Smart Structures and Systems

Techno-Press (테크노프레스)
권호 표지
DOI QR코드

DOI QR Code

Detection of edge delamination in surface adhered active fiber composites

  • Wang, Dwo-Wen (Department of Mechanical Engineering, National Chiao Tung University) ;
  • Yin, Ching-Chung (Department of Mechanical Engineering, National Chiao Tung University)
  • Received : 2009.02.02
  • 심사 : 2009.05.13
  • 발행 : 2009.11.25
⟨ Previous Next ⟩

초록

A simple method has been developed to detect the bonding condition of active fiber composites (AFC) adhered to the surface of a host structure. Large deformation actuating capability is one of important features of AFC. Edge delamination in adhesive layer due to large interfacial shear stress at the free edge is typically resulted from axial strain mismatch between bonded materials. AFC patch possesses very good flexibility and toughness. When an AFC patch is partially delaminated from host structure, there remains sensing capability in the debonded part. The debonding size can be determined through axial resonance measured by the interdigitated electrodes symmetrically aligned on opposite surfaces of the patch. The electrical impedance and modal response of the AFC patch in part adhered to an aluminum plate were investigated in a broad frequency range. Debonding ratio of the AFC patch is in inverse proportion to the resonant frequency of the fundamental mode. Feasibility of in-situ detecting the progressive delamination between AFC patch and host plate is demonstrated.

키워드

과제정보

연구 과제 주관 기관 : National Science Council of the Republic of China

참고문헌

  1. ANSI/IEEE Std 176-1987, IEEE Standard on Piezoelectricity, IEEE, New York, NY.
  2. Bent, A.A., Hagood, N.W. and Rodgers, J.P. (1995), "Anisotropic actuation with piezoelectric fiber composites", J. Intel. Mat. Syst. Str., 6, 338-349. https://doi.org/10.1177/1045389X9500600305
  3. Bent, A.A. and Hagood, N.W. (1997), "Piezoelectric fiber composites with interdigitated electrodes", J. Intel. Mat. Syst. Str., 8, 903-919. https://doi.org/10.1177/1045389X9700801101
  4. Brunner, A.J., Barbezat, M., Flueler, P., Kornmann, X. and Huber, C. (2004), "Active fiber composites for application as acoustic emission sensors: principles and characterization", DGZfP Proc. BB 90-CD, Lecture, 54, 549-556.
  5. Brunner, A.J., Barbezat, M., Huber, C. and Flueler, P.H. (2005), "The potential of active fiber composites made from piezoelectric fibers for actuating and sensing applications in structural health monitoring", Mater. Struct., 38, 561-567. https://doi.org/10.1617/14314
  6. Cass, R.B., Khan, A. and Mohammadi, F. (2003), "Innovative ceramic-fiber technology energizes advanced cerametrics", Am. Ceram. Soc. Bull., 9701-9706.
  7. Datta, S., Kirikera, G.R., Schulz, M.J. and Sundaresan, M.J. (2003), "Continuous sensors for structural health monitoring", Proc. of SPIE, 5046, 164-175.
  8. Delale, F., Erodgan, F. and Aydinoglu, M.N. (1981), "Stresses in adhesively bonded joints: A close-form solution", J. Compos. Mater., 15, 249-271. https://doi.org/10.1177/002199838101500305
  9. Giurgiutiu, V., Zagrai, A. and Bao, J.H. (2002), "Piezoelectric wafer embedded active sensors for aging aircraft structural health monitoring", Struct. Health Monit., 1(1), 41-61. https://doi.org/10.1177/147592170200100104
  10. Melnykowycz, M., Kornmann, X., Huber, C., Barbezat, M. and Brunner, A.J. (2006), "Performance of integrated active fiber composites in fiber reinforced epoxy laminates", Smart Mater. Struct., 15, 204-212. https://doi.org/10.1088/0964-1726/15/1/050
  11. Park, G., Farrar, C.R., Rutherford, A.C. and Robertson, A.N. (2006), "Piezoelectric active sensor self-diagnostics using electrical admittance measurements", J. Vib. Acoust. ASME, 128(4), 469-476. https://doi.org/10.1115/1.2202157
  12. Schulz, M.J., Sundaresan, M.J., Ghoshal, A. and Pai, P.F. (2000), "Active fiber composites for structural health monitoring", Proc. of SPIE, 3992, 13-24.
  13. Seeley, C.E. and Chattopadhyay, A. (1998), "Experimental investigation of composite beams with piezoelectric actuation and debonding", Smart Mater. Struct., 7, 502-511. https://doi.org/10.1088/0964-1726/7/4/010
  14. Sodano, H.A., Park, G. and Inman, D.J. (2004), "An investigation into the performance of macro-fiber composites for sensing and structural vibration applications", Mech. Syst. Signal Pr., 18, 683-697. https://doi.org/10.1016/S0888-3270(03)00081-5
  15. Wang, K.P., Huang, Y.Y., Chandra, A. and Hu, K.X. (2000), "Interfacial shear stress, peeling stress, and die cracking stress in trilayer electronic assemblies", IEEE. T. Compon. Pack. T., 23, 309-316. https://doi.org/10.1109/6144.846769
  16. Wickramasinghe, V.K. and Hagood, N.W. (2004), "Material characterization of active fiber composites for integral twist-actuated rotor blade application", Smart Mater. Struct., 13, 1155-1165. https://doi.org/10.1088/0964-1726/13/5/020
  17. Wilkie, W.K., Bryant, R.G., High, J.W., Fox, R.L., Hellbaum, R.F., Jalink, A., Little, Jr., B.D. and Mirick, P.H. (2000), "Low-cost piezocomposite actuator for structural control applications", Proc. of 7th SPIE Int. Symposium on Smart Structures and Materials, Newport Beach, CA, March 5-9.

피인용 문헌

  1. Analysis of the machinability of GFRE composites in drilling processes vol.36, pp.4, 2009, https://doi.org/10.12989/scs.2020.36.4.417