한국유체기계학회 논문집 (The KSFM Journal of Fluid Machinery)

한국유체기계학회 (Korean Society for Fluid machinery)
권호 표지
DOI QR코드

DOI QR Code

분사홀에 설치된 난류촉진제에 따른 충돌/유출면에서의 열/물질전달 특성

Effect of Turbulator on Heat/Mass Transfer for Impingement/Effusion Cooling System

  • 발행 : 2008.12.01
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

In order to enhance the heat/mass transfer, a turbulator has been installed at the exit of injection hole for the impingement/effusion cooling system. The local heat/mass transfer coefficients have been obtained by a naphthalene sublimation method. Experiments have been carried out at the fixed jet Reynolds number of 10,000. Two turbulators with different diameter have been used in the current study. The result presents that the turbulator leads to the increase in flow mixing and jet velocity, consequently enhancing the heat/mass transfer at a stagnation region. Further, the stagnation region is divided into four small areas with peak value. In the existence of initial crossflow, the stagnation regions move downstream and low heat/mass transfer regions are formed regardless of the installation of turbulator. However, the increased jet velocity by turbulator reduces the crossflow effect against the jet, resulting in decrease of low heat/mass transfer regions. Compared to the case without turbulator, the installation of turbulator yields $5{\sim}10%$ augmentation in averaged Sh value.

키워드

참고문헌

  1. Martin, H., 1977, "Heat and mass transfer between impinging gas jets and solid surfaces," Adv. Heat Mass Transfer, Vol. 13, pp. 1-60 https://doi.org/10.1016/S0065-2717(08)70221-1
  2. Viskanta, R., 1993, "Heat transfer to impinging isothermal gas and flame jets," Experimental Thermal and Fluid Science., Vol. 6, pp. 111-134 https://doi.org/10.1016/0894-1777(93)90022-B
  3. Downs, S. J., and James, E. H., 1987, "Jet Impingement Heat Transfer-A Literature Survey," ASME Paper No. 87-HT-35
  4. Wen, M. and Jang, K. 2003, "An impingement cooling on a flat surface by using circular jet with longitudinal swirling strips," International Journal of Heat and Mass Transfer, Vol. 46, pp. 4657-4667 https://doi.org/10.1016/S0017-9310(03)00302-8
  5. Gao, N., Sun, H., and Ewing, D. 2003, "Heat transfer to impinging round jet with triangular tab," International Journal of Heat and Mass Transfer, Vol. 46, pp. 2557-2569 https://doi.org/10.1016/S0017-9310(03)00034-6
  6. Hollwarth, B. R., Lehmann, G. and Rosiczkowski, J., 1983, "Arrays of Impinging Jets with Spent Fluid Removal through Vent Holes on the Target Surface Part 2: Local Heat Transfer," J. of Engineering for Power, Vol. 105, pp. 393-402 https://doi.org/10.1115/1.3227428
  7. Cho, H. H. and Rhee, D. H., 2001, "Local Heat/Mass Transfer Measurement on the Effusion Plate in Impingement/Effusion Cooling System," J. of Turbomachinery, Vol. 123, pp. 601-608 https://doi.org/10.1115/1.1344904
  8. Rhee, D. H., Choi, J. H. and Cho, H. H., 2003, "Flow and Heat (Mass) Transfer Characteristics in an Impingement/Effusion Cooling System with Crossflow," J. of Turbomachinery, Vol. 125, pp. 74-82 https://doi.org/10.1115/1.1519835
  9. 홍성국, 이동호, 조형희, 2005, "가스터빈 연소실 냉각을 위한 충돌제트/유출냉각기법에서 사각핀 설치에 따른 열/물질전달 특성," 유체기계저널, 제8권, 제4호, pp. 39-47 https://doi.org/10.5293/KFMA.2005.8.4.039
  10. Goldstein, R. J. and Cho, H. H., 1995, "A Review of Mass Transfer Measurement Using Naphthalene Sublimation," Experimental Thermal and Fluid Science, Vol. 10, pp. 416-434 https://doi.org/10.1016/0894-1777(94)00071-F
  11. Eckert, E. R. G., 1976, "Analogies to Heat Transfer Processes," in Measurements in Heat Transfer, ed. Eckert, E. R. G. and Goldstein, R. J., pp. 397-423, Hemisphere Pub., New York
  12. Kline, S. J. and McClinetock, F., 1953, "Describing Uncertainty in Single Sample Experiments," Mechanical Engineering, Vol. 75, pp. 3-8

피인용 문헌

  1. A Study on the Model of Thermal Plume Flow in the Forest Fire vol.12, pp.1, 2009, https://doi.org/10.5293/KFMA.2009.12.1.007
  2. vol.12, pp.1, 2009, https://doi.org/10.5293/KFMA.2009.12.1.070