대한기계학회논문집A (Transactions of the Korean Society of Mechanical Engineers A)

  • 제32권12호
  • /
  • Pages.1140-1145
  • /
  • 2008
  • /
  • 1226-4873(pISSN)
  • /
  • 2288-5226(eISSN)
대한기계학회 (The Korean Society of Mechanical Engineers)
권호 표지
DOI QR코드

DOI QR Code

열 수축 튜브 자동 절단 장치를 위한 공정제어 및 감시 시스템에 관한 연구

A Study on Manufacturing Process Control and Monitoring System for Heat-Shrink-Tube Cutting Machine

  • 김형석 (울산대학교 기계자동차공학과) ;
  • 이병룡 (울산대학교 기계자동차공학부) ;
  • 유호영 (울산과학대학 디지털기계학부)
  • 발행 : 2008.12.01
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

In conventional cutting system of Heat-Shrink-Tube, workers operate cutting system after considering about length and quantity of heat-shrink-tube. So, not only work time and production cost is increased but also material is wasted because the data that workers have to consider is so much. In this paper, an effective cutting system of heat-shrink-tube was developed to reduce production cost, work time and waste of material. The cutting system consists of a supervisory computer installed inside a control room, a on-site computer installed on the work area, and a PLC system. In the developed system, a supervisory computer send work order to the on-site computer using LAN and the on-site computer operates the cutting system of the heatshrink-tube after it makes an array production order. Also, the on-site computer reports information to the supervisory computer when an accident happened.

키워드

참고문헌

  1. Jung, T. S., Yang, M. Y. and Byun, C. W., 2003, “The Development of Distributed Tool Management System tailored for Injection Mold Production,” Trans. of the KSPE, Vol. 20, No. 4, pp. 118-127
  2. Piementel, J., 1990, “Communication Networks for Manufacturing”, Prentice Hall
  3. Ko, D. K. and Lee, S. G., 2000, “Remote Monitoring and Control of PLC using TCP/IP Communication,” Conf. of KSPE, pp. 140-143
  4. Kim, K. A. and Hong, S. H., 1998, “A Case Study on the Implementation and Performance Evaluation of Profibus Network in Automation Systems,” Trans. of Control∙Automation∙System Engineering, Vol. 4, No. 1, pp. 113-122
  5. Kim, H. M., 2003, “A Study on Fuzzy Temperature Control for the Barrels of Injection Molding Machine using PC based PLC,” Trans. of Control∙Automation∙ System Engineering, Vol. 9, No. 10, pp. 768-773 https://doi.org/10.5302/J.ICROS.2003.9.10.768
  6. Kim, J. W., 1990, “PLC and Factory Automation,” Trans. of Mechanical Science and Technology, Vol. 30, No. 1, pp. 17-21
  7. Zhang H., and et al., 1996, “On-line PLC Monitoring and Network Administering System for Steel Tube Mill,” Proc. of IEEE on Industrial Technology https://doi.org/10.1109/ICIT.1996.601689

피인용 문헌

  1. Design of Information Acquisition System for Equipments on Shop Floor vol.35, pp.1, 2011, https://doi.org/10.3795/KSME-A.2011.35.1.039