Structural Engineering and Mechanics

  • 제28권6호
  • /
  • Pages.677-694
  • /
  • 2008
  • /
  • 1225-4568(pISSN)
  • /
  • 1598-6217(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Design optimization of vibration isolation system through minimization of vibration power flow

  • 투고 : 2007.01.12
  • 심사 : 2008.02.13
  • 발행 : 2008.04.20
⟨ 이전 논문 다음 논문 ⟩

초록

A vibration power minimization model is developed, based on the mobility matrix method, for a vibration isolation system consisting of a vibrating source placed on an elastic support structure through multiple resilient mounts. This model is applied to investigate the design optimization of an X-Y motion stage-based vibration isolation system used in semiconductor wire-bonding equipment. By varying the stiffness coefficients of the resilient mounts while constraining the dynamic displacement amplitudes of the X-Y motion stage, the total power flow from the X-Y motion stage (the vibrating source) to the equipment table (the elastic support structure) is minimized at each frequency interval in the concerned frequency range for different stiffnesses of the equipment table. The results show that when the equipment table is relatively flexible, the optimal design based on the proposed vibration power inimization model gives significantly little power flow than that obtained using a conventional vibration force minimization model at some critical frequencies. When the equipment table is rigid enough, both models provide almost the same predictions on the total power flow.

키워드

참고문헌

  1. Ahn, Y.K., Song, J.D. and Yang, B.S. (2003), "Optimal design of engine mount using an artificial life algorithm", J. Sound Vib., 261, 309-328 https://doi.org/10.1016/S0022-460X(02)00989-6
  2. Alkhatiba, R., Nakhaie, J.G. and Golnaraghi, M.F. (2004), "Optimal design of passive linear suspension using genetic algorithm", J. Sound Vib., 275, 665-691 https://doi.org/10.1016/j.jsv.2003.07.007
  3. Ashrafliuon, H. (1993), "Design optimization of aircraft engine-mount systems", J. Vib. Acoust. Trans., ASME, 115, 463-467 https://doi.org/10.1115/1.2930373
  4. Brake, M.R. and Wickert, J.A. (2005), "Optimizing vibration isolation of flex circuits in hard disk drives", J. Vib. Acoust. Trans., ASME, 127, 165-172 https://doi.org/10.1115/1.1891813
  5. Choy, P.K. and Wong, C.F. (2004), Experimental Characterization for an X-Y Motion Stage Mounting Systems, Technical Report 12156, ASM Assembly Automation Ltd., Hong Kong
  6. Cremer, L., Heckl, M. and Ungar, E.E. (1988), Structure-borne Sound (second edition), Springer-Verlag, Berlin
  7. Fletcher, R. (1987), Practical Methods of Optimization, John Wiley and Sons, New York
  8. Gardonio, P., Elliott, S.J. and Pinnington, R.J. (1997), "Active isolation of structural vibrations on a multipledegree- of-freedom system, Part I: Dynamics of the system", J. Sound Vib., 207, 61-93 https://doi.org/10.1006/jsvi.1997.1152
  9. Goyder, H.G.D. and White, R.G. (1980), "Vibrational power flow from machines into built-up structures: Part I: Introduction and approximate analyses of beam and plate-like foundations", J. Sound Vib., 68, 59-75 https://doi.org/10.1016/0022-460X(80)90452-6
  10. Harris, C.M. (2002), Shock and Vibration Handbook, McGraw-Hill, New York
  11. Koh, Y.K. and White, R.G. (1996), "Analysis and control of vibrational power transmission to machinery supporting structures subjected to a multi-excitation system, Part I: Driving point mobility matrix of beams and rectangular plates", J. Sound Vib., 196, 496-493
  12. Lee, H.J. and Kim, K.J. (2004), "Multi-dimensional vibration power flow analysis of compressor system mounted in outdoor unit of an air conditioner", J. Sound Vib., 272, 607-625 https://doi.org/10.1016/S0022-460X(03)00386-9
  13. Leo, D.J. and Inman, D.J. (1999), "A quadratic programming approach to the design of active-passive vibration isolation systems", J. Sound Vib., 220(5), 807-825 https://doi.org/10.1006/jsvi.1998.1937
  14. Nayfeh, T.A., Emaci, E. and Vakakis, A.F. (1997), "Application of nonlinear localization to the optimization of a vibration isolation system", AIAA J., 35(8), 1378-1386 https://doi.org/10.2514/2.247
  15. Pinnington, R.J. (1987), "Vibrational power transmission to a seating of a vibration isolated motor", J. Sound Vib., 118, 515-530 https://doi.org/10.1016/0022-460X(87)90367-1
  16. Schittkowski, K. (1985), "NLQPL: A FORTRAN-subroutine solving constrained nonlinear programming problems", Ann. Oper. Res., 5, 485-500
  17. Snyman, J.A., Heuns, P.S. and Vermeulen, P.J. (1995), "Vibration isolation of a mounted engine through optimization", Mech. Mach. Theory, 30, 109-118 https://doi.org/10.1016/0094-114X(94)00023-E
  18. Soliman, J.I. and Hallam, M.G. (1968), "Vibration isolation between non-rigid machines and non-rigid foundations", J. Sound Vib., 8, 329-351 https://doi.org/10.1016/0022-460X(68)90236-8
  19. Swanson, D.A., Wu, H.T. and Ashrafiuon, H. (1993), "Optimization of aircraft engine suspension systems", J. Aircraft., 30, 979-984 https://doi.org/10.2514/3.46442
  20. Tao, J.S., Liu, G.R. and Lam, K.Y. (2000), "Design optimization of marine engine-mount system", J. Sound Vib., 235(3), 477-494 https://doi.org/10.1006/jsvi.2000.2945
  21. Yu, Y.H., Peelamedu, S.M., Naganathan, N.G. and Dukkipati, R.V. (2001), "Automotive vehicle engine mounting systems: A survey", J. Dyn. Syst. -T., ASME, 123, 186-194 https://doi.org/10.1115/1.1369361

피인용 문헌

  1. Vibro-acoustic optimization of an immersed cylindrical structure with a floating-raft system inside by using frequency-response-function-based substructuring sensitivity analysis vol.225, pp.2, 2011, https://doi.org/10.1177/1475090211401316
  2. Modeling and optimization of floating raft systems in submarines under different objectives by using hybrid genetic algorithm vol.18, pp.2, 2012, https://doi.org/10.1177/1077546311403184
  3. Application of energy criteria to vibration isolation vol.520, pp.None, 2008, https://doi.org/10.1016/j.jsv.2021.116619