatfluidflow.2005.07.001