Advanced Composite Materials

  • 제18권3호
  • /
  • Pages.221-232
  • /
  • 2009
  • /
  • 0924-3046(pISSN)
  • /
  • 1568-5519(eISSN)
한국복합재료학회 (The Korean Society for Composite Materials)
권호 표지
DOI QR코드

DOI QR Code

Influence of Allylamine Plasma Treatment Time on the Mechanical Properties of VGCF/Epoxy

  • Khuyen, Nguyen Quang (Composite Materials Laboratory, Korea Institute of Materials Science (KIMS)) ;
  • Kim, Jin-Bong (Composite Materials Laboratory, Korea Institute of Materials Science (KIMS)) ;
  • Kim, Byung-Sun (Composite Materials Laboratory, Korea Institute of Materials Science (KIMS)) ;
  • Lee, Soo (Department of Chemical Engineering, Changwon National University)
  • 투고 : 2008.04.23
  • 심사 : 2008.06.12
  • 발행 : 2009.09.01
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

The allylamine plasma treatment is used to modify the surface properties of vapor grown carbon fibers (VGCF). It is to improve the interfacial bonding between the VGCF and epoxy matrix. The allylamine plasma process was performed by batch process in a vacuum chamber, using gas injection followed by plasma discharge for the durations of 20, 40 and 60 min. The interdependence of mechanical properties on the VGCF contents, treatment time and interfacial bonding between VGCF/ep was investigated. The interfacial bonding between VGCF and epoxy matrix was observed by scanning electron microscopy (SEM) micrographs of nanocomposites fracture surfaces. The changes in the mechanical properties of VGCF/ep, such as the tensile modulus and strength were discussed. The mechanical properties of allylamine plasma treated (AAPT) VGCF/ep were compared with those of raw VGCF/ep. The tensile strength and modulus of allyamine plasma treated VGCF40 (40 min treatment)/ep demonstrated a higher value than those of other samples. The mechanical properties were increased with the allyamine plasma treatment due to the improved adhesion at VGCF/ep interface. The modification of the carbon nanofibers surface was observed by transmission electron microscopy (TEM). SEM micrographs showed an excellent dispersion of VGCF in epoxy matrix by ultrasonic method.

키워드

참고문헌

  1. J. Park, D. Kim, S. Kim, P. Kim, D. Yoon and K. DeVries, Inherent sensing and interfacial evaluation of carbon nanofiber and nanotube/ep composites using electrical resistance measurement and micromechanical technique, Composites Part B 30, 847–861 (2006)
  2. N. Chisholm, H. Mahfuz, V. Rangari, A. Ashfaq and S. Jeelani, Fabrication and mechanical characterization of carbon/SiC-epoxy nanocomposites, Compos. Struct. 67, 115–124 (2005)
  3. Y. Zhou, F. Pervin, S. Jeelani and P. Mallick, Improvement in mechanical properties of carbon fabric–epoxy composite using carbon nanofibers, Mater. Proc. Technol. 198, 445–453 (2008)
  4. J. Paredes, A. Alonso and J. Tasco'n, Oxygen plasma modification of submicron vapor grown carbon fibers as studied by scanning tunneling microscopy, Carbon 40, 1101–1108 (2002)
  5. J. Figueiredo, P. Serp, B. Nysten and J. Issi, Surface treatments of vapor-grown carbon fibers produced on a substrate: Part II: Atomic force microscopy, Carbon 37, 1809–1816 (1999)
  6. P. Serp, J. Figueiredo, P. Bertrand and J. Issi, Surface treatments of vapor-grown carbon fibers produced on a substrate, Carbon 36, 1791–1799 (1998)
  7. J. Kim, A. Sharma and Y. Lee, Demonstration of the formation of porous silicon films with superior mechanical properties, morphology and stability, Mater. Lett. 60, 1166–1169 (2006)
  8. J. Fidelus, E. Wiesel, F. Gojny, K. Schulte and H. Wagner, Thermo-mechanical properties of randomly oriented carbon/epoxy nanocomposites, Composites Part A 36, 1555–1561 (2005)
  9. Y. Iwahori, S. Ishiwata, T. Sumizawa and T. Ishikawa, Mechanical properties improvements in two-phase and three-phase composites using carbon nano-fiber dispersed resin, Composites Part A 36, 1430–1439 (2005)
  10. J. Xu, J. Donohoe and C. Pittman, Preparation, electrical and mechanical properties of vapor grown carbon fiber (VGCF)/vinyl ester composites, Composites Part A 35, 693–701 (2004)
  11. M. Inagaki, K. Kaneko and T. Nishizawa, Nanocarbons — recent research in Japan, Carbon 42, 1401–1417 (2004)
  12. S. Sihn, R. Kim, W. Huh, K. Lee and A. Roy, Improvement of damage resistance in laminated composites with electrospun nano-interlayers, Compos. Sci. Technol. 68, 673–683 (2008)
  13. V. Yudin, A. Feldman, V. Svetlichnyi, A. Shumakov and G. Marom, Crystallization of R-BAPB type polyimide modified by carbon nano-particles, Compos. Sci. Technol. 67, 789–794 (2007)
  14. B. Shim, J. Starkovich and N. Kotov, Multilayer composites from vapor-grown carbon nano-fibers, Compos. Sci. Technol. 66, 1174–1181 (2006)
  15. Y. Zhou, F. Pervin, V. Rangari and S. Jeelani, Fabrication and evaluation of carbon nano fiber filled carbon/epoxy composite, Mater. Sci. Engng A 426, 221–228 (2006)
  16. Y. Zhou, M. Baseer, H. Mahfuz and S. Jeelani, Monte Carlo simulation on tensile failure process of unidirectional carbon fiber reinforced nano-phased epoxy, Mater. Sci. Engng A 420, 63–71 (2006)
  17. F. Gojny, M. G. Wichmann, B. Fiedler, W. Bauhofer and K. Schulte, Influence of nanomodification on the mechanical and electrical properties of conventional fibre-reinforced composites, Composites Part A 36, 1525–1535 (2005)
  18. F. Pervin, Y. Zhou, V. Rangari and S. Jeelani, Testing and evaluation on the thermal and mechanical properties of carbon nano fiber reinforced SC-15 epoxy, Mater. Sci. Engng A 405, 246–253 (2005)
  19. T. Uchida, T. Dang, B. Min, X. Zhang and S. Kumar, Processing, structure, and properties of carbon nano fiber filled PBZT composite fiber, Composites Part B 36, 183–187 (2005)
  20. H. Lin, S. Shiue, Y. Chou, H. Lin and T. Wu, Effect of substrate temperature on the properties of carbon-coated optical fibers prepared by plasma enhanced chemical vapor deposition, Thin Solid Films 516, 114–118 (2007)
  21. H. Poche, J. Dijon and T. Monsabert, Radio-frequency plasma system to selectively grow vertical field-aligned carbon nanofibers from a solid carbon source, Carbon 45, 2904–2916 (2007)
  22. J. Zheng, X. Zhang, P. Li, X. Zhou, D. Chen, Y. Liu and W. Yuan, Oxygen reduction reaction properties of carbon nanofibers: effect of metal purification, Electrochim. Acta 53, 3587–3596 (2008)
  23. K. Yamaguchi, M. Kitazawa, Z.Wang, Y. Sugita, J. Tanaka, M. Tanemura and Y. Hayashi, Roomtemperature growth of ion-induced carbon nanofibers: effects of ion species, Diamond and Related Materials 17, 525–528 (2008)
  24. S. Lee, T. Kim, A. Ogale and M. Kim, Surface and structure modification of carbon nanofibers, Synthetic Metals 157, 644–650 (2007)
  25. S. Lee, S. Da, A. Ogale and M. Kim, Effect of heat treatment of carbon nanofibers on polypropylene nanocomposites, J. Phys. Chem. Solids 69, 1407–1410 (2008)
  26. H. Miyagawa and L. Drzal, Effect of oxygen plasma treatment on mechanical properties of vapor grown carbon fiber nanocomposites, Composites Part A 36, 1440–1448 (2005)
  27. V. Bruser, M. Heintze, W. Brandl, G. Marginean and H. Bubert, Surface modification of carbon nanofibres in low temperature plasmas, Diamond and Related Materials 13, 1177–1181 (2004)
  28. H. Bubert, X. Haiber, M. Heintze, V. Bruser, E. Pasch, W. Brandl and G. Marginean, Basic analytical investigation of plasma-chemically modified carbon fibers, Spectrochimica Acta Part B 57, 1601–1610 (2002)
  29. C. Jones and E. Sammann, The effect of low power plasmas on carbon fibre surfaces, Carbon 28, 509–514 (1990)
  30. B. Kim and S. Park, A simple method for the preparation of activated carbon fibers coated with graphite nanofibers, Interface Sci. 315, 791–794 (2007)
  31. A. Felten, C. Bittencourt, J. Colomer, G. Tendeloo and J. Pireaux, Nucleation of metal clusters on plasma treated multi wall carbon nanotubes, Carbon 45, 110–116 (2007)
  32. P. He, Y. Gao, J. Lian, L. Wang, D. Qian, J. Zhao, W. Wang, M. Schulz, X. Zhou and D. Shi, Surface modification and ultrasonication effect on the mechanical properties of carbon nanofiber/polycarbonate composites, Composites Part A 37, 1270–1275 (2006)
  33. H. Okuno, E. Grivei, F. Fabry, T. Gruenberger and J. Aguilar, Synthesis of carbon nanotubes and nano-necklaces by thermal plasma process, Carbon 42, 2543–2549 (2004)
  34. L. Burton, The thermooxidative stability of cured epoxy resins, J. Appl. Polym. Sci. 47, 1821–1837 (1993)
  35. E. Karayannidou, D. Achilias and I. Sideridou, Cure kinetics of epoxy–amine resins used in the restoration of works of art from glass or ceramic, Eur. Polym. J. 42, 3311–3323 (2006)
  36. J. Kim, D. Seong, T. Kang and J. Younm, Effects of surface modification on rheological and mechanical properties of CNT/epoxy composites, Carbon 44, 1898–1905 (2006)
  37. N. Lu, S. Tang, S. Ryu and H. Choi, Surface characterization of the activated carbon fibers after plasma polymerization of allylamine, Carbon Sci. 6, 243–247 (2005)