References
- Goldstein, R. J., 1971, “Film Cooling,” Advances in Heat Transfer, Vol. 7, pp. 321-379. https://doi.org/10.1016/S0065-2717(08)70020-0
- Goldstein, R. J., Eckert, E. R. G., and Burggraf, f., 1974, “Effects of Hole Geometry and Density on Three-Dimensional Film Cooling,” Int. J. of Heat Mass Transfer, Vol. 17, pp. 595-607. https://doi.org/10.1016/0017-9310(74)90007-6
- Leylek, J. H. and Zerkle, R. D., 1994, “Discrete-jet Film Cooling: A Comparison of Computational Results withExperiments,” ASME J. of Turbomacinery, Vol. 116, No. 3, pp. 321-379.
- Schmidt, D. L., Sen, B., and Bogard D. G., 1994, “Film Cooling With Compound Angle Holes: Adiabatic Effectiveness,”ASME J. of Turbomacinery, Vol. 118, No. 4, pp. 807-813.
- Cho, H. H. and Goldstein, R. J., 1995, “Heat (Mass) Transfer and Film Cooling Effectiveness With Injection Through DiscreteHoles: Part I-Within Holes and on the Back Surface,” ASME J. of Turbomachinery, Vol. 117, No. 3, pp. 440-450. https://doi.org/10.1115/1.2835680
- Cho, H. H. and Goldstein, R. J., 1995, “Heat (Mass) Transfer and Film Cooling Effectiveness With Injection Through DiscreteHoles: Part II-On the Exposed Surface,” ASME J. of Turbomachinery, Vol. 117, No. 3, pp. 451-460. https://doi.org/10.1115/1.2835681
- Goldstein, R. J., Cho, H. H., and Jabbari, M. Y., 1997, "Effect of Plenum Crossflow on Heat (Mass) Transfer Near and Withinthe Entrance of Film Cooling Holes," ASME J. of Turbomachinery, Vol. 119, No. 4, pp. 761-769. https://doi.org/10.1115/1.2841186
- Cho H. H., Kang, S. G., and Rhee, D. H., 2001, “Heat/Mass Transfer Measurement Within a Film Cooling Hole of Square andRectangular Cross Section,” ASME J. of Turbomacinery, Vol. 123, No. 4, pp. 806-814. https://doi.org/10.1115/1.1400109
- Wan, E., Hong, C., Dewey, R., Bernstein, H., and Norsworthy, D., 2005, “Life Management System for Advanced F Class GasTurbine,” EPRI Report 1008319.
- Geidmann, J. D., Kassab, A. J., Divo, E. A, Rodriguez, F., and Steinthorsson, E., 2003, “Conjugate Heat Transfer Effects ona Realistic Film-Cooled Turbine Vane,” ASME Turbo Expo 2003, Atlanta, USA, Paper No. GT2003-38553.
- Nowak, G. and Wroblewski, W., 2007, “Thermo-mechanical Optimization of Cooled Turbine Vane,” ASME Turbo Expo2007, Montreal, Canada, Paper No. GT2007-28196.
- Tinga, T., Kampen, J. F., Jager, B, and Kok, J. B. W., 2007, “Gas Turbine Combustor Liner Life Assessment Using aCombined Fluid/Structural Approach,” ASME J. of Eng. for Gas Turbines and Power, Vol. 129, No. 1, pp. 69-79. https://doi.org/10.1115/1.2360603
Cited by
- Conjugated heat transfer and temperature distributions in a gas turbine combustion liner under base-load operation vol.24, pp.9, 2010, https://doi.org/10.1007/s12206-010-0625-8