Steel and Composite Structures

Techno-Press (테크노프레스)
권호 표지
DOI QR코드

DOI QR Code

Experimental study on flexural strength of reinforced modular composite profiled beams

  • Ahn, Hyung-Joon (Department of Architectural Engineering, Kon-Kuk University) ;
  • Ryu, Soo-Hyun (Department of Architectural Design, Sahm-Yook University)
  • Received : 2007.10.05
  • Accepted : 2008.06.01
  • Published : 2008.08.25
⟨ Previous Next ⟩

Abstract

This study attempts to suggest bending reinforcement method by applying bending reinforcement to composite profile beam in which the concept of prefabrication is introduced. Profile use can be in place of framework and is effective in improvement of shear and bending strength and advantageous in long-term deflection. As a result of experiment, MPB-CB2 with improved module had higher strength and ductility than the previously published MPB-CB and MPB-LB. In case of bending reinforcement with deformed bar and built-up T-shape section based on MPB-CB2, the MPB-RB series reinforced with deformed bar were found to have higher initial stiffness, bending strength and ductility than the MPB-RT series. The less reinforcement effect of the MPB-RT series might be caused by poor concrete filling at the bottom of the built-up T-shape. In comparison between theoretical values and experimental values using minimum yield strength, the ratio between experimental value and theoretical value was shown to be 0.9 or higher except for MPB-RB16 and MPB-RT16 that have more reinforcement compared to the section, thus it is deemed that the reinforced modular composite profiled beam is highly applicable on the basis of minimum yield strength.

Keywords

References

  1. Ahmed, M., Oehlers, D.J. and Bradford, M.A. (2000), "Retrofitting reinforced concrete beams by bolting steel plates to their sides. Part 1: Behavior and experiments", Struct. Eng. Mech., Int. J., 10(3), 211-226. https://doi.org/10.12989/sem.2000.10.3.211
  2. Brian Uy, and Andrew Bradford (1995), "Ductility of Profile Beams. Part : Experimental Study", ASCE J. Struct. Eng., 121(5), 876-882. https://doi.org/10.1061/(ASCE)0733-9445(1995)121:5(876)
  3. Brian Uy, and Andrew Bradford (1995), "Ductility of Profile Beams. Part : Analytical Study", ASCE J. Struct. Eng., 121(5), 883-889. https://doi.org/10.1061/(ASCE)0733-9445(1995)121:5(883)
  4. Hyung-Joon Ahn, Soo-Hyun Ryu (2007), "Experimental Study on Flexural Strength of Modular Composite Profile Beams" Steel Compo. Struct. An Int. J., 7(1), 71-85. https://doi.org/10.12989/scs.2007.7.1.071
  5. Minglan Peng and Zhifei Shi (2004), "Interface characteristics of RC beams strengthened with FRP plate" Struct. Eng. and Mech., An Int. J., 18(3), 315-330. https://doi.org/10.12989/sem.2004.18.3.315
  6. Oehlers D.J. (1993), "Composite Profile Beams" ASCE J. Struct. Eng., 119(4), 1085-1100. https://doi.org/10.1061/(ASCE)0733-9445(1993)119:4(1085)
  7. Oehlers D.J., Wright H.D. and Burnet M.J. (1994), "Flexural Strength of Profile Beams", ASCE J. Struct. Eng., 120(2), 378-393. https://doi.org/10.1061/(ASCE)0733-9445(1994)120:2(378)
  8. Oehlers, D.J., Ahmed, M., Nguyen N.T. and Bradford, M.A. (1997), "Transverse and Longitudinal partial interaction in composite bolted side-plated reinforced concrete beams", Struct. Eng. Mech., An Int. J., 5(5), 553-563. https://doi.org/10.12989/sem.1997.5.5.553
  9. Oehlers, D.J., Ninh T Nguyen and Bradford, M.A. (2000), "Retrofitting by adhesive bonding steel plates to sides of R.C. beams. Part 1: Debonding of plates due to flexure, Struct. Eng. Mech., An Int. J., 9(5), 491-503. https://doi.org/10.12989/sem.2000.9.5.491
  10. Oehlers, D.J., Ninh T Nguyen and Bradford, M.A. (2000), "Retrofitting by adhesive bonding steel plates to sides of R.C. beams. Part 2: Debonding of plates due to shear and design rules", Struct. Eng. Mech., An Int. J., 9(5), 505-518. https://doi.org/10.12989/sem.2000.9.5.505
  11. Oehlers, D.J., Ahmed, M., Nguyen N.T. and Bradford, M.A. (2000), "Retrofitting reinforced concrete beams by bolting steel plates to their sides. Part 2: Transverse interaction and rigid plastic design", Struct. Eng. Mech., An Int. J., 10(3), 227-243. https://doi.org/10.12989/sem.2000.10.3.227
  12. Sang Hun Kim and Riyad S. Aboutaha, (2004), "Ductility of carbon fiber-reinforced polymer (CFRP) strengthened reinforced concrete beams: Experimental investigation" Steel Compo. Struct. An Int. J., 4(5).

Cited by

  1. Study on behavior of T-section modular composite profiled beams vol.10, pp.5, 2008, https://doi.org/10.12989/scs.2010.10.5.457
  2. Investigation on the flexural behavior of an innovative U-shaped steel-concrete composite beam vol.34, pp.3, 2008, https://doi.org/10.12989/scs.2020.34.3.441