DOI QR코드

DOI QR Code

Free vibration of axially loaded Reddy-Bickford beam on elastic soil using the differential transform method

  • Yesilce, Yusuf (Dokuz Eylul University, Civil Engineering Department, Engineering Faculty) ;
  • Catal, Seval (Dokuz Eylul University, Civil Engineering Department, Engineering Faculty)
  • 투고 : 2008.12.09
  • 심사 : 2009.01.19
  • 발행 : 2009.03.10

초록

The literature regarding the free vibration analysis of Bernoulli-Euler and Timoshenko beams on elastic soil is plenty, but the free vibration analysis of Reddy-Bickford beams on elastic soil with/without axial force effect using the Differential Transform Method (DTM) has not been investigated by any of the studies in open literature so far. In this study, the free vibration analysis of axially loaded Reddy-Bickford beam on elastic soil is carried out by using DTM. The model has six degrees of freedom at the two ends, one transverse displacement and two rotations, and the end forces are a shear force and two end moments in this study. The governing differential equations of motion of the rectangular beam in free vibration are derived using Hamilton's principle and considering rotatory inertia. Parameters for the relative stiffness, stiffness ratio and nondimensionalized multiplication factor for the axial compressive force are incorporated into the equations of motion in order to investigate their effects on the natural frequencies. At first, the terms are found directly from the analytical solutions of the differential equations that describe the deformations of the cross-section according to the high-order theory. After the analytical solution, an efficient and easy mathematical technique called DTM is used to solve the governing differential equations of the motion. The calculated natural frequencies of one end fixed and the other end simply supported Reddy-Bickford beam on elastic soil using DTM are tabulated in several tables and figures and are compared with the results of the analytical solution where a very good agreement is observed and the mode shapes are presented in graphs.

키워드

참고문헌

  1. Ayaz, F. (2004), "Application of differential transforms method to differential-algebraic equations", Appl. Math. Comput., 152, 648-657
  2. Bert, C.W. and Zeng, H. (2004), "Analysis of axial vibration of compound bars by differential transformation method", J. Sound Vib., 275, 641-647 https://doi.org/10.1016/j.jsv.2003.06.019
  3. Bickford, W.B. (1982), "A consistent higher order beam theory", Development Theor. Appl. Mech., 11, 137-15
  4. Bildik, N., Konuralp, A., Bek, F.O. and Küçükarslan, S. (2006), "Solution of different type of the partial differential equation by differential transform method and Adomian's decomposition method", Appl. Math. Comput., 172, 551-567 https://doi.org/10.1016/j.amc.2005.02.037
  5. Çatal, S. (2006), "Analysis of free vibration of beam on elastic soil using differential transform method", Struct. Eng. Mech., 24(1), 51-62 https://doi.org/10.12989/sem.2006.24.1.051
  6. Çatal, S. (2008), "Solution of free vibration equations of beam on elastic soil by using differential transform method", Appl. Math. Model., 32, 1744-1757 https://doi.org/10.1016/j.apm.2007.06.010
  7. Çatal, S. and Çatal, H.H. (2006), "Buckling analysis of partially embedded pile in elastic soil using differential transform method", Struct. Eng. Mech., 24(2), 247-268 https://doi.org/10.12989/sem.2006.24.2.247
  8. Chen, C.K. and Ho, S.H. (1996), "Application of differential transformation to eigenvalue problem", J. Appl. Math. Comput., 79, 173-188 https://doi.org/10.1016/0096-3003(95)00253-7
  9. Chen, C.K. and Ho, S.H. (1999), "Transverse vibration of a rotating twisted Timoshenko beams under axial loading using differential transform", Int. J. Mech. Sci., 41, 1339-1356 https://doi.org/10.1016/S0020-7403(98)00095-2
  10. Chen, C.L. and Liu, Y.C. (1998), “Solution of two-point boundary-value problems using the differential transformation method”, J. Optimiz. Theory App., 99, 23-35 https://doi.org/10.1023/A:1021791909142
  11. Cowper, G.R. (1966), "The shear coefficient in Timoshenko's beam theory", J. Appl. Mech., 33(2), 335-340 https://doi.org/10.1115/1.3625046
  12. Doyle, P.F. and Pavlovic, M.N. (1982), "Vibration of beams on partial elastic foundations", J. Earthq. Eng.Struct. Dyn., 10, 663-674 https://doi.org/10.1002/eqe.4290100504
  13. Ertürk, V.S. (2007), "Application of differential transformation method to linear sixth-order boundary value problems", Appl. Math. Sci., 1, 51-58
  14. Ertürk, V.S. and Momani, S. (2007), "Comparing numerical methods for solving fourth-order boundary value problems", Appl. Math. Comput., 188, 1963-1968 https://doi.org/10.1016/j.amc.2006.11.075
  15. Esmailzadeh, E. and Ohadi, A.R. (2000), "Vibration and stability analysis of non-uniform Timoshenko beams under axial and distributed tangential loads", J. Sound Vib., 236, 443-456 https://doi.org/10.1006/jsvi.2000.2999
  16. Gruttmann, F. and Wagner, W. (2001), "Shear coefficient factors in Timoshenko's beam theory for arbitrary shaped cross-section", Comput. Mech., 27, 199-207 https://doi.org/10.1007/s004660100239
  17. Han, S.M., Benaroya, H. and Wei, T. (1999), "Dynamics of transversely vibrating beams using four engineering theories", J. Sound Vib., 225, 935-988 https://doi.org/10.1006/jsvi.1999.2257
  18. Hassan, I.H.A.H (2002a), "On solving some eigenvalue problems by using differential transformation", Appl.Math. Comput., 127, 1-22 https://doi.org/10.1016/S0096-3003(00)00123-5
  19. Hassan, I.H.A.H (2002b), "Different applications for the differential transformation in the differential equations",Appl. Math. Comput., 129, 183-201 https://doi.org/10.1016/S0096-3003(01)00037-6
  20. Hetenyi, M. (1955), Beams on Elastic Foundations, 7th edn., The University of Michigan Press, Michigan
  21. Heyliger, P.R. and Reddy, J.N. (1988), "A higher-order beam finite element for bending and vibration problems",J. Sound Vib., 126(2), 309-326 https://doi.org/10.1016/0022-460X(88)90244-1
  22. Ho, S.H. and Chen, C.K. (2006), "Free transverse vibration of an axially loaded non-uniform sinning twisted Timoshenko beam using differential transform", Int. J. Mech. Sci., 48, 1323-1331 https://doi.org/10.1016/j.ijmecsci.2006.05.002
  23. Jang, M.J. and Chen, C.L. (1997), "Analysis of the response of a strongly non-linear damped system using a differential transformation technique", Appl. Math. Comput., 88, 137-151 https://doi.org/10.1016/S0096-3003(96)00308-6
  24. Jang, M.J., Chen, C.L. and Liu, Y.C. (2000), "On solving the initial-value problems using differential transformation method", Appl. Math. Comput., 115, 145-160 https://doi.org/10.1016/S0096-3003(99)00137-X
  25. Kaya, M.O. and Ozgumus, O.O. (2007), "Flexural-torsional-coupled vibration analysis of axially loaded closedsection composite Timoshenko beam by using DTM", J. Sound Vib., 306, 495-506 https://doi.org/10.1016/j.jsv.2007.05.049
  26. Kurnaz, A., Oturanç, G. and Kiris, M.E. (2005), "n-Dimensional differential transformation method for solving PDEs", Int. J. Comput. Math., 82(3), 369-380 https://doi.org/10.1080/0020716042000301725
  27. Levinson, M. (1981), "A new rectangular beam theory", J. Sound Vib., 74, 81-87 https://doi.org/10.1016/0022-460X(81)90493-4
  28. Malik, M. and Dang, H.H. (1998), "Vibration analysis of continuous systems by differential transformation", Appl. Math. Comput., 96, 17-26 https://doi.org/10.1016/S0096-3003(97)10076-5
  29. Murthy, A.V. (1970), "Vibration of short beams", AIAA, 8, 34-38 https://doi.org/10.2514/3.5602
  30. Özdemir, Ö. and Kaya, M.O. (2006), "Flapwise bending vibration analysis of a rotating tapered cantilever Bernoulli-Euler beam by differential transform method", J. Sound Vib., 289, 413-420 https://doi.org/10.1016/j.jsv.2005.01.055
  31. Ozgumus, O.O. and Kaya, M.O. (2006), "Flapwise bending vibration analysis of double tapered rotating Euler- Bernoulli beam by using the differential transform method", Meccanica, 41, 661-670 https://doi.org/10.1007/s11012-006-9012-z
  32. Ozgumus, O.O. and Kaya, M.O. (2007), "Energy expressions and free vibration analysis of a rotating double tapered Timoshenko beam featuring bending-torsion coupling", Int. J. Eng. Sci., 45, 562-586 https://doi.org/10.1016/j.ijengsci.2007.04.005
  33. Rajasekaran, S. (2008), "Buckling of fully and partially embedded non-prismatic columns using differential quadrature and differential transformation methods", Struct. Eng. Mech., 28(2), 221-238 https://doi.org/10.12989/sem.2008.28.2.221
  34. Reddy, J.N. (2002), Energy Principles and Variational Methods in Applied Mechanics, Second Edition, JohnWiley, NY
  35. Reddy, J.N. (2007), Theory and Analysis of Elastic Plates and Shells, Second Edition, Taylor & Francis;Philadelphia, PA
  36. Timoshenko, S.P. (1921), "On the correction for shear of the differential equation for transverse vibrations ofprismatic bars", Philos. Mag., 41, 744-746
  37. Wang, C.M., Reddy, J.N. and Lee, K.H. (2000), Shear Deformable Beams and Plates: Relationships with Classical Solutions, Elsevier Science Ltd., The Netherlands
  38. West, H.H. and Mafi, M. (1984), "Eigenvalues for beam columns on elastic supports", J. Struct. Eng., 110(6),1305-1320 https://doi.org/10.1061/(ASCE)0733-9445(1984)110:6(1305)
  39. Yesilce, Y. and Catal, H.H. (2008), "Free vibration of semi-rigid connected Reddy-Bickford piles embedded in elastic soil", Sadhana-Academy Proceedings in Engineering Science, 33(6), 781-801
  40. Yokoyama, T. (1991), "Vibrations of Timoshenko beam-columns on two parameter elastic foundations", Earthq. Eng. Struct. Dyn., 20, 355-370 https://doi.org/10.1002/eqe.4290200405
  41. Zhou, J.K. (1986), Differential Transformation and Its Applications for Electrical Circuits, Huazhong UniversityPress, Wuhan China

피인용 문헌

  1. A novel four variable refined plate theory for laminated composite plates vol.22, pp.4, 2016, https://doi.org/10.12989/scs.2016.22.4.713
  2. A new simple shear and normal deformations theory for functionally graded beams vol.18, pp.2, 2015, https://doi.org/10.12989/scs.2015.18.2.409
  3. Bending and free vibration of functionally graded beams using various higher-order shear deformation beam theories vol.62, pp.1, 2012, https://doi.org/10.1016/j.ijmecsci.2012.05.014
  4. Comparative dynamic analysis of axially loaded beams on modified Vlasov foundation vol.57, pp.6, 2016, https://doi.org/10.12989/sem.2016.57.6.969
  5. On bending, buckling and vibration responses of functionally graded carbon nanotube-reinforced composite beams vol.19, pp.5, 2015, https://doi.org/10.12989/scs.2015.19.5.1259
  6. Dynamic basic displacement functions for free vibration analysis of tapered beams vol.17, pp.14, 2011, https://doi.org/10.1177/1077546310396430
  7. Dynamic stiffness approach and differential transformation for free vibration analysis of a moving Reddy-Bickford beam vol.58, pp.5, 2016, https://doi.org/10.12989/sem.2016.58.5.847
  8. A new first shear deformation beam theory based on neutral surface position for functionally graded beams vol.15, pp.5, 2013, https://doi.org/10.12989/scs.2013.15.5.467
  9. Differential transform method and numerical assembly technique for free vibration analysis of the axial-loaded Timoshenko multiple-step beam carrying a number of intermediate lumped masses and rotary inertias vol.53, pp.3, 2015, https://doi.org/10.12989/sem.2015.53.3.537
  10. Lateral-Torsional Buckling of Nonuniformly Loaded Beam Using Differential Transformation Method vol.16, pp.07, 2016, https://doi.org/10.1142/S0219455415500340
  11. Differential transform method for free vibration analysis of a moving beam vol.35, pp.5, 2010, https://doi.org/10.12989/sem.2010.35.5.645
  12. Free vibration of an axially functionally graded pile with pinned ends embedded in Winkler-Pasternak elastic medium vol.40, pp.4, 2009, https://doi.org/10.12989/sem.2011.40.4.583
  13. Response of forced Euler-Bernoulli beams using differential transform method vol.42, pp.1, 2009, https://doi.org/10.12989/sem.2012.42.1.095
  14. A novel meshless particle method for nonlocal analysis of two-directional functionally graded nanobeams vol.41, pp.7, 2009, https://doi.org/10.1007/s40430-019-1799-3