열처리공학회지 (Journal of the Korean Society for Heat Treatment)

  • 제21권3호
  • /
  • Pages.137-143
  • /
  • 2008
  • /
  • 1225-1070(pISSN)
  • /
  • 2508-4046(eISSN)
한국열처리공학회 (The Korean Society for Heat Treatment)
권호 표지

GCD 50의 ADI처리시 기계적 성질에 미치는 퀜칭 매질의 영향

Effect of Quenching Medium on the Mechanical Properties of ADI Treated GCD 50

  • 김한군 (부경대학교 신소재공학부) ;
  • 오이식 (부경대학교 신소재공학부) ;
  • 김헌주 (부경대학교 신소재공학부) ;
  • 신기근 (부경대학교 신소재공학부)
  • Kim, H.G. (Division of Advanced Material Science and Eng., Pukyong National university) ;
  • Oh, I.S. (Division of Advanced Material Science and Eng., Pukyong National university) ;
  • Kim, H.J. (Division of Advanced Material Science and Eng., Pukyong National university) ;
  • Shin, K.G. (Division of Advanced Material Science and Eng., Pukyong National university)
  • 투고 : 2008.03.21
  • 심사 : 2008.04.19
  • 발행 : 2008.05.31
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

Effect of quenching medium on the mechanical properties of ductil iron GCD 50 has been investigated using ADI treated specimens. The specimens have been austenitized at $900^{\circ}C$ for 2 hours, followed by controlled cooling to $800^{\circ}C$ under the cooling rate of $0.05^{\circ}C/sec$, then austempered at $380^{\circ}C$, $330^{\circ}C$, $280^{\circ}C$ and $230^{\circ}C$ for 1 hour. The specimens treated in the salt of 5% water were found to have higher tensile strength than that of the normal salt bath. Elongation and impact energy increased in proportion to the increase of retained austenite volume fraction. The increase of cooling rate of the salt by the addition of 5% water to the salt resulted in the increase of retained austenite volume fraction and the formation of fine bainitic ferrite.

키워드

참고문헌

  1. J. Zimba, M. Samandi, D. Yu, T. Chandra, E. Navara, and D. J. Simbi : Mater. Des. 25(5) (2004) 431 https://doi.org/10.1016/j.matdes.2003.11.004
  2. J. Yang and S. K. Putatunda : Materials and Design 25(3) (2004) 219 https://doi.org/10.1016/j.matdes.2003.09.021
  3. Yoshisada, Mitsuhara, Hiroyuki : IMONO 7(11) (1985) 46
  4. C. Ishigawa : Casting, Forging & Heat-treatment, (1980) 3
  5. F. S. Rossi and B. K. Gupta : Metal Progress 119(5) (1981) 25
  6. M. Johanson : AFS Trans., 85 (1977) 117
  7. Moore D. J., Rouns T. N. and Rundman K. B. : A processing window concept. AFS Trans., 94 (1986) 255
  8. M. Gagne : AFS Trans., 93 (1985) 801
  9. Takeshi Hiraoka, Hironobu Yamamoto : IMONO, 62 (1990) 543
  10. Mitsuo Niinomi, Hironobu Yamamoto : IMONO, 58 (1986) 287
  11. Toshimi Sasaki, K. Hoshino, K. Nakamura, and H. Sumimoto : IMONO 65(6) (1993) 491
  12. T.Y Chung : J. Kor. Soc. for Heat-treatment, 15 (2002) 3-8
  13. Kovacs B. V. : AFS Trans., 102 (1994) 417
  14. J. Yang and S. K. Putatunda : Materials and Design 25(3) (2004) 219 https://doi.org/10.1016/j.matdes.2003.09.021
  15. R. Elliott : Heat Treatment of Metals, 3 (1997) 55
  16. N. Darwish and R. Elliott : Materials Science and Technology, 9 (1993) 572 https://doi.org/10.1179/026708393790172286