Structural Engineering and Mechanics

  • 제29권3호
  • /
  • Pages.259-278
  • /
  • 2008
  • /
  • 1225-4568(pISSN)
  • /
  • 1598-6217(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Seismic performance assessment of reinforced concrete bridge piers supported by laminated rubber bearings

  • Kim, T.H. (Civil Engineering Research Team, Daewoo Institute of Construction Technology) ;
  • Kim, Y.J. (Civil Engineering Research Team, Daewoo Institute of Construction Technology) ;
  • Shin, H.M. (Department of Civil and Environmental Engineering, Sungkyunkwan University)
  • 투고 : 2006.12.18
  • 심사 : 2008.03.31
  • 발행 : 2008.06.20
⟨ 이전 논문 다음 논문 ⟩

초록

This paper presents a nonlinear finite element procedure accounting for the effects of geometric as well as material nonlinearities for reinforced concrete bridge piers supported by laminated rubber bearings. Reinforced concrete bridge piers supported by laminated rubber bearings and carrying a cyclic load were analyzed by using a special purpose, nonlinear finite element program, RCAHEST. For reinforced concrete, the proposed robust nonlinear material model captures the salient response characteristics of the bridge piers under cyclic loading conditions and addresses with the influence of geometric nonlinearity on post-peak response of the bridge piers by transformations between local and global systems. Seismic isolator element to predict the behaviors of laminated rubber bearings is also developed. The seismic performance of reinforced concrete bridge piers supported by laminated rubber bearings is assessed analytically. The results show good correlation between the experimental findings and numerical predictions, and demonstrate the reliability and robustness of the proposed analytical model. Additionally, the studies and discussions presented in this investigation provide an insight into the key behavioral aspects of reinforced concrete bridge piers supported by laminated rubber bearings.

키워드

참고문헌

  1. Abe, M., Yoshida, J. and Fujino, Y. (2004), "Multiaxial behaviors of laminated rubber bearings and their modeling. II: Modeling", J. Struct. Eng., ASCE, 130(8), 1133-1144 https://doi.org/10.1061/(ASCE)0733-9445(2004)130:8(1133)
  2. American Association of State Highway and Transportation Officials (1999), AASHTO Guide Specifications for Seismic Isolation Design
  3. Bathe, K.J. (1996), Finite Element Procedures, Prentice-Hall, Inc.
  4. Chen, B.J., Tsai, C.S., Chung, L.L. and Chiang, T.C. (2006), "Seismic behavior of structures isolated with a hybrid system of rubber bearings", Struct. Eng. Mech., 22(6), 761-783 https://doi.org/10.12989/sem.2006.22.6.761
  5. Hwang, J.S., Wu, J.D., Pan, T.C. and Yang, G. (2002), "A mathematical hysteretic model for elastomeric isolation bearings", Earthq. Eng. Struct. Dyn., 31, 771-789 https://doi.org/10.1002/eqe.120
  6. Juhn, G., Manolis, G.D., Constantinou, M.C. and Reinhorn, A.M. (1992), "Experimental study of secondary systems in base-isolated structure", J. Struct. Eng., ASCE, 118(8), 2204-2221 https://doi.org/10.1061/(ASCE)0733-9445(1992)118:8(2204)
  7. Kakuta, Y., Okamura, H. and Kohno, M. (1982), "New concepts for concrete fatigue design procedures in Japan", IABSE Colloquium of Fatigue of Steel and Concrete Structures, Lausanne, 51-58
  8. Kato, B. (1979), "Mechanical properties of steel under load cycles idealizing seismic action", CEB Bulletin D'Information, 131, 7-27
  9. Kim, T.H., Kim, B.S., Chung, Y.S. and Shin, H.M. (2006), "Seismic performance assessment of reinforced concrete bridge piers with lap splices", Eng. Struct., 28(6), 935-945 https://doi.org/10.1016/j.engstruct.2005.10.020
  10. Kim, T.H., Lee, K.M., Chung, Y.S. and Shin, H.M. (2005), "Seismic damage assessment of reinforced concrete bridge columns", Eng. Struct., 27(4), 576-592 https://doi.org/10.1016/j.engstruct.2004.11.016
  11. Kim, T.H., Lee, K.M. and Shin, H.M. (2002), "Nonlinear analysis of reinforced concrete shells using layered elements with drilling degree of freedom", ACI Struct. J., 99(4), 418-426
  12. Kim, T.H., Lee, K.M., Yoon, C.Y. and Shin, H.M. (2003), "Inelastic behavior and ductility capacity of reinforced concrete bridge piers under earthquake. I: Theory and formulation", J. Struct. Eng., ASCE, 129(9), 1199-1207 https://doi.org/10.1061/(ASCE)0733-9445(2003)129:9(1199)
  13. Kim, T.H. and Shin, H.M. (2001), "Analytical approach to evaluate the inelastic behaviors of reinforced concrete structures under seismic loads", J. Earthq. Eng. Soc. Korea, EESK, 5(2), 113-124
  14. Li, B., Maekawa, K. and Okamura, H. (1989), "Contact density model for stress transfer across cracks in concrete", J. Faculty Eng., University of Tokyo (B), 40(1), 9-52
  15. Maekawa, K. and Okamura, H. (1983), "The deformational behavior and constitutive equation of concrete using elasto-plastic and fracture model", J. Faculty Eng., University of Tokyo (B), 37(2), 253-328
  16. Mander, J.B., Panthaki, F.D. and Kasalanati, K. (1994), "Low-cycle fatigue behavior of reinforcing steel", J. Mater. Civil Eng., ASCE, 6(4), 453-468 https://doi.org/10.1061/(ASCE)0899-1561(1994)6:4(453)
  17. Mander, J.B, Priestley, M.J.N. and Park, R. (1988), "Theoretical stress-strain model for confined concrete", J. Struct. Eng., ASCE, 114(8), 1804-1826 https://doi.org/10.1061/(ASCE)0733-9445(1988)114:8(1804)
  18. Naeim, F. and Kelly, J.M. (1999), Design of Seismic Isolated Structure from Theory to Practice, John willey & Sons, Inc.
  19. Okamura, H., Maekawa, K. and Izumo, J. (1987), "RC plate element subjected to cyclic loading", IABSE Colloquium, Delft, 54, 575-590
  20. Roeder, C.W. and Stanton, J.F. (1991), "State-of-the-art elastomeric bridge bearing design", ACI Struct. J., 88(1), 31-41
  21. Shima, H., Chou, L. and Okamura, H. (1987), "Micro and macro models for bond behavior in reinforced concrete", J. Faculty Eng., University of Tokyo (B), 39(2), 133-194
  22. Shoji, G., Kawashima, K. and Saito, A. (2001), "Cyclic loading test to clarify nonlinear behavior of an isolated bridge supported by high damping rubber bearings", J. Struct. Mech. Earthq. Eng., JSCE, 682(I-56), 81-100 (in Japanese)
  23. Skinner, R.I., Robinson, W.H. and McVerry, G.H. (1993), An Introduction to Seismic Isolation, John Wiley & Sons
  24. Taylor, R.L. (2000), FEAP - A Finite Element Analysis Program, version 7.2 users manual, Vols 1-2
  25. Yalcin, C. and Saatcioglu, M. (2000), "Inelastic analysis of reinforced concrete columns", Comput. Struct., 77(5), 539-555 https://doi.org/10.1016/S0045-7949(99)00228-X

피인용 문헌

  1. Design charts for yield acceleration and seismic displacement of retaining walls with surcharge through limit analysis vol.52, pp.6, 2014, https://doi.org/10.12989/sem.2014.52.6.1225
  2. Study on the Stiffness Correction Method of Novel Antivibration Bearing for Urban Rail Transit Viaduct vol.2017, 2017, https://doi.org/10.1155/2017/1402301
  3. Seismic Response of a Three-Dimensional Asymmetric Multi-Storey Reinforced Concrete Structure vol.8, pp.4, 2018, https://doi.org/10.3390/app8040479
  4. Minimum deformability design of high-strength concrete beams in non-seismic regions vol.8, pp.4, 2008, https://doi.org/10.12989/cac.2011.8.4.445
  5. Compression of hollow-circular fiber-reinforced rubber bearings vol.38, pp.3, 2011, https://doi.org/10.12989/sem.2011.38.3.361
  6. Inelastic design of high-axially loaded concrete columns in moderate seismicity regions vol.39, pp.4, 2008, https://doi.org/10.12989/sem.2011.39.4.559
  7. Concurrent flexural strength and deformability design of high-performance concrete beams vol.40, pp.4, 2008, https://doi.org/10.12989/sem.2011.40.4.541
  8. Prediction of seismic displacements in gravity retaining walls based on limit analysis approach vol.42, pp.2, 2008, https://doi.org/10.12989/sem.2012.42.2.247
  9. Investigation of the seismic performance of precast segmental tall bridge columns vol.43, pp.3, 2008, https://doi.org/10.12989/sem.2012.43.3.287